sdnatlst (25th January, 2020)
sdnatlst (25th January, 2020)
Thanks rapid, strange without tension i had a good strong bounce on wafer 8,, but your right it was a 1 cut on the last cut from customers key!
Tools owned -
AD100 PRO, Lonsdor, FVDI 18, FVDI 20, VVDI PROG, VVDI2, VVDI MB
CGDI BMW, SuperVag, Renault ECU tool, OBDstar X300 DP Plus, AUTEL im508
VVDI Mini Keytool, KeyDIY KDX2, SBB, ACDP CAS/KVM
Opcom, VCDS pro, Diagbox, Multiecuscan, Forscan, JLR SDD
i always pick door and ignition before trunk , always better locks , less crap gets in them. position 8 is always a 1 cut
Smart don't have any door locks Unfortuantly
Tools owned -
AD100 PRO, Lonsdor, FVDI 18, FVDI 20, VVDI PROG, VVDI2, VVDI MB
CGDI BMW, SuperVag, Renault ECU tool, OBDstar X300 DP Plus, AUTEL im508
VVDI Mini Keytool, KeyDIY KDX2, SBB, ACDP CAS/KVM
Opcom, VCDS pro, Diagbox, Multiecuscan, Forscan, JLR SDD
szengen (26th January, 2020)
of course on the old fourtwo this is the case , the boot lock when turned and held should unlock central locking , fourtwo,fourfour etc blend into 1 as so rarely seen .
Last edited by rapidlocksmiths; 25th January, 2020 at 05:49 PM.
sdnatlst (25th January, 2020)
Hi guys
Having a trouble with smart 2002 locks
Decoded ignition
1 4 1 3 2 4 4
On Instacode and on my Miracle A9 this code doesn’t exist. According to Insta wafers are 5 to 8. So Im not sure what correct code should be in this case
Car is non runner atm so i have few days
Regards
strip ignition,1 minute to do and check wafers
try 58576885 , you wont find a valid code on instacode as instacode doesnt have the code series for this .
if you have used a lishi with values 1234 on the grid then instacode lists the cuts as 5678 , so convert using following table;
1 = 5
2 = 6
3 = 7
4 = 8
position 8 is always a 1 cut so on instacode a 5 .
so
14132441 should cut as 58576885 , hopefully this will give you your correct key
Last edited by rapidlocksmiths; 4th February, 2020 at 01:14 AM.
ghostrider72 (4th February, 2020)
Thanks mate. That worked. Unlucky me - key turns in ignition fine but... now it wont turn back
thats painfull , lock out time me thinks
Not that mate. I have barrel in my hand now. Still wont turn back
Try tapping on the desk line a chocolate orange nothing to loose, its knackered now
Was Banned For Being Certifiably Insane and Stupid
ive not had this on smart , had similar on hyundai when the machine i had at the time cut the tip angle too steep and wafer got jammed behind the cut stopping extraction , i used to hand file the angle on these to make it less harsh , the machines i have now dont suffer the same and cut a better key.
if all else fails torch the car , it would be viewed as a mercy killing
Last edited by rapidlocksmiths; 5th February, 2020 at 12:45 AM.
fred77 (5th June, 2021), ghostrider72 (6th February, 2020), jodge (5th February, 2020), Manta1600 (5th February, 2020)
drill the pin remove spring and safe and it will be apart
ghostrider72 (6th February, 2020)
Bookmarks