Elrasoft delivery time????

**autocargo** · 30th April, 2010, 01:24 PM

Thanks Amine13. I already have that upa-usb pdf file. There is a tread about making your own adapters somewere on forum but since I got this adapter I was curious if someone has it,and if it is easier to work with this one rather than using the DIY adapter described by you. Anyway anybody got an idea about the 10 pins sticking out of this board? I have seen some ready made eeprom soic/clip adapters on ebay that are already wired and they have just the connector that will fit on top of that adapter.

**Amine13** · 30th April, 2010, 02:21 PM

You can do it easily, all you have to do is to save the colors leads and their correspondance with RS232 female terminal; for example, the one I have is :
1: Black
2: brown...
I will try to upload some photos of the components you need to make an adapter from UPA ready to hold the eeprom directly.

**Amine13** · 30th April, 2010, 02:43 PM

As promised here are some photos, all the components are availlable, you can find them easily, maybe for SOP8 adapter, you can get it through internet for less About 1500 Da ( 15?).
Sorry for the colors affectation, is in french. Then you can make just two cables with that, and when you need swiotch from SPI, I2C to Microwire, just unplug SOP8 adapter and put it on the other cable
Best Regards.

**autocargo** · 1st May, 2010, 01:38 PM

Thanks Amine13. I ordered some 8 pin eeprom clip soic,it seems everybody is using them here and will make own leads using the cable you have on pictures. Now back to my adapter

) I managed to find one 24C04 wich successfully read and program and one 24C02 that I mounted on adapter printed pads and secured with a clip my mum uses to hang clothes after washing

) it needed a little extra pressure on the clip to achieve good contact with adapter pads and after that...... read and program successful!! No need to solder then. I've had some good times playing with this adapter. It seems it can be used safely to read and program. Didn't had other eeproms to test so only this two been tested with.

**morfej** · 28th September, 2010, 08:49 AM

hi,

Does anyone managed to pay for UPA at share-it with paypal ?

When I suppose to be redirected to paypal website, just get message that order is delayed and nothing happens.

Share-it support is not helpful

they just suggest to match billing email with paypal account email, but doesn't help either.

Br

**jimthejock** · 29th September, 2010, 10:40 AM

hi there ive used share- it a couple of times to buy upa and it has worked fine, maybe there is a problem with the site at the moment

**morfej** · 29th September, 2010, 10:43 AM

Did you used paypal or wiretransfer ?

I gave up with paypal and used wiretransfer to order UPA.

**jarfm** · 21st October, 2010, 02:29 PM

My programmer arrived after 1 week. I've paid by PayPal. Now I'm waiting for login

**martij976** · 4th November, 2010, 04:17 AM

I received my upa today (Nov-03-10) and waiting for software...
After sending an e-mail to support center, an automatic answer just let me know, that office is closed till nov-05

)
How cute....

**RossK** · 29th August, 2012, 06:05 PM

Why the hell don't they just supply you a login with the device, I am waiting for mine to be delivered, and from the sounds off it, even when it does turn up I might have to wait another week for login, just so I can use it.

Seems to me by reading hundreds of posts that the hardware is good, but apart from that everything else sucks!

**datapage** · 28th September, 2012, 05:32 PM

NEED SOFTWARE UPA USB Device Programmer v1.3.0.14
MY ORIGINAL INTERFACE.
THANKS

**Iggie** · 28th September, 2012, 09:50 PM

In that case log in with your user and pass here: Please log in

**datapage** · 29th September, 2012, 12:02 AM

bought used, do not have a password, I no have the User.
At the time, not sent to Brazil.

**mcm44** · 6th October, 2012, 01:34 PM

If UPA programmer is original, write e-mail to support@elrasoft.com.
If serial number of device is ok, you will get username/password to log in. This version of software (1.3.0.14) have to be activated anyway in Elrasoft...