Corsa D 1.3 CDTI 2008
Register
Page 1 of 2 12 LastLast
Results 1 to 15 of 20
  1. #1
    Newbie
    Join Date
    Oct 2020
    Location
    uk
    Posts
    17
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Corsa D 1.3 CDTI 2008

    Hi guys, long story short
    Iíve got an corsa d 1.3 2008 Z13DTJ ecu water damaged.
    Is there any possibility to change all kit (BCM, ECM, cluster , airbag ecu) with a different ECU kit? My one itís an Magneti Marelli and the other one itís a Bosch. I think the Bosch kit came from the same year corsa d but A13DTC engine..
    Thanks

  2. #2
    Top Poster

    Join Date
    Oct 2018
    Posts
    196
    Thanks
    11
    Thanked 44 Times in 41 Posts

    Default

    Connects to the diagnostic device?

  3. #3
    Newbie
    Join Date
    Oct 2020
    Location
    uk
    Posts
    17
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    No... eeprom on original ECU missing

  4. #4
    Top Poster

    Join Date
    Oct 2018
    Posts
    196
    Thanks
    11
    Thanked 44 Times in 41 Posts

    Default

    You have to buy the same and program the Z13DTJ Opcom

  5. #5
    Top Poster

    Join Date
    Oct 2018
    Posts
    196
    Thanks
    11
    Thanked 44 Times in 41 Posts

    Default

    And there is communication with the car at all, because it should be without an ECU with everything except the engine

  6. #6
    Newbie
    Join Date
    Oct 2020
    Location
    uk
    Posts
    17
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    I just donít understand... Iím not after swapping the ECU, I want to change everything from another working car (bcm, ecm , airbag module, keys, ignition, etc..) why do I need to program anything???

  7. #7
    Top Poster

    Join Date
    Oct 2018
    Posts
    196
    Thanks
    11
    Thanked 44 Times in 41 Posts

    Default

    You need to buy a magneti marelli set as it was with the engine code you had

  8. #8
    Newbie
    Join Date
    Oct 2020
    Location
    uk
    Posts
    17
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    This is what Iím trying to understand, why I need to put exactly the same set?? What exactly will not work??

  9. #9
    Top Poster

    Join Date
    Oct 2018
    Posts
    196
    Thanks
    11
    Thanked 44 Times in 41 Posts

    Default

    You have read this driver once, because you see a resistor that you desolder before reading, it can be in four different places and the car will not start because this is how the installation is done and then there is a different engine power

  10. #10
    Newbie
    Join Date
    Oct 2020
    Location
    uk
    Posts
    17
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Mate, Iím not about to desolder any resistor and not do any readings ...
    Iím just about to CHANGE all components forming the immo system (ecu, bcm, airbag ecu, key, barrel, lock) from another running car...

  11. #11
    DK Veteran

    Join Date
    Aug 2008
    Posts
    1,012
    Thanks
    88
    Thanked 443 Times in 314 Posts

    Default

    then do as said otherwise replace engine too for the same engine that the kit uses

  12. #12
    Member bendy's Avatar
    Join Date
    Mar 2009
    Location
    Essex, UK
    Posts
    80
    Thanks
    108
    Thanked 38 Times in 21 Posts

    Default

    Hi prodbecks,

    You need a matching ECU, your is 13DTJ engine & you get a kit off say, 13DT you may not have 100% running car.
    There are many differences between engine components & the ECU itself depending variant.

    The Bosch kit no good you have Magneti Marelli (Engine code Z13DTJ) & not A13DTC <---Different variant, system.

    Hope that helps you understand better.

    However this ECU is vary easily repaired from water damage, I have never failed yet with this ECU.
    Last edited by bendy; 7th March, 2021 at 01:22 PM.

  13. #13
    DK Veteran

    Join Date
    Aug 2008
    Posts
    1,012
    Thanks
    88
    Thanked 443 Times in 314 Posts

    Default

    depends on the extent of the damage

  14. #14
    Newbie
    Join Date
    Oct 2020
    Location
    uk
    Posts
    17
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Tanks for the info bendy, unfortunately my ecu has no eeprom chip at all, it was missing so no chance to repair it...

  15. #15
    DK Veteran

    Join Date
    Aug 2008
    Posts
    1,012
    Thanks
    88
    Thanked 443 Times in 314 Posts

    Default

    eprom you can replace with a new one then program it to car

 

 
Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •