EDC17CP02, need some help with my mappack

[fzhut]

Hi,

I'm just working on mappack to remap (light stage1 for about 200ps/400nm) my friend's 320dA E91 177hp. Ori file (+mappack) is in attachment, I've read it with kess using boot mode (if anyone needs, I have full recovery). I've created a mappack, whole map list is below. My question is at first - where is single bit of deviation for torque (8 bit to change from 128 to 255). Also if I correctly done all of torque limiters or some need to be added or have bad address (also DW limiters) ? It seems, thet I've lost some SVBL (not sure, in my 318d DDE8 there isn't any) or SVRL. I'm not going to add more than 100 mbar of boost, it also need to have DPF in good condition, so lambda rather wouldn't be lowered more than 3-4%. Any help will be apprechiated with thanks

HW : 08512498
SW : 1037509478

Map addresses :

4060A SVTQL ??
43628 Torque limit 8x12
4A9F2 SVTQL
4AA26 SVTQL
5109C Driver's wish 8x14
511AC Driver's wish 8x14
5821A Torque limit 10x1
5829A Torque limit 8x13
583CE Torque limit 5x16
58634 SVTQL
587B0 Torque limit 21x1
5880E Torque limit 3x21
58938 Torque limit 21x1
58994 Torque%reduction EGT 9x9
58A5E Torque%reduction EGT 9x9
58B42 Torque%reduction oil temp 7x7
58BC4 Torque%reduction oil temp 7x7
5C08A SOI map 16x16
5C2CE SOI map 16x16
5C512 SOI map 16x16
67B8A Duration 40x16 (badly defined in my mappack as 16x40)
69922 N75 16x16
69B66 N75 16x16
69DA2 N75 16x12
69FE6 N75 16x12
6A22C N75 16x13
6A470 N75 16x13
6A6AE N75 14x12
6A842 N75 16x16
6BA16 Boost 16x16
6BC5A Boost 16x16
6BE9A Boost 16x14
6C0E2 Boost 16x16
6C324 Boost 16x15
6C568 Boost 16x15
6C7AE Boost@regeneration 16x16
6C9F2 Boost@regeneration 16x16
6CCB8 Boost limit via Patm 14x16
6E2C0 N75 16x16
724E8 Nm to IQ 16x16
7272C Nm to IQ 16x16
72970 Nm to IQ 16x16
72BB4 Nm to IQ 16x16
72DF8 Nm to IQ 16x16
741A2 Rail limiter 12x8
74B28 Duration 16x16
74E72 Rail limiter 12x8
74F68 Rail map 16x16
75168 Rail map 16x16
75562 Rail map 16x16
7589A Rail map 16x16
76FC8 Torque limiter 8x21
787D2 Torque limiter 10x1
787F8 Torque limiter 1 gear 8x1
7881A Torque limiter 2 gear 8x1
7883C Torque limiter 3 gear 8x1
7885E Torque limiter 4 gear 8x1
78880 Torque limiter 5 gear 8x1
788A2 Torque limiter 6 gear 8x1
788C4 Torque limiter R gear 8x1
7B0C0 Lambda 16x14
7B304 Lambda 16x14
7B548 Lambda 16x14
7B78C Lambda 16x14
7B9D4 Lambda 16x16
7BC18 Lambda@regen 16x16
7BE58 Lambda 16x14
7C09C Lambda 16x14
7C328 Lambda 16x14
7C56C Lambda 16x14
7C7B4 Lambda 16x16
7C9F8 Lambda@regen 16x16

[biela]

Hello

I think it is at 434B3.

74B28 is not Duration.

[fzhut]

Any more advices ? 4 downloads, I belive thet not only for use my mappack, but also for help.

[cunakis]

there is no need for your mappack !
this ecu is simple to tune if you need help to tune it i can do it in realy simple way
post fresh bdm flash read and wait untill i make one simple and strong smokeless