Elrasoft delivery time????

[florinyes]

Have a look in here mate ELRASOFT Products

It sure does..

Ta

[BeianM]

Hi I have been told i require UPA-USB to read/write 908 chip (From Sprinter WSP unit) Is this correct, any advise would be more then welcome, Thanks

I am doing the same for the Espace dash & BII. I bought one from Elrasoft, it arrived in less than a week to the UK. Don't expect to get any help from them though. I have asked 3 times for support on adaptors & have not got a reply.
For me I think it would have been better to have bought the
ETL http://www.etlweb.com/?ref=products_programming_tools version that comes with adaptors. & if you mail them you can negociate on price.
I have ordered a clam type holder for the chip so I don't have to solder it to the adaptor & I see you can get one of these for the ETL.
Can anyone point me in the direction of articles regarding using this with the tacho universal, this would save me removing the chips & would be a great help, Thanks.
I'm off to do some searching about this.

[PremierD]

I am doing the same for the Espace dash & BII. I bought one from Elrasoft, it arrived in less than a week to the UK. Don't expect to get any help from them though. I have asked 3 times for support on adaptors & have not got a reply.
For me I think it would have been better to have bought the
ETL http://www.etlweb.com/?ref=products_programming_tools version that comes with adaptors. & if you mail them you can negociate on price.
I have ordered a clam type holder for the chip so I don't have to solder it to the adaptor & I see you can get one of these for the ETL.
Can anyone point me in the direction of articles regarding using this with the tacho universal, this would save me removing the chips & would be a great help, Thanks.
I'm off to do some searching about this.

First bit of research mate ..should be ..how to remove eeproms, so you don't fcuk them ......

[melcool]

Tacho Universal Clips work....but you have to make your own UPA to TU Clips adapter!
I will make you a picture whit them tomorrow!
......and use your imagination!

Here are the pictures whit the adapters:

[melcool]

As I said ..... use your imagination!

[BeianM]

First bit of research mate ..should be ..how to remove eeproms, so you don't fcuk them ......

Oh I have done plenty of that research that is & I have some boards to destroy. I did get a useful reply from elrasoft today, slow to do so however.

[florinyes]

Did anyone managed to build a box for the programmer? It looks exposed as it is..Elrasoft recommending this too..


Cheers

[maciupiciu]

a good friend of mine put his UPA in a box, here can be seen some pictures

[adam28]

@florinyes
You may want to get some of these too. 7" Female-Female Header Jumper : Store @ CuriousInventor.com

This company are in the US,but i use them a fair bit, with no probs. They have lots of of goodies here!

These are good for putting on the test clips and then to your programmer, and also on the pins of clusters etc. i cant get enough of these little buggers. And also the male type.

Cheers

[BeianM]

@florinyes
You may want to get some of these too. 7" Female-Female Header Jumper : Store @ CuriousInventor.com

This company are in the US,but i use them a fair bit, with no probs. They have lots of of goodies here!

These are good for putting on the test clips and then to your programmer, and also on the pins of clusters etc. i cant get enough of these little buggers. And also the male type.

Cheers

I bought a pack of female crimp pins from Maplin & used insulation tape to wrap them as I couldnt find the small heat shrink. It does the job, not as good as ready made though. Thanks Adam I will keep them in mind.

[Remapking]

Have a look in here mate ELRASOFT Products

It sure does..

Ta

Hi do you know which adaptor i would need to read 908 from merc wsp unit in circuit..

thanks

[BeianM]

The elrasoft that is discussed in this thred is designed to read in circuit. See if your chip is here => ELRASOFT Products

[florinyes]

if you want a diagram of which wire goes where send me a pm and will help you out...

Would you post the pin outs on the forum please. Got my UPs yesterday so within a week. The 3 weeks thing must be to cover them up.

Thanks everyone that had an input.

Best regards

[BeianM]

Would you post the pin outs on the forum please. Got my UPs yesterday so within a week. The 3 weeks thing must be to cover them up.

Thanks everyone that had an input.

Best regards

Did you login to elrasoft & get this? or do you still need it.

[BeianM]

Anyone here had any success with this programmer. I have been trying to read motorolla hc908's. Both on board & off, in a clamshell adaptor. I have not found any usefull help files for their software & tech support tells me to go read a different chip!! If there is a good forum you know of then let me know. I currently have it telling me I have an error of hi reset. Does not matter how many times I have checked the connections & have tried 3 chips. & how do you enter the security bits.
Thanks in advance.
(anyone got a tacho universal they want to rent me?)