UPA USB user manual help

[adam28]

Hello people,

My UPA USB programmer arrived today.
There was no user manual or anything. Does anyone have one?

Much appreciated


Regards

Adam

[elektro128]

Hello people,

My UPA USB programmer arrived today.
There was no user manual or anything. Does anyone have one?

Much appreciated


Regards

Adam

hi

for You

regards

[gezame]

Hi,
The manual, you can open it within the software, install soft, run, help-contents
Regards.

[adam28]

How do i get the full software? this did not come with it.
I did buy from elrasoft.

Cheers

[z786]

they should email you a link with password, u shud find wat u need there

[adam28]

Ive sent them a email so hopefully all will be sorted soon.

I thought it would have come with a ribbon to connect to the programmer and the other end to solder to the components.

[grezacediagnostics]

Hello people,

My UPA USB programmer arrived today.
There was no user manual or anything. Does anyone have one?

Much appreciated


Regards

Adam

Whats one of these could you put a link so can see what you bought pal

[z786]

Whats one of these could you put a link so can see what you bought pal

here u go mate

ELRASOFT Products

[PremierD]

Ive sent them a email so hopefully all will be sorted soon.

I thought it would have come with a ribbon to connect to the programmer and the other end to solder to the components.

Its just a stanard 9 pin D sub connector mate...Easy to make up .. I use a multi colourd ribbon .. makes it easier to remember Pins 1>9...Select New programmer.. right hand side ,select what you want to read.. press help >contents.. then your chosen MCU... if you look at the bottom of the right column .. you see two tabs .. Programmer/ Connections .. once connected up click the connectios tab.. this will tell you if all your connectios are correct.....SIMPLES....

[adam28]

cheers guys, everything is up and running now. Its alot better than the Xprog-t that i was using. Just a shame that they dont sell any adapters for onboard programming. Only the tms adapter which i didnt buy yet. I did buy the 78K0/HC912 Adapter though.

[PremierD]

cheers guys, everything is up and running now. Its alot better than the Xprog-t that i was using. Just a shame that they dont sell any adapters for onboard programming. Only the tms adapter which i didnt buy yet. I did buy the 78K0/HC912 Adapter though.

Great little programmer mate...I have always foud Penko to be very helpfull .. He has in the past sent Diagrams to make up your own adaptors ...E-mail him if you have a problem...

[adam28]

Its just a stanard 9 pin D sub connector mate...Easy to make up .. I use a multi colourd ribbon .. makes it easier to remember Pins 1>9...Select New programmer.. right hand side ,select what you want to read.. press help >contents.. then your chosen MCU... if you look at the bottom of the right column .. you see two tabs .. Programmer/ Connections .. once connected up click the connectios tab.. this will tell you if all your connectios are correct.....SIMPLES....

Where did you get your coloured ribbon from? Thanks for the heads up on Penko Cheers

[PremierD]

RS components... mate ...

[^^TommyTee]

Hello people,

My UPA USB programmer arrived today.
There was no user manual or anything. Does anyone have one?

Much appreciated


Regards

Adam

hello adam

how much was you upa programmer m8 ?

and does it support ATtiny45 EEPROM ?

I looking too buy a willem programmer or one that supports a wide range of EEPROMS

[adam28]

hello adam

how much was you upa programmer m8 ?

and does it support ATtiny45 EEPROM ?

I looking too buy a willem programmer or one that supports a wide range of EEPROMS

I think i payed about 150 pound for it mate. I also ordered this which may be good for you.MCUmall Electronics Inc. A low cost EPROM EEPROM Atmel PIC I2C SPI programmer online store.
Depends how much you got to spend. Also take alook at some other programmers from the link you may find something cheaper that suits you better.

Will have to check if it does ATtiny45 EEPROM have not need to use for this yet. But dont think so. ELRASOFT Products

Cheers mate

Adam