Register
Results 1 to 10 of 10
  1. #1
    DK Veteran

    Join Date
    Apr 2011
    Location
    Tbilisi
    Posts
    319
    Thanks Thanks Given 
    239
    Thanks Thanks Received 
    56
    Thanked in
    49 Posts

    Default Toyota Highlander 2009 smart key antenna location

    Can anybody please help?
    I can't program the smart key on Toyota Highlander Hybrid 2009. It does not finish the procedure when it says to place the key on the seat and there it can't see the key anymore. I checked under the seat and there's no key, i also checked the middle console but still could not find the antenna. Anybody got a picture where I can see the location of the attached antenna?
    Thanks in advance!

  2. #2
    DK Veteran

    Join Date
    Apr 2011
    Location
    Tbilisi
    Posts
    319
    Thanks Thanks Given 
    239
    Thanks Thanks Received 
    56
    Thanked in
    49 Posts

    Default

    After several ignitions after the smart key reset, the ignition does not turn on. How can i turn it on again with the teachstream or should i do the smart key reset again?

  3. #3
    DK Veteran

    Join Date
    Apr 2011
    Location
    Tbilisi
    Posts
    319
    Thanks Thanks Given 
    239
    Thanks Thanks Received 
    56
    Thanked in
    49 Posts

    Default

    I have 2 error: B2289- Key collation witing time over and b2784- Antenna coil open/short ( I could not find this antenna ). How to turn on the ignition ?

  4. #4
    Member

    Join Date
    Feb 2011
    Location
    USA
    Posts
    78
    Thanks Thanks Given 
    75
    Thanks Thanks Received 
    48
    Thanked in
    21 Posts

    Default

    The Start button or smart ecu is Bad OR Both! i had same thing on 2008 Camry after some one was welding repair the car with 12v battery connected.

  5. The Following User Says Thank You to djeuroalex For This Useful Post:

    Tariel (29th September, 2017)

  6. #5
    V.I.P. Member
    ray-ray's Avatar
    Join Date
    Nov 2009
    Posts
    3,224
    Thanks Thanks Given 
    58
    Thanks Thanks Received 
    2,426
    Thanked in
    1,208 Posts

    Default

    You must of scramble the iD box. Try sync the system ground out 4&13 for 45 min with the button "on".
    also the light trigger on door keep push it to reset. If that does not work then follow these.
    1. Pull out iD box (behind the blower and firewall) reroute it behind the glovebox. Put the dash back together.
    virginize the iD box. Reason for reroute make it easier for you to get to the iD box. You might have to do these a few times. Due to the iD virgin file might be bad. It took me 5 try's before it started.
    2. Do immo. Reset 16min.
    3. Register the iD box to the button
    4. Sync the immo. To the ecu 4/13 for 45 min.
    5. Start car.

  7. The Following 4 Users Say Thank You to ray-ray For This Useful Post:

    alclot (13th December, 2019), djeuroalex (1st October, 2017), McDowell (17th December, 2019), Tariel (29th September, 2017)

  8. #6
    DK Veteran

    Join Date
    Apr 2011
    Location
    Tbilisi
    Posts
    319
    Thanks Thanks Given 
    239
    Thanks Thanks Received 
    56
    Thanked in
    49 Posts

    Default

    Quote Originally Posted by djeuroalex View Post
    The Start button or smart ecu is Bad OR Both! i had same thing on 2008 Camry after some one was welding repair the car with 12v battery connected.
    During the programming (after the reset), when i hold the key at the start button, i can hear the beep (meaning it sees the key). Can it still be damaged in this case?

  9. #7
    DK Veteran

    Join Date
    Apr 2011
    Location
    Tbilisi
    Posts
    319
    Thanks Thanks Given 
    239
    Thanks Thanks Received 
    56
    Thanked in
    49 Posts

    Default

    Thanks ray-ray .

    Is there any other way except removing the ID box? I have never removed an ID box.
    Last edited by Tariel; 29th September, 2017 at 04:37 PM.

  10. #8
    DK Veteran

    Join Date
    Jan 2017
    Location
    USA ����
    Posts
    1,912
    Thanks Thanks Given 
    135
    Thanks Thanks Received 
    676
    Thanked in
    515 Posts

    Default

    if you get the beep that means it sees the key

    so coil is fine in button

  11. #9
    DK Veteran

    Join Date
    Apr 2011
    Location
    Tbilisi
    Posts
    319
    Thanks Thanks Given 
    239
    Thanks Thanks Received 
    56
    Thanked in
    49 Posts

    Default

    Quote Originally Posted by sleepyrz View Post
    if you get the beep that means it sees the key

    so coil is fine in button
    Button is wrong. After replace start button error b2784 is clear. But IGN not run ( B2289- Key collation witing time over ).

  12. #10
    DK Veteran
    alclot's Avatar
    Join Date
    Sep 2009
    Location
    Melee Island
    Posts
    2,629
    Thanks Thanks Given 
    1,936
    Thanks Thanks Received 
    357
    Thanked in
    247 Posts

    Default

    Hi mates,
    I have RAV4 with ecu 89661-42C00 - 175800-7734 and smart key. The dtcs is B2289 and when I push start button dont get on becuase car doesnt recognize the key. Can anyone help me with that?
    Other problem is where is the location of immo box. So hard to take out
    Thanks a lot

  13. The Following User Says Thank You to alclot For This Useful Post:

    McDowell (17th December, 2019)

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.