EDC17 BDM pinout

**elektronik325** · 12th April, 2021, 11:41 AM

Give your friend the ECU number. Then I will see if I have such a set of files.

**marcolr** · 12th April, 2021, 09:25 PM

Originally Posted by elektronik325

Give your friend the ECU number. Then I will see if I have such a set of files.

The data of ecu is 0281032456_1037555072_10SW016308_TC1793.
I have several sets of files readed with ktag for the same ecu number, but I can´t write it in the ecu because ktag can´t comunicate.
The ecu doesn´t have any hardware damage. The problem is that a part of data in the internal flash was erased.
The KTM Bench can identify ecu but can´t write or read anything now and it gives me an error related with password

**gia** · 12th April, 2021, 09:54 PM

unfortunately I do not know come and help you.I only found this
unfortunately I do not know come and help you.I only found this

**elektronik325** · 13th April, 2021, 01:01 PM

Here you have the full ktm reading, try to give him the password manually and upload this set. And then try to change. If it helps you, please give thanks and reputation.

**marcolr** · 14th April, 2021, 12:57 AM

I want to say thanks for all members that try to help me. But I want to give a special THANKS for the member "proel" without his help I never could reach a good final.

Best regards

**gia** · 1st May, 2021, 12:26 PM

Originally Posted by marcolr

I want to say thanks for all members that try to help me. But I want to give a special THANKS for the member "proel" without his help I never could reach a good final.

Best regards

what is the solution to the problem?

Inviato dal mio SM-A307FN utilizzando Tapatalk

**galiza** · 4th May, 2021, 09:34 AM

Hi, i have the same problem. Readed with KTM1.2 (71 module, bench) ok. Then I tried to write and stopped at 2%.
No ktag communication.
Only ktm (53 module, boot) can recognize it but can not write.

Could someone give me some advice? please.

**AUTOUNIT** · 10th May, 2021, 04:10 PM

Hello Friend,

U have the set of ECU EDC17c69 read with KTM ? is a Jeep Renegade 0281031034 .

**TulioPinter** · 10th January, 2023, 10:53 PM

Hi all, I'm new to the forum. I too have the same problem with an edc17c69 Jeep Renegade, I read flash and eeprom with ktm bench but writing the flash stopped at 2%. Now I can't read and write flash with any tool. Can someone help me? Many thanks in advance

**TulioPinter** · 10th January, 2023, 10:57 PM

I also tried to use the new Kess3 by connecting in bench mode and in boot mode but no identification is completed. If I buy the 14P600KT04 bdm adapter could it solve the problem? Does anyone know the pinout of this adapter?

**proel** · 10th January, 2023, 11:16 PM

Do you try to send logs to Oleg ?

**TulioPinter** · 11th January, 2023, 09:09 PM

Here are the flash and eeprom backup files.
Now I can only read and write the eeprom using the ktm bench. The flash is neither read nor written, password error.
I would like to try to read it with kess3 from the bdm port but I need the pinuot of the bdm port because I don't have the p600kt04 adapter.

**ker0sin** · 29th October, 2023, 12:43 AM

Originally Posted by marcolr

Hi,
I need the BDM port pinout for connect a EDC17C60 to a KTAG.
I have bought the 14P600KT04 adapter and the 14P600KT03 cable. But they take several days to arrive and I need to recover an ECU urgently.
Can someone pass me the pinout from the BDM port of the ecu to the DB15 connector of the Ktag and where to connect the boot cable?

Thanks in advance

make all the specified contacts in all three figures
- this reading method works after a short circuit