Peugeot EDC16C3 Swap
Register
Results 1 to 7 of 7
  1. #1
    DK Veteran

    Join Date
    Jan 2010
    Location
    Northern europe
    Posts
    395
    Thanks Thanks Given 
    111
    Thanks Thanks Received 
    71
    Thanked in
    39 Posts

    Default Peugeot EDC16C3 Swap

    Hey guys.

    I have a Peugeot 206 with EDC16C3 where I think ECU has some problems when hot and want to make a swap with another EDC16C3 to test.

    I have full BDM read of the old ecu and will do the same on "new" ecu.
    Do I need to copy EEPROM + Flash + MPS or only Eeprom+Flash ?

    Thanks in advance.

  2. #2
    DK Veteran
    dominik.m's Avatar
    Join Date
    Jun 2009
    Location
    POLAND
    Posts
    3,427
    Thanks Thanks Given 
    409
    Thanks Thanks Received 
    2,636
    Thanked in
    1,461 Posts

    Default

    If HW and SW are the same, this will suffice flash + eeprom.
    Treat the best to copy the whole.

  3. The Following User Says Thank You to dominik.m For This Useful Post:

    jaxone (14th August, 2018)

  4. #3
    DK Veteran

    Join Date
    Jan 2010
    Location
    Northern europe
    Posts
    395
    Thanks Thanks Given 
    111
    Thanks Thanks Received 
    71
    Thanked in
    39 Posts

    Default

    Bosch numbers are not the same , but both ecu's are EDC16C3.
    Will check the "new" one when it comes, to be sure same MPC.

    I was thinking more at the CS between flash / MPC / eeprom.
    Working with Ktag original.

  5. #4
    DK Veteran

    Join Date
    Sep 2016
    Location
    Poland
    Posts
    2,226
    Thanks Thanks Given 
    81
    Thanks Thanks Received 
    1,076
    Thanked in
    748 Posts

    Default

    upload bosch number orginal ecu
    FILE SERVICE

  6. The Following User Says Thank You to voltechcar For This Useful Post:

    jaxone (14th August, 2018)

  7. #5
    DK Veteran

    Join Date
    Jan 2010
    Location
    Northern europe
    Posts
    395
    Thanks Thanks Given 
    111
    Thanks Thanks Received 
    71
    Thanked in
    39 Posts

    Default

    Tested only with Eeprom and Flash , no go.
    So I had to make full restore to new ECU. Car starts and drives so ECU is ok.
    Still cutting power while driving , so next step is BSI.

    Thanks everyone for input.

  8. #6
    DK Veteran

    Join Date
    Sep 2016
    Location
    Poland
    Posts
    2,226
    Thanks Thanks Given 
    81
    Thanks Thanks Received 
    1,076
    Thanked in
    748 Posts

    Default

    upload flash maybe whos cut dtc......
    FILE SERVICE

  9. #7
    DK Veteran

    Join Date
    Jan 2010
    Location
    Northern europe
    Posts
    395
    Thanks Thanks Given 
    111
    Thanks Thanks Received 
    71
    Thanked in
    39 Posts

    Default

    Here is the Flash.

    It feels like 12v is cut off from ecu after car gets warm... so I don't think flash is the problem.
    P0183 - Fuel Temperature Sensor A Circuit High Input
    P0382 - Glow Plug/Heater Circuit B Malfunction
    P1666 - Unknown fault code
    P0343 - Camshaft Position Sensor Circuit High Input
    P0337 - Crankshaft Position Sensor A Circuit Low Input
    Attached Files Attached Files

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.