renolink clio 4 keys

[fcastro1988]

hello, I have renolink 1.87 but I cannot copy a card from a clio 4.
I will post the video.
can someone help me
pcf 7953.
1 step- read pin
2 step connect
3 stage start learning
4 put original key
5 learn key card
6 put new key card
7- learn key card
8 validate


but it does not work. says the card is not recognized

[TERMINATOR1000]

hello, I have renolink 1.87 but I cannot copy a card from a clio 4.
I will post the video.
can someone help me
pcf 7953.
1 step- read pin
2 step connect
3 stage start learning
4 put original key
5 learn key card
6 put new key card
7- learn key card
8 validate


but it does not work. says the card is not recognized

you don't respect learning process !

[fcastro1988]

you don't respect learning process !

can help me ?

[omarino]

Test presence


Envoyé de mon iPhone en utilisant Tapatalk

[p1et]

You must have card from dealer ordered by VIN

[P&D]

I thought Genuine Part Number: 285971998R is PCF7939

Is the card new & unused ?

[fcastro1988]

now I managed to learn the key, but the other one stops working. whenever i put one to work the other for, can you tell me the steps?

1 read pin
2 coonnect
3 start learning
4 ???
5 ???
6 ???


sorry and thanks. is that there is no toturial on the internet

card is new .

[TERMINATOR1000]

now I managed to learn the key, but the other one stops working. whenever i put one to work the other for, can you tell me the steps?

1 read pin
2 coonnect
3 start learning
4 ???
5 ???
6 ???


sorry and thanks. is that there is no toturial on the internet

card is new .

Card is OK , but

with cheap tool is no instruction to use available , no tutorial ....

[omarino]

1 read pin
2 test presence
3 conect


Envoyé de mon iPhone en utilisant Tapatalk

[fcastro1988]

Card is OK , but

with cheap tool is no instruction to use available , no tutorial ....

already got it. I don't know how.
I did the same procedure.
but this time I started to learn, then learn key I entered the original key, then I inserted the other new key and tested presence. did nothing and did it again to learn the key and it appeared at 2. I put the right in both and I removed the keys later I validated. and started to give 2. I don't know how

[fcastro1988]

1 read pin
2 test presence
3 conect


Envoyé de mon iPhone en utilisant Tapatalk

4
5
6
the others steps ? plz

I did it but now I'm curious. as I did.
if you can say all palaces. thanks


* I teach what I know
* learn what others know

[andreia67]

These are the commands and messages for classical key (ex: Logan 2, Sandero 2, Duster):
1. Read PIN PIN READ
2. Connect CONNECTED
3. Start Learning
4. Insert key 1, switch to on (engine) and press "Learn key"; if the key is OK message is "KEY LEARNT OK", if not message is "KEY NOT LEARNT"
5. Insert key 2, switch to on (engine) and press "Learn key"; if the key is OK message is "KEY LEARNT OK", if not message is "KEY NOT LEARNT"
6. Press "Validate"
7. Press "Disconnect"
8. Press "Close"
You need to adjust the procedure for cards.

[matej505]

Hello, I have a problem with the Renolink 1.87 interface.
I wanted to add a second card to Renault Clio 4 and chose Enable Pin code Reading .....
ISK code and PIN code have been read but the only working card has stopped working ....
You can see the ID of the cards after inserting them into the reader, but when you try to learn, the HFM not learning message pops up.
What is going on?Have you had such a problem?

[godfathertre]

I just hope does not need to go to dealer otherwise your cheap renolink 30 euro tool just messed up good luck .

[matej505]

I hope someone has had such a problem here on DK.
HFM 70F3633 I am able to read.