Programmer recomandation
Register
Results 1 to 6 of 6
  1. #1
    Senior Member

    Join Date
    Mar 2019
    Location
    Earth
    Posts
    283
    Thanks
    81
    Thanked 70 Times in 33 Posts
    Downloads
    9
    Uploads
    0

    Default Programmer recomandation

    Hi guys.I m working pretty hard into immo and car electronics lately,i have VVDI Prog,Carprog and Xprog 5.55.Recently xprog died (it reads bad every eeprom) so i m not trusting to work with it .Car prog doesn t have any adapter to solder the eeprom on it and vvdi prog sucks when it comes to eeproms( i had a very bad time writing a 24c02 yesterday) .Can anyone recommend me a good and reliable programmer that works good with eeproms? I was looking at UPA ,and MiniPro .I know orange5 is my way to go but it s a little bit out of buget .Thanks

  2. #2
    Member
    Join Date
    Aug 2015
    Location
    Latvia
    Posts
    59
    Thanks
    5
    Thanked 24 Times in 22 Posts
    Downloads
    52
    Uploads
    0

    Default

    Hi, I have UPA and Minipro for eeproms , booth works good. I always read and write desoldered, it is not difficult, but safe.

  3. The Following User Says Thank You to armi For This Useful Post:

    12manux (23rd March, 2020)

  4. #3
    DK Veteran
    PocketHero's Avatar
    Join Date
    Jun 2017
    Location
    Budapest, Hungary
    Posts
    654
    Thanks
    738
    Thanked 474 Times in 251 Posts
    Downloads
    4
    Uploads
    0

    Default

    Read what I wrote in My Toys (link in signature), after my experience you can't Miss O5. When low on money, buy a chinese version for beginning.
    I had never any kind of troubles with my X-Prog 5.0, try to get an older version.

  5. The Following User Says Thank You to PocketHero For This Useful Post:

    12manux (23rd March, 2020)

  6. #4
    Senior Member

    Join Date
    Mar 2019
    Location
    Earth
    Posts
    283
    Thanks
    81
    Thanked 70 Times in 33 Posts
    Downloads
    9
    Uploads
    0

    Default

    Quote Originally Posted by armi View Post
    Hi, I have UPA and Minipro for eeproms , booth works good. I always read and write desoldered, it is not difficult, but safe.
    I work the same, I never read in circuit, just soldered in board

    Trimis de pe al meu STK-LX1 folosind Tapatalk

  7. #5
    DK Veteran
    garciaefren's Avatar
    Join Date
    Sep 2010
    Location
    colombia
    Posts
    315
    Thanks
    72
    Thanked 55 Times in 19 Posts
    Downloads
    907
    Uploads
    1

    Default

    PROGRAMMER
    GQ 4X

  8. #6
    DK Veteran

    Join Date
    Jun 2010
    Location
    EU Romania
    Posts
    792
    Thanks
    81
    Thanked 133 Times in 94 Posts
    Downloads
    186
    Uploads
    0

    Default

    Depend of the budget you want to spending, I recommend you this UUSP-S (UPA-USB Serial Programmer-S) original from Elrasoft.com http://elrasoft.com/uusps.htm if you don't want to have problems in future, or you can take another programmer from Elnec.com but more expensive.

    For UUSP-S (UPA-USB Serial Programmer-S) I have also nice adapter build by me what work also with old UPA USB programmer what is also good, in my adapter you can solder eeprom or can use in circuit programming ICP eeprom or MCUs, depend of needs.

    This is my adapter.



    Last edited by Seby_TM; 4th April, 2020 at 12:00 AM.

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •