XPROG M USAGE

[florinyes]

I'm sorry but I can't find drivers seaching the forum. If I search "x-prog-m drivers" only this post appears, and if I search "drivers" thousands of posts....

Help will be apreciated.

Tomorrow I'll get back to work and I'll upload full cd mate.

[bram380]

I'm sorry but I can't find drivers seaching the forum. If I search "x-prog-m drivers" only this post appears, and if I search "drivers" thousands of posts....

Help will be apreciated.

This is xprog-m driver

[pirilla]

Problem solved.
Now I can read/write 93C46.
Tomorrow I will test with MCUs, but obviously programmer is working OK.

Thank you all !!!!

[wael_sukr]

Hi, its my first post in this very well setup forum so straight to the subject.
I just got my original xprog m but unfortunately i didnt find in the box any usefull pictures showing how to use the programer, how to connect it to the turget mcu, actually i bought it just with the bdm adptor for using it to read eeprom from ews4 and cas modules. I know i should have asked the manufacturer for these pictures and informations but the truth is i am so excitet i cant wait. However sooner or later tmt will answer but i do have a spare ews4 in my workshop that i would like to know how to do it yesterday.
I hope i didnt upset some one with my post.
Regards
Marinos

i use xprog any question please ask
when you select the device there is connection poton help you to connect this device to xprog

[parapilot]

anyone get EWS3 Kline to work? Im struggling, all i get is a flashing green light, and initilising.. iv got 15v power to. Clone btw.

[mexanico1971]

Hi peaple ! thas anyone knows how to make the connections to 374 , 104 pins to x-prog divice ! and what usb- com shold y put x-prog 1 or 2 because whem i install the soft apears in (com 7) and at baud ! 9600, or mor ?!
thanks in advanced ?
regards !

[locks85]

Hi i did one 2L86D in the past, now i am trying my second one and when i press read i get DEVICE SILENT.
Please help

[locks85]

So i did it, problem was with the drivers, i dont know why but i just had to reinstall them. Remember i am using the original tool just for reference.
Regards
locks85

[hamza338]

Problem solved.
Now I can read/write 93C46.
Tomorrow I will test with MCUs, but obviously programmer is working OK.

Thank you all !!!!

hi m8.

can you let me know how are you managed to read 93c46 because i have the same prob with this message device is silent.

thanks.

[Fallen]

I had a lot of issues with "device is silent" when reading large MCU's, I was powering it externaly with a 12v 1.5 amp power supply.
I swapped it to a 19v 3.4amp power supply off my laptop and it worked 100%.

[cqae]

do you do that even when the software says it wants a 15v power supply fallen?

By the way, I just used your tms370 guide, it was very helpful, so thanks!

[Fallen]

Mate, I didn't have a 15v power supply handy, I figured a few axtra volts wouldnt hurt right...
I bet it even made it work faster!

Glad to help mate.

[xito]

I have XPROG 4.5 M with Atmega64 damaged how can I copy the ATMEGA64?

Thanks to all

[gtmech]

hi m8.

can you let me know how are you managed to read 93c46 because i have the same prob with this message device is silent.

thanks.

Get a UPA Programmer aswell buddy.

UPA is perfect for 93c46 where as X Prog-m is perfect for other types of chips like 2D47J. The UPA has the adaptor board for the 93C46, just solder it on and plug it in and your done, X Prog is not so easy with the 93c46.

Its best to always have a UPA and a X Prog-m.