No just reed pin an do it with blanc transponer
Wysłane z iPhone za pomocą Tapatalk
I had a spare key job today, 2006 polo 9N3 model.
I tried with FVDI, Wizard - It autodetected CS & PIN, precoded a dealer key, but when it went to key learn, it would only learn the customers original key. So immo light kept flashing.
When i went through again, and put 1 key required, it learnt his key and immo light went out.
I tried it a couple of times, so locked a couple of ID48's. Im sure i also tried a blank unlocked ID48, not precoded.
So just wondering, does it need CS prepared key on these 9n3 polo's or not? , I finished job by cloning in the end but would like to know for future.
I also have VVDI2 but i wasnt sure if this would work on old system like this polo has?
Tools owned -
AD100 PRO, Lonsdor, FVDI 18, FVDI 20, VVDI PROG, VVDI2, VVDI MB
CGDI BMW, SuperVag, Renault ECU tool, OBDstar X300 DP Plus, AUTEL im508
VVDI Mini Keytool, KeyDIY KDX2, SBB, ACDP CAS/KVM
Opcom, VCDS pro, Diagbox, Multiecuscan, Forscan, JLR SDD
No just reed pin an do it with blanc transponer
Wysłane z iPhone za pomocą Tapatalk
Had this same issue with Polo , tried several chips, blank 48, can version, EM4701, etc. and all in a sudden got a chip that did the job. No idea what the difference was , but the 1-2 issue on the instrument screen and the SAFE are gone and have 2 good keys now. Would love to know what was the trick since I had a caddy 2009 a while ago with same issue and that one has not been done (could not clone at the time, should be better covered now).
Caddy need precoding. Different than Polo 9N
Very strange, im sure i tried KEY LEARN and just tried an unlocked blank 48 chip and still no luck. I guess ill try to clone these generation polo in future unless its all keys lost and im forced to try and add a TP
Tools owned -
AD100 PRO, Lonsdor, FVDI 18, FVDI 20, VVDI PROG, VVDI2, VVDI MB
CGDI BMW, SuperVag, Renault ECU tool, OBDstar X300 DP Plus, AUTEL im508
VVDI Mini Keytool, KeyDIY KDX2, SBB, ACDP CAS/KVM
Opcom, VCDS pro, Diagbox, Multiecuscan, Forscan, JLR SDD
I use SBB for programming Polo 9N and never had problems
From my experience it is worse to have it with correct CS data precoded. Take into consideration that there is no TP2x transponder. When you have car still with you send me e2 and i make trick that will accept any id48.
Why go through all that hassal when you could have clone the ID48 chip and away you go....
Tools owned: Hammer, Chisel, Crowbar, Punch, Chainsaw, Cutter and Brain!!!
Did you know People will question all the good things they hear about you but believe all the bad without a second thought.
Note:All information given is to be used for educational purposes only and should not be taken seriously.
godfathertre (14th June, 2019)
I had an Audi A4 earlier that day, which i do clone because i know they can be a nightmare programming wise,
And i had left no points on my Keytool, so i wanted to learn it
Tools owned -
AD100 PRO, Lonsdor, FVDI 18, FVDI 20, VVDI PROG, VVDI2, VVDI MB
CGDI BMW, SuperVag, Renault ECU tool, OBDstar X300 DP Plus, AUTEL im508
VVDI Mini Keytool, KeyDIY KDX2, SBB, ACDP CAS/KVM
Opcom, VCDS pro, Diagbox, Multiecuscan, Forscan, JLR SDD
why waste time for later vag cloning safer faster and away to next job it amazes me wasting hours pulling pin codes when cloning 5 minutes top .
I had a sister of Polo, Ibiza 2003 1,4 diesel.
Same issue. 2 transponders one by one works great, both programmed didn t.
2006 on polo is a cross over year could be T6 id48 or it may have needed TP23 id48 canbus , so if left flashing it may be because you needed a canbus chip
also depends on whether your using original chips or aftermarket , alot of the aftermarket chips get rejected by the system , yet will work on another one .
sometimes with polo you have to wait for 30 mins with ignition on after pulling pin to code key in.
abrites has always had issues leaving immo light flashing on alot of vag , so i assume the snide fvdi has same issue as a poor copy of it , other kit saves the day when you have the pin code . the more options you have to use the better as one succeeds where others fail and vice versa .
klauss78 (14th June, 2019)
klauss78 (26th June, 2019)
If i may add,my personal experience with 3 x 9N 2006 polo's , always have been the same, some T6 chip, which failed with avdi and ad100, worked with vcds with ignition on for 15 minutes @ first.
Last edited by nazz2; 14th June, 2019 at 09:56 PM.
Bookmarks