MPPS CAN I USE IT TO READ AND WRITE COMFORT CONTROL MODUEL
Register
Results 1 to 6 of 6
  1. #1
    DK Veteran WOODWARD395's Avatar
    Join Date
    Apr 2010
    Location
    Manchester UK
    Posts
    602
    Thanks
    425
    Thanked 107 Times in 84 Posts
    Downloads
    52
    Uploads
    0

    Question MPPS CAN I USE IT TO READ AND WRITE COMFORT CONTROL MODUEL

    Hi I have a problem with my VW Touran 2007 se 1.9tdi the passenger side windows and central locking will not work and I cannot open the doors from inside or out I suspect the comfort control module and was wondering the best way to copy the code from my old one to replace with same part number 1k0959433BT and copy data to it as VW want 200+ to do the task.
    Any advice welcome thanks.
    Education is not the learning of facts, But the training of the mind to think


    So hit the thanks button if I have enlightened you.

  2. #2
    DK Veteran

    Join Date
    Jan 2010
    Location
    Germany
    Posts
    433
    Thanks
    182
    Thanked 118 Times in 77 Posts
    Downloads
    13
    Uploads
    0

    Default

    Mpps no way. Try to open door somehow and check wiring between door and car.
    What fault codes do you have on comfort module?


    Sent from my iPhone using Tapatalk Pro

  3. The Following User Says Thank You to ollync For This Useful Post:

    WOODWARD395 (15th January, 2019)

  4. #3
    Member
    Join Date
    Jan 2019
    Location
    Switzerland
    Posts
    54
    Thanks
    24
    Thanked 22 Times in 13 Posts
    Downloads
    0
    Uploads
    0

    Default

    I think you have to buy a new one or look after a used one an remove the component protection. But i normaly you have to learn the new one to the car.

  5. The Following User Says Thank You to Cyrez For This Useful Post:

    WOODWARD395 (15th January, 2019)

  6. #4
    DK Veteran WOODWARD395's Avatar
    Join Date
    Apr 2010
    Location
    Manchester UK
    Posts
    602
    Thanks
    425
    Thanked 107 Times in 84 Posts
    Downloads
    52
    Uploads
    0

    Default

    I am using a VAG K+CAN V3.6 to get these codes I am almost certain one of the electrical units or relays is causing my problems through ingress of water, here's what what I am getting.

    symptoms doors will not open on passenger side rear as well now checked harnesses and fuses when doors would open already all seem ok.
    engine has lack of power as if in limp mode but did recover for 15mins then no power again dash says doors are open permanently engine light comes on intermittently but mainly off.
    vag 2k2955119
    1/4 324B
    sporadic error
    lower limit exceeded
    2/4 3935
    sporadic error
    missing data or wrong setting adaption
    3/4 3131
    sporadic error
    cut in short to ground
    4/4 4320
    sporadic error
    lower limit exceeded


    1k0947291f
    1/3 0142
    permanent error
    unplausable signal

    2/3 0534
    permanent error
    missing signal/communication
    3/3 0535
    permanent error
    missing signal/ communication

    1T0959701D
    1/1 03AO
    sporadic error
    unplausable signal

    1K0959704AK
    1/1 0533
    sporadic error
    missing signal/communication


    1K0953549BC
    1/1 0373
    sporadic error
    electrical error in power cycle

    1K0815071R
    1/2 0298
    permanent error
    lower limit exceeded

    2/2 08CB
    permanent error

    1k097530k
    1/4 0533
    missing signal/communication
    2/4 0534
    permanent error
    missing signal/communication
    3/4 0535
    permanent error
    missing signal/communication
    4/4 0536
    sporadic error
    missing signal/communication
    Last edited by WOODWARD395; 15th January, 2019 at 08:57 AM.
    Education is not the learning of facts, But the training of the mind to think


    So hit the thanks button if I have enlightened you.

  7. #5
    DK Veteran

    Join Date
    Jan 2010
    Location
    Germany
    Posts
    433
    Thanks
    182
    Thanked 118 Times in 77 Posts
    Downloads
    13
    Uploads
    0

    Default

    Do you have another tool to scan the error codes? VCDS would be recommended.
    To change the CCM in this car you don't need dealer (module has no component protection as i can remember , somebody correct me if i am wrong),
    just get coding with VCDS from old module, write coding to your replacement module and adapt remotes and it must work.
    All you need you can find here http://wiki.ross-tech.com/wiki/index...Comfort_System.
    But i think you have more problems than the CCM module.
    A complete scan with a right tool will give us more information about your problems.

  8. The Following User Says Thank You to ollync For This Useful Post:

    WOODWARD395 (15th January, 2019)

  9. #6
    DK Veteran WOODWARD395's Avatar
    Join Date
    Apr 2010
    Location
    Manchester UK
    Posts
    602
    Thanks
    425
    Thanked 107 Times in 84 Posts
    Downloads
    52
    Uploads
    0

    Default

    Have been looking at ross-tech for VCD'S but above my budget at present have been offered ross-tech cable HEX V2 and software18.9 Chinese hack for just over 50 but cannot update software but never trusted Chinese software is it worth the risk.
    The car seems to be having a lot of electrical problems at present so definitely need a better tool as just working in the dark as don't have a full read.
    Education is not the learning of facts, But the training of the mind to think


    So hit the thanks button if I have enlightened you.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •