2017 New CGDI Prog BMW

[ASCM]

Same experience for me , i decide to get in garbage , Chinese tool = Chinese shit
never bough this tool !!!!

Maybe Russians are very good for SW crypto and algorithm, why they don't clone correctly explorer

Sent from my 5033F using Tapatalk

[TERMINATOR1000]

Maybe Russians are very good for SW crypto and algorithm, why they don't clone correctly explorer

Sent from my 5033F using Tapatalk

tool is corrupted
never bough this tool !!!!

[hesham10]

hello can it read and write mv1746 isn ? of e90 320

[Crimper999]

This tool is faster on AKL FEM IMO. I’ve got IM608 and the preprocessing steps along with the programming is more time consuming. I have learned a few tricks with this tool. One thing it will do is revive a dead FEM if the FEM is relay is constantly clicking. All you have to do is go into the F/G series programming tab, click on the FEM, then connect the EEPROM adapter for preprocessing to VCI with +12v adapter plugged in. Now connect the EEPROM adapter/clip to the 95128 eeprom. Follow prompts on programming. When the FEM stops clicking, remove EEPROM clip from the FEM and let the tool program the FEM. Now you can go and program the FEM as needed. Hope that helps because I know I had a tough time learning about FEM/BDC programming.

[PixelsFixed]

......I have learned a few tricks with this tool. One thing it will do is revive a dead FEM if the FEM is relay is constantly clicking. All you have to do is go into the F/G series programming tab, click on the FEM, then connect the EEPROM adapter for preprocessing to VCI with +12v adapter plugged in. Now connect the EEPROM adapter/clip to the 95128 eeprom. Follow prompts on programming. When the FEM stops clicking, remove EEPROM clip from the FEM and let the tool program the FEM. Now you can go and program the FEM as needed. Hope that helps because I know I had a tough time learning about FEM/BDC programming.

It doesn't always work, but it can work.

I've had three clicking FEMs. One of them was solved by this process, but the the other two needed new 95128 chips before they'd come back to life.

[ASCM]

It doesn't always work, but it can work.

I've had three clicking FEMs. One of them was solved by this process, but the the other two needed new 95128 chips before they'd come back to life.

Where did you bought new eeproms

Sent from my 5033F using Tapatalk

[PixelsFixed]

Where did you bought new eeproms

Sent from my 5033F using Tapatalk

I bought them on eBay. They arrived in a day or two. Good service.


https://www.ebay.co.uk/itm/192791759254

[hesham10]

Have a look here on new update ... zf6hp isn e series
https://youtu.be/OLWzW1qD6Go

[hesham10]

This one for version not supported .... 8hp f series ... https://youtu.be/4hH2eQHqjto ... if somebody do downgrades please record and upload

[death9891]

CGDI Prog BMW is it possible to run the program without interface? if so, how to cheat it?
mercedes CGMB program, you can

[jurroid]

I bought a BMW CGI Prog for mileage correction, but I could not reset the CAS3+ on the e70 2010.Why if it is stated that there is a mileage reset?Disappointed

[SHD22]

U paid hater )))
How much were u paid ?
http://mhhauto.com/Thread-CGDI-China...ker-BMW?page=2
I know even who paid u ))
CGDI does it work and works great , just believe.
Such person like u administrations of all forums has to give u a bann !!
Ofcourse if this administration is not paid too )))

super good tool, highly recommend.

[teerak2uk]

I bought a BMW CGI Prog for mileage correction, but I could not reset the CAS3+ on the e70 2010.Why if it is stated that there is a mileage reset?Disappointed

Works for me