xprog 5.5.5 problem

**sergei5005** · 22nd March, 2019, 12:16 PM

My Xprog have 93LC46B. This is 16 bit mode. See this dump sector 20190322_080613.jpg. Digital signature of the manufacturer.You read in 8 bit mode,you not see this. The problem with "certificate error" veryfi you hour and day configuration in your operative system.

**PaoloDigital** · 22nd March, 2019, 08:44 PM

Thanks for your disponibilty

**sergei5005** · 22nd March, 2019, 09:01 PM

Only verify correct year, day and hour actual in your windows O.S. Im have back time "certificate error" because bad calendar in my windows O.S

**PaoloDigital** · 22nd March, 2019, 10:27 PM

Thanks, but error i

**sergei5005** · 22nd March, 2019, 11:49 PM

Yes. im changed other firmware 5.5.5 and not found. The firmaware upload for my found OK in my Xprog box. You need search other file dump for you Xprog. In Download area in this forum have other firmware . You can download .

**PaoloDigital** · 22nd March, 2019, 11:52 PM

Thanks not and

**sergei5005** · 22nd March, 2019, 11:53 PM

See this https://www.digital-kaos.co.uk/forum...&id=34&page=14 and compare its same a back file.

**MOTO MAN** · 23rd March, 2019, 07:37 AM

It's very simple and it doesn't have to be that complicated. Refresh a 5.5.5 firmware directly. Of course, you have to match the software.

**sergei5005** · 23rd March, 2019, 11:15 AM

Im download my software here : https://www.digital-kaos.co.uk/forum...&id=34&page=20 Because original CD is broken in shipping. With firmware upload for my works OK. ( in my Xprog box of course). Sorry friends. More help im not have.

**PaoloDigital** · 23rd March, 2019, 11:37 AM

Thanks for All fake

**sergei5005** · 23rd March, 2019, 11:53 AM

Try you download software from here site ??? For reprogrammieng ATMEGA64 first is need erase all microcontroller and next reprogramming with UPA. Im sugered reprogrammig firmware,read andveryfy after programmin the correct data e install this software from here before Buy other microcontroller. Do not give up. it Is difficult but is possible. Im make is only a few days back.

**sergei5005** · 23rd March, 2019, 12:08 PM

Hi friend. Try all other time. Donload you software from here : https://www.digital-kaos.co.uk/forum...&id=34&page=20

Erase all microcontroller and change this firmware :
After programming verify correct data , fuses and lock bit configuration in you ATMEGA 64.
ANd verifi in you windows O.S /contol panel/dvices the correct instalation of your hardware. See USB devices and LPT ports sctor (is USB you device,off course). You need instaler Xprog in this 2 sectors.Will found OK.

**xoom** · 23rd March, 2019, 12:14 PM

Lock Bits are important for xprog

**besriworld** · 4th December, 2022, 09:05 PM

Hello ,
I have a problem reading this processor Micronas CDC3217G. The dashboard is: 8P0920982H
I bought Xprog V5.5.5 . Successfully read the old dashboard witch number : 8P0 920 900 S
But the new board always reads it wrongly and gives an error verify error The connections are the same.
Can you help me ? I bought a second xprog and it works the same way.

**besriworld** · 9th December, 2022, 08:08 PM

I found the problem. The problem is that the board is new and the program does not support it. It just can't pass security.
I deleted the flash and saved the flash from the old dashboard. Now the verification passes successfully every time.

Now I need help. Can you transfer the data from the old dashboard or give me a dump of this 8P0920982H dashboard. Thanks!