Dacia Sandero II 2013 - ECU: Valeo V42 not starting after dead battery

[rafal]

my renolinc is 1.52 were i can downoad this version and will need to be update firmware

http://immoff17advancedautomotiveimm...al-latest.html

[tugishrugish]

Hi all i tried with 1.87 but not sucsses vin cannot write then uploud virgin file on ecu and now vin is correct but not start and cannot learn ecu ...
I will try with another files files for ucc and ecu and will learn new key but I do not find for now

[speedy100]

Hi all i tried with 1.87 but not sucsses vin cannot write then uploud virgin file on ecu and now vin is correct but not start and cannot learn ecu ...
I will try with another files files for ucc and ecu and will learn new key but I do not find for now

Hi,
Did You buy a new red cable or ver. 1.87 runs with old blue cable?

Best Regards

[rafal]

Hi,
Did You buy a new red cable or ver. 1.87 runs with old blue cable?

Best Regards

working only with red..............

[tugishrugish]

Hi
yes i buy a new red cable with registered versinon 1.87

[speedy100]

Hi
yes i buy a new red cable with registered versinon 1.87

Total cost please?

[tugishrugish]

85€ Total

[Patrick190e]

im in the same boat, no vin no start... any suggestion??

[rafal]

im in the same boat, no vin no start... any suggestion??

read again everything in this thread

[Patrick190e]

i read the entire thread, i have the red 1.87 renolink. i use this method:

"open renolink go to extra and go to keys and choose UCH T4 LEARNING ECM don't turn the ignition onclic on read pin
after 30 or 40 seconds renolink give pin code and ISK code
turn the ignition on clic connect and wait renolink to connected
Finally clic to start lerning
turn the ignition off
and start the car
this solition of renolink V182 184

now i have fuel pump but car no start, have 2 codes p1351 p1352 (bad coil 1/4,2/3)... no spark at all, try change the coil pack and no succes... something weird is when renolink read the key code a red message appears "pin not recognised make sure ignition is on" is that normal?

[Meat-Head]

Start with checking fuses as first step, goes for anymember with red rep points

[Patrick190e]

Start with checking fuses as first step, goes for anymember with red rep points

all fuses are ok... actually the coil receive 12v temporary with the fuel pump...

what do you mean with "red rep points"???

[JETRONIC1]

hello,the learning was done right? I can help with the learning and the codes.. .do you have can clip?

[Patrick190e]

hello,the learning was done right? I can help with the learning and the codes.. .do you have can clip?

hi, i have renolink 1.87 red cable, the car was battery flat problem... so i bought renolink... i follow the instructions down below

"open renolink go to extra and go to keys and choose UCH T4 LEARNING ECM don't turn the ignition onclic on read pin
after 30 or 40 seconds renolink give pin code and ISK code
turn the ignition on clic connect and wait renolink to connected
Finally clic to start lerning
turn the ignition off
and start the car"

car wont start, the software says "pin not recognized, make sure the ignition is off" and the key transponder shows 0000000... after that procedure fuel pump comes on but i have no spark, install a new coil pack and nothing.

my pin is 4B44D34D8B56A9F85E08A4828E4DD595 but software says is invalid. i try with clear UCH with no succes... now key transponder (in learning procedure) doe't show any key transponder, fuel pump wont come on, now im really lost with that.

PLEASE HEEEEEEEEEEELP ME!!!!

[Patrick190e]

after few tryes, i finally program the ecm, but now i have a weird code : 9560 description ##38240# status dtc 169... i dont have any idea what thats code means... any help??