Opel CD30 unregister it

**kwansterp** · 26th September, 2018, 03:12 PM

Hi
I need unregister for this Radio
OPEL CD30 by BLAUPUNKT
13190856
inside 95640

Thank you in advance

**bank** · 26th September, 2018, 03:13 PM

Unregistered

**kwansterp** · 26th September, 2018, 03:19 PM

This is a completely different file, from another radio.

**criollo** · 26th September, 2018, 03:46 PM

7664 ------------

**shooting** · 26th September, 2018, 04:05 PM

Originally Posted by kwansterp

This is a completely different file, from another radio.

Here you go

wbr

**bank** · 26th September, 2018, 04:12 PM

Originally Posted by kwansterp

This is a completely different file, from another radio.

Yes, exactly. It's a virgin dump for cd30 Blaupunkt YY

**kwansterp** · 26th September, 2018, 04:38 PM

The pin 7664 is good but I can not deactivate my Op-com. Still display safe. FVDI has a message about unsuccessful deactivation.
I am probably trying to make a ready file from shooting.

**bank** · 26th September, 2018, 05:01 PM

Originally Posted by kwansterp

The pin 7664 is good but I can not deactivate my Op-com.

Use one of received virgin dumps, set correct config in mid speed can bus and pair using code from display

**shooting** · 26th September, 2018, 05:52 PM

Originally Posted by kwansterp

The pin 7664 is good but I can not deactivate my Op-com. Still display safe. FVDI has a message about unsuccessful deactivation.
I am probably trying to make a ready file from shooting.

Just use my dump and enjoy

wbr

**kwansterp** · 26th September, 2018, 06:57 PM

The shooting files and the bank are good. Every few seconds beep ... beep. I can not marry them with the display. My two Op-com can not make it. But I heard that it happens. I need to ask to pair files from the radio and display.
I'm sending a file from the display.

Borg 13208089 AT
93c56 x8bit

Thanks in advance

**bogege** · 26th September, 2018, 07:38 PM

The password of the car should be:3507 Use it for marriage!

**kwansterp** · 27th September, 2018, 10:18 AM

The pin is known to me, correct, but I have nothing to pair the radio and display with.
Can I ask for paired files for radio and display.

**shooting** · 27th September, 2018, 10:20 AM

Originally Posted by kwansterp

The pin is known to me, correct, but I have nothing to pair the radio and display with.
Can I ask for paired files for radio and display.

Just use OPCOM... 2 minute job

wbr

**kwansterp** · 27th September, 2018, 10:46 AM

My op-com 1.39 and 1.59 can not do it. I do not know why myself. Unless I'm doing something wrong.
EHU -> Prog .. -> activate protect -> PIN -> Successfully completed. I turn the radio off for about 1 minute and it still does not work.

**shooting** · 27th September, 2018, 11:34 AM

Originally Posted by kwansterp

My op-com 1.39 and 1.59 can not do it. I do not know why myself. Unless I'm doing something wrong.
EHU -> Prog .. -> activate protect -> PIN -> Successfully completed. I turn the radio off for about 1 minute and it still does not work.

What's on the display?

wbr

SEE BELOW:

CD30 Error Messages
===================

If you see "DISPLAY SAFE" permanently shown after 10 seconds,
this means that the Display has not been correctly programmed to the vehicle.

If you see "DISPLAY SAFE" flashing every 10 seconds, this means that the Display
is currently in Delivery Mode, and is now ready to be programmed to the vehicle
with a OBDII programmer.

If you see "RADIO SAFE" permanently shown after 10 seconds,
this means that the Radio has not been correctly programmed to the vehicle.

If you see "RADIO SAFE" and a beep every 10 seconds, this means that the Radio
is currently in Delivery Mode, and is now ready to be programmed to the vehicle
with a OBDII programmer.