Nissan Hardbody

[BraLaas]

Good day

Could someons please assist me with pinout for Speed input
I have to repair cluster

Any help will be much appreciated
Thank you

Sent from my MAR-LX1M using Tapatalk

[jomberykaso]

Good Luck!

IMG_20181008_151650.jpg

terr.jpg

Credits to @letalcrudo for his pictures.

[Killer76]

What year is the cluster ?

[jomberykaso]

What year is the cluster ?

2011 - 2014

[sagie1zn]

what is best procedure to remove and replace needles on these type of nissan clusters that have a pin to stop needle from going below zero. Basically how to re-calibrate

[jomberykaso]

Remove and replace needles is easy, to re calibrate them you can plug dash to the vehicle and turn the ignition on then put needles. However ever I use other technique but it's difficult to me to explain you in english language.

[Meat-Head]

On topic:-

wont argue but the board is marked near connector, power and ground

speed pulse, sorry can’t tell you pins, is 9vac. 2 wires to sender

get costumer to photo plug in dash and at sensor end

aleo common for loom Snapoibg as it goes to gearbox

[BraLaas]

On topic:-

wont argue but the board is marked near connector, power and ground

speed pulse, sorry can’t tell you pins, is 9vac. 2 wires to sender

get costumer to photo plug in dash and at sensor end

aleo common for loom Snapoibg as it goes to gearbox

My problem is that the speed meter is only working at high speeds
I have put an wire to cancel wiring but still the same problem

Sent from my MAR-LX1M using Tapatalk

[jomberykaso]

I think speed needle is bad recalibrate only

[Meat-Head]

Good day

Could someons please assist me with pinout for Speed input
I have to repair cluster

Any help will be much appreciated
Thank you

Sent from my MAR-LX1M using Tapatalk

Good Luck!

IMG_20181008_151650.jpg

terr.jpg

Credits to @letalcrudo for his pictures.

What year is the cluster ?

2011 - 2014

what is best procedure to remove and replace needles on these type of nissan clusters that have a pin to stop needle from going below zero. Basically how to re-calibrate

Remove and replace needles is easy, to re calibrate them you can plug dash to the vehicle and turn the ignition on then put needles. However ever I use other technique but it's difficult to me to explain you in english language.

On topic:-

wont argue but the board is marked near connector, power and ground

speed pulse, sorry can’t tell you pins, is 9vac. 2 wires to sender

get costumer to photo plug in dash and at sensor end

aleo common for loom Snapoibg as it goes to gearbox

My problem is that the speed meter is only working at high speeds
I have put an wire to cancel wiring but still the same problem

Sent from my MAR-LX1M using Tapatalk

I think speed needle is bad recalibrate only

why do people fully quote other members posts, clogs forum up

ADVERTISEMENT:-

try looking at this

http://www.codecard.eu/electronics/s...prod_2340.html

[SEAT.]

Easy to calibrate these needles use common sense is the answer

[BraLaas]

Easy to calibrate these needles use common sense is the answer

Please read post again, and then use some common sense
Post is not about needle calibration


Sent from my MAR-LX1M using Tapatalk

[BraLaas]

why do people fully quote other members posts, clogs forum up

ADVERTISEMENT:-

try looking at this

http://www.codecard.eu/electronics/s...prod_2340.html

Thank you but have problem sorted burned track

Sent from my MAR-LX1M using Tapatalk

[SEAT.]

Wasn't referring to ur post boet