Peugeot Boxer EDC15C7 IMMO OFF needed
Register
Results 1 to 8 of 8
  1. #1
    DK Veteran
    Join Date
    Dec 2016
    Location
    Poland
    Posts
    312
    Thanks
    189
    Thanked 28 Times in 23 Posts
    Downloads
    6
    Uploads
    0

    Default Peugeot Boxer EDC15C7 IMMO OFF needed

    HI!

    I need immo off for EDC15C7 in Peugeot Boxer from 2001 year 2.8HDI

    HW: 0281010486
    SW: 1037360012


    I post ori FLASH and EEPROM.

    Please someone make IMMO OFF or give instruction how to change dump.

    Will Rep and THX

    Thanks
    Kuba
    Attached Files Attached Files
    >>Genuine Winols, Swiftec, Ktag, Flex, x17<<
    >Diagnostic, Chiptuning, Dashbord<

  2. #2
    DK Veteran

    Join Date
    Feb 2017
    Location
    Eu
    Posts
    369
    Thanks
    143
    Thanked 233 Times in 180 Posts
    Downloads
    4
    Uploads
    0

    Default

    @kubuswujo
    Correct cksm in writing...
    edc15c7 PSA (2-plug)
    Attached Files Attached Files
    Last edited by fabrag; 4th January, 2019 at 09:58 AM.

  3. The Following User Says Thank You to fabrag For This Useful Post:

    kubuswujo (4th January, 2019)

  4. #3
    DK Veteran
    Join Date
    Dec 2016
    Location
    Poland
    Posts
    312
    Thanks
    189
    Thanked 28 Times in 23 Posts
    Downloads
    6
    Uploads
    0

    Default

    @Fabrag i made checksum with mpps and your file not working...
    Car does not start.

    And to read this ecu on bench i had to unsolder immo eeprom. From information in forum i have read that to read EDC15C7 on bench via pinout i need to:
    unsolder eeprom
    or make immo off in flash.

    But when i have written your immo off solution, the car does not start.
    And after soldering eeprom i still cannot read/write it using kess or mpps. When i usnolder eeprom then i can read write ecu via pinout.

    so can someone send working solution?
    >>Genuine Winols, Swiftec, Ktag, Flex, x17<<
    >Diagnostic, Chiptuning, Dashbord<

  5. #4
    DK Veteran

    Join Date
    Feb 2017
    Location
    Eu
    Posts
    369
    Thanks
    143
    Thanked 233 Times in 180 Posts
    Downloads
    4
    Uploads
    0

    Default

    Hi Kubuswujo,
    Sorry to hear that...
    The immo is in the flash (29F400) and nowhere else...
    Are u sure cksm is ok?

    You can try this file if you want (cksm ok)
    Last edited by fabrag; 4th January, 2019 at 04:39 PM.

  6. The Following User Says Thank You to fabrag For This Useful Post:

    kubuswujo (4th January, 2019)

  7. #5
    Member

    Join Date
    Nov 2009
    Posts
    78
    Thanks
    15
    Thanked 55 Times in 45 Posts
    Downloads
    14
    Uploads
    0

    Default

    HI YOUR OFF
    TRY AND POST RESULT
    Attached Files Attached Files

  8. The Following 3 Users Say Thank You to kino123 For This Useful Post:

    kubuswujo (4th January, 2019),mikroel (28th March, 2019),petrevichmail (11th April, 2019)

  9. #6
    DK Veteran
    Join Date
    Dec 2016
    Location
    Poland
    Posts
    312
    Thanks
    189
    Thanked 28 Times in 23 Posts
    Downloads
    6
    Uploads
    0

    Default

    Thanks a lot.
    I will try tommotow both solutions i think that checksum were ok but i post file from mpps.
    Will report if it work.
    As i understand on good working immo of
    i should be able to read this ecu with eeprom soldered so it is easy to find out if immo off is working or not.
    Attached Files Attached Files
    >>Genuine Winols, Swiftec, Ktag, Flex, x17<<
    >Diagnostic, Chiptuning, Dashbord<

  10. The Following 2 Users Say Thank You to kubuswujo For This Useful Post:

    fabrag (4th January, 2019),petrevichmail (11th April, 2019)

  11. #7
    DK Veteran peko's Avatar
    Join Date
    Jan 2010
    Posts
    1,208
    Thanks
    65
    Thanked 47 Times in 41 Posts
    Downloads
    9
    Uploads
    0

    Default

    hi friends

    which file working fine ?

    thanks

  12. #8
    DK Veteran
    Join Date
    Dec 2016
    Location
    Poland
    Posts
    312
    Thanks
    189
    Thanked 28 Times in 23 Posts
    Downloads
    6
    Uploads
    0

    Default

    kino 123 works!
    >>Genuine Winols, Swiftec, Ktag, Flex, x17<<
    >Diagnostic, Chiptuning, Dashbord<

 

 

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •