Reply With QuoteCompare for what? That board looks fine.
What is your problem?
Results 1 to 8 of 8
Thread: GMC envoy 2003
-
16th July, 2020, 04:40 AM #1Top Poster
- Join Date
- Oct 2018
- Location
- Jupiter
- Posts
- 185
- Thanks
- 49
- Thanks
- 13
- Thanked in
- 9 Posts
GMC envoy 2003
Hello folks,
Anyone could upload a picture of the back of the connector of a GMC envoy 2004 please.
I need to compare with that one.
Thanks/Merci
Sent from my Pixel 2 XL using Tapatalk
-
16th July, 2020, 04:43 AM #2V.I.P. Member
- Join Date
- Mar 2015
- Location
- Canada
- Posts
- 7,333
- Thanks
- 1,200
- Thanks
- 7,690
- Thanked in
- 4,831 Posts
Last edited by clusters; 16th July, 2020 at 04:46 AM.
Please DO NOT PM me asking for help.
Post in the forum, that is what it is here for.
-
16th July, 2020, 04:48 AM #3Top Poster
- Join Date
- Oct 2018
- Location
- Jupiter
- Posts
- 185
- Thanks
- 49
- Thanks
- 13
- Thanked in
- 9 Posts
It came short to ground with a consumption of 10mA.
Sent from my Pixel 2 XL using Tapatalk
-
16th July, 2020, 04:52 AM #4V.I.P. Member
- Join Date
- Mar 2015
- Location
- Canada
- Posts
- 7,333
- Thanks
- 1,200
- Thanks
- 7,690
- Thanked in
- 4,831 Posts
Well the connector pins are not your problem, and a 10mA draw is not a short to ground.
Post a clear pic of the whole back of the board.Please DO NOT PM me asking for help.
Post in the forum, that is what it is here for.
-
16th July, 2020, 04:56 AM #5Top Poster
- Join Date
- Oct 2018
- Location
- Jupiter
- Posts
- 185
- Thanks
- 49
- Thanks
- 13
- Thanked in
- 9 Posts
Here it is.
Sent from my Pixel 2 XL using Tapatalk
-
16th July, 2020, 05:02 AM #6V.I.P. Member
- Join Date
- Mar 2015
- Location
- Canada
- Posts
- 7,333
- Thanks
- 1,200
- Thanks
- 7,690
- Thanked in
- 4,831 Posts
Not hi res enough.
Look for grey spots around the vias to the ground plane.Please DO NOT PM me asking for help.
Post in the forum, that is what it is here for.
-
16th July, 2020, 05:04 AM #7Top Poster
- Join Date
- Oct 2018
- Location
- Jupiter
- Posts
- 185
- Thanks
- 49
- Thanks
- 13
- Thanked in
- 9 Posts
Ok I will.
Sent from my Pixel 2 XL using Tapatalk
-
16th July, 2020, 01:34 PM #8Top Poster
- Join Date
- Oct 2018
- Location
- Jupiter
- Posts
- 185
- Thanks
- 49
- Thanks
- 13
- Thanked in
- 9 Posts
I fix few via that had corrosion but that didn't help anything.
Possible to have some point of reference on the board so I can check voltage? Maybe with the amount I should get at some area on the board so I can eliminate few areas?
On Q17, Q20 and Q18 I am getting around 9.6 volt on each legs
Thanks/Merci
Sent from my Pixel 2 XL using Tapatalk
Bookmarks