Hi try to reset starter interlock?
Hi,
I have a BMW 120D from 2009.
The car start only when bypassing the starter with ignition on. No fault codes beside Transponder key wich i believe is key reader.
I will have that changed later on but could that cause no start issue ? Ignition goes on but no signal to starter if not bypassed.
EEPROM of cas might be corrupt as well is another idea ?
File is attached just in case.
Happen to anyone before ? Starter was giving strong spark so it seems the starter is good but I might be wrong and the problem is from it.
Best regards,
DeLuXe
Sharing is carying. Please press Thanks + Rep Button if my post is helpful
Hi try to reset starter interlock?
00 06 13 (922)
Sometimes the engine cannot be started
E60, E61, E63, E64, E70, E81, E87, E90, E91, E92, E93, R56
Description of the situation
Vehicle status - pin R.
After depressing the clutch pedal (in vehicles with a manual transmission) or the brake pedal (in vehicles with an automatic transmission) and pressing the START-STOP button, the engine will not start. Instead, the vehicle goes to pin 0 status.
With the clutch pedal depressed or the brake pedal depressed, the customer must press the START-STOP button again to start the engine.
Event
There are no faults. The characteristic is due to the design.
Prerequisite for starting the engine: the clutch pedal (in vehicles with a manual transmission) or the brake pedal (in vehicles with an automatic transmission) is fully depressed (squeezed out).
The pedal must be fully depressed at least 0.3 seconds before pressing the START-STOP button.
This 0.3 second (300 ms) is used as a signal settling time to accurately recognize the engine start intent.
If the START-STOP button is pressed before the signal stabilization time of 0.3 seconds has elapsed, the vehicle enters the status of terminal 0.
111.jpgВот что я предлагаю.. Я не вижу VIN. Схемы не знаю. (((.Может кто-то блокирует запуск.Например коробка не в Р..Перед лечением нужно сделать анализы и все Рассказать о машине,иначе не исправишь..
Here's what I'm suggesting.. I can't see the VIN. I don't know the diagram. (((. Maybe someone is blocking the launch. For example, the box is not in R .. Before treatment, you need to do tests and tell everything about the car, otherwise you won’t fix it ..
I constantly edit messages, the browser translates itself without me and saves. Remind me if it's not clear.
Last edited by Fibiana; 16th August, 2022 at 10:23 PM.
Well the EEPROM + flash of CAS seem to be just fine.
I even replaced the start/stop button and no change. Can't really put my finger on what is wrong and why it doesn't want to start, only by bypassing the starter it fires up with no issues.
Thanks for the help
Best regards
DeLuXe
I don’t understand, is the car on mechanics or AT? The unit, if it does not see the clutch pedal or parking, will not allow the car to start.
VIN?????
Car is manual not automatic Sorry forgot to write the VIN: WBAUD910X0PZ06024
I am misstaken, car is 2007-2008 not 2009.
Best regards,
DeLuXe
Sharing is carying. Please press Thanks + Rep Button if my post is helpful
00 06 13 (922)
Sometimes the engine cannot be started
E60, E61, E63, E64, E70, E81, E87, E90, E91, E92, E93, R56
Description of the situation
Vehicle status - pin R.
After depressing the clutch pedal (in vehicles with a manual transmission) or the brake pedal (in vehicles with an automatic transmission) and pressing the START-STOP button, the engine will not start. Instead, the vehicle goes to the status of pin 0.
With the clutch pedaldepressed or the brake pedal depressed, the customer must press the START-STOP button again to start the engine.
Event
There are no faults. The characteristic is due to the design.
A prerequisite for starting the engine: the clutch pedal (in vehicles with a manual transmission) or the brake pedal (in vehicles with an automatic transmission) is fully depressed (squeezed out).
The pedal must be fully depressed at least 0.3 seconds before pressing the START-STOP button.
This 0.3 second (300 ms) is used as a signal settling time to accurately recognize the engine start intent.
If the START-STOP button is pressed before the signal stabilization time of 0.3 seconds has elapsed, the vehicle enters the status of terminal 0.
sponsored links
Last edited by Fibiana; 17th August, 2022 at 07:16 PM.
Контакт R
Attachment 907104
17.08.jpg
Last edited by Fibiana; 17th August, 2022 at 07:24 PM.
I have ordered another starter and will in same time as changing will check the signal wire or the smal wire going to starter.
I dont know but i feel somehow the starter solenoid is bad perhaps.
Thanks for the help !
Best regards,
DeLuXe
Sharing is carying. Please press Thanks + Rep Button if my post is helpful
It's simple. We take a 12V light bulb and connect it to the terminal. If the light bulb is on, then you need to run to the store. But if not .... then turn on the head.
In ncs , you can turn off the option to press pedal when starting, so you just have to insert fob and press button
Bookmarks