Fill eeprom dump :
[VAG with NEC MCU + 24C32 inside] - range 0xCA0 - 0xEDF in hex editor with FF FF ..
[VAG with NEC MCU + 24C64 inside] - range 0x13A0 - 0x1450 in hex editor with FF FF
I need to put cluster in service mode my vagpro eeprom reader not working for some reason, can someone change this eeprom to service mode so I can programme the key thanks.
Tools owned: Hammer, Chisel, Crowbar, Punch, Chainsaw, Cutter and Brain!!!
Did you know People will question all the good things they hear about you but believe all the bad without a second thought.
Note:All information given is to be used for educational purposes only and should not be taken seriously.
Fill eeprom dump :
[VAG with NEC MCU + 24C32 inside] - range 0xCA0 - 0xEDF in hex editor with FF FF ..
[VAG with NEC MCU + 24C64 inside] - range 0x13A0 - 0x1450 in hex editor with FF FF
use buttons
antonypaul (11th November, 2022), p1et (13th March, 2022), super jumbe (10th May, 2021)
One more info please, after getting CS & Pincode from service mode do I write back the original chip a bit confused.
Tools owned: Hammer, Chisel, Crowbar, Punch, Chainsaw, Cutter and Brain!!!
Did you know People will question all the good things they hear about you but believe all the bad without a second thought.
Note:All information given is to be used for educational purposes only and should not be taken seriously.
upload original gonfig add key and update
use buttons
super jumbe (11th May, 2021)
Here your Service Mode dump.
Write back to eeprom then plug on car and program your key
If you have FVDI, you can make key on bench direct in to dash.
Be polite. No Thanks + Rep, no HELP!!! Slava Ukcraine. Dead Putler civilians's killers!!!
antonypaul (11th November, 2022), super jumbe (11th May, 2021)
Last week my Smelecom Eeprom Adaptor got burnt out and I am having bad issue to put the eeprom in service mode, the eeprom adapter not cheap aroung $500 I am going to look for another cheap tool to read and write eeprom on board, what do you all think about the Xhorse Mini Prog is it any good mind you this tool will not automaticaly change eeprom to service mode smelecom does.
EEPROM-ADAPTER.jpg
Smelecom_VagProg.jpg
Tools owned: Hammer, Chisel, Crowbar, Punch, Chainsaw, Cutter and Brain!!!
Did you know People will question all the good things they hear about you but believe all the bad without a second thought.
Note:All information given is to be used for educational purposes only and should not be taken seriously.
For eeprom, i have many can do: UPA, Orange, Iprog, VVdi prog, Carprog, TL886.
TL886 is most used. This job take around 30mn on bench.
If you do on car, do not forget to save ABS coding first.
Last edited by lion0304; 11th May, 2021 at 10:54 AM.
Be polite. No Thanks + Rep, no HELP!!! Slava Ukcraine. Dead Putler civilians's killers!!!
antonypaul (11th November, 2022)
Hello.If you don't want to deal with the soldering business, Miniprog is more suitable for you.
How many topics you want open for the same car?
When I help you
PUSH on +THANKS and REP or
you are right p1et i already use zedfull vvdiprog vvdi2 devices. just because it was asked, I wanted to specify.
p1et (11th May, 2021)
I know friend, I know
musti418 (12th May, 2021)
Bookmarks