Can we get a sticked IPROG china clone mega thread

**teerak2uk** · 10th June, 2021, 05:37 PM

Originally Posted by fuzz1

I can't believe the stupidity of those making clones. Using good parts would make the device reliable. They are fixing on getting the cheapest device not a reliable/working one.

Typical of Chinese clones using cheap or incorrect parts or both

**Jonatanfunes91** · 10th June, 2021, 07:54 PM

Originally Posted by fuzz1

what do you expect to do with the iprog by the way? what is your experience

fuzz friend
I need to cover odometer of VW / said renault ABS by obd2 and some brands of opel .. since with upa I can not do it .. they are the only car that I could not do ..
if not, what do you recommend me friend?

**wembleyhill** · 10th June, 2021, 08:05 PM

Originally Posted by Jonatanfunes91

fuzz friend
I need to cover odometer of VW / said renault ABS by obd2 and some brands of opel .. since with upa I can not do it .. they are the only car that I could not do ..
if not, what do you recommend me friend?

you can't do (VW / said renault ABS by obd2) with iprog

**Jonatanfunes91** · 10th June, 2021, 08:10 PM

Originally Posted by wembleyhill

you can't do (VW / said renault ABS by obd2) with iprog

mmm thanks partner for the information I thought so .. mmm and what device do you advise me to do (ABS dacia / logan fluence etc ..)
REnault
Opel Meriva / Corsa
VW G6 G5

**fuzz1** · 13th June, 2021, 08:27 PM

Hi

Does anyone know what the 4.7 k ohm resistor that is needed to change to get the iprog + working with uart board goes to?I tried to change mine but damaged the pads so now wondering where to connect it to

**fuzz1** · 13th June, 2021, 08:31 PM

Originally Posted by PaulJeepman

Thanks

I have replaced R20 with 51KΩ (513 0603) & R12 with 4.7kΩ (472 0603)

After obtaining fw130sn, Updated via USB. Now I can change Serial No easily.

Hi

I see that you replaced the resistor. Can you please tell me where the resistor is connected to on the board?I found two lines going from the resistor on the board. where does the connection line go to please?
I tried to remove the epoxy on my board and it ripped the lines i can't follow them.

thanks

**fuzz1** · 14th June, 2021, 05:15 PM

Was wondering if supplying 5volts to pin 14 and 12 volts to pin 29 through an external power supply will get the iprog working.

I know it's probably switching the output to those voltages at specific times or will probably destroy the capacitors.

**toyota123** · 14th June, 2021, 08:21 PM

Originally Posted by fuzz1

Was wondering if supplying 5volts to pin 14 and 12 volts to pin 29 through an external power supply will get the iprog working.

I know it's probably switching the output to those voltages at specific times or will probably destroy the capacitors.

hi friend .. donch change if it's not nessecary ... mine is clone , and it works fine ...

**fuzz1** · 15th June, 2021, 03:25 AM

Originally Posted by toyota123

hi friend .. donch change if it's not nessecary ... mine is clone , and it works fine ...

Unfortunately mine doesn't work. Carved out the epoxy to replace the resistor but only eeprom works. The other board no.

I'm wondering if pins 14 and 29 can be supplied with constant voltages. Ok with the addition of pull up resistors

**elektoni** · 21st June, 2021, 11:03 AM

Is there a simple way to test which adapters work on my Iprog clone? The revision of my board is 2020.12.22, no glue or epoxy.
And is it safe to supply 12V to the board?
the EEPROM adapter works.

**fuzz1** · 21st June, 2021, 02:03 PM

Not advisable to connect 12V
Not really necessary
Check if it passes the tests. There are scripts in the iprog but you will have to make some simple board or use a breadboard

**elektoni** · 22nd June, 2021, 08:49 AM

Originally Posted by fuzz1

Not advisable to connect 12V
Not really necessary
Check if it passes the tests. There are scripts in the iprog but you will have to make some simple board or use a breadboard

Thanks! I found it. I'll get some diodes and test it.

Was your test OK? Did you have to change D4 diode or R12 resistor?

**fuzz1** · 22nd June, 2021, 10:19 AM

Originally Posted by elektoni

Thanks! I found it. I'll get some diodes and test it.

Was your test OK? Did you have to change D4 diode or R12 resistor?

Nah mine failed.

Covered with epoxy. So heated it and removed the power board. Now waiting for components to try and fix it

**elektoni** · 23rd June, 2021, 09:24 AM

I changed the R12 resistor to 4.7k, the previous one was 1.5k. I think it helped with some communication problems

Any help on this issue? I am trying to read Motorola MCU 912DG128ACF. I have connected all the 4 wires correctly to the IC and I lifted the RESET leg. When I try to read EEPROM or FLASH the progress bar stops at 12% and nothing else happens. The log says "registered = E01BE4C0", "Errors= 40". I am using script 68HC912DG128A