Help Iveco daily BSI Configuration swap

[incutto88]

Hi
I have Iveco Daily 2007 with

MCU: 70F3238
Eeprom: 95320

I need help to clone it in new body buy in virgin state , if I swap eeprom contect not work ,the dashboard no work and the vehicle not start

the original body computer was catching fire and damaged many tracks and components on the board

Someone can swap configuration from old body to new?
Pin vin,exc
I have read, that in the eeprom 95320 there is an identifier number synchronized with the mcu

[kiszka]

Hi
I have Iveco Daily 2007 with

MCU: 70F3238
Eeprom: 95320

I need help to clone it in new body buy in virgin state , if I swap eeprom contect not work ,the dashboard no work and the vehicle not start

the original body computer was catching fire and damaged many tracks and components on the board

Someone can swap configuration from old body to new?
Pin vin,exc
I have read, that in the eeprom 95320 there is an identifier number synchronized with the mcu

the new bcm eeprom is broken or virgin

[incutto88]

the new bcm eeprom is broken or virgin

she is a virgin, the body was bought at iveco
the id identifier from mcu is the select 3 byte in pic?
in my opinion this is the problem, the mcu is not synchronized with the eepromcompare ori new.jpg

[kiszka]

she is a virgin, the body was bought at iveco
the id identifier from mcu is the select 3 byte in pic?
in my opinion this is the problem, the mcu is not synchronized with the eeprom

these are two different BCMs, I think that no one can transfer the entire vehicle configuration here, the immo data alone could be transferred but if the BCM would be configured
it remains to configure the whole vehicle with the diagnostic program after OBD
then programming immo using
pin pin is 56478

[greyg]

You have an incompatibility sw MCU <> EEP.

This can be done without any problems. HW is compliant.
It takes work time.

[incutto88]

these are two different BCMs, I think that no one can transfer the entire vehicle configuration here, the immo data alone could be transferred but if the BCM would be configured
it remains to configure the whole vehicle with the diagnostic program after OBD
then programming immo using
pin pin is 56478

with the new body computer mounted everything works except that the vehicle does not start, it would be enough for me that the immo data from the old eeprom have passed on the new eeprom,
what do you recommend to configure the entire vehicle?
thanks for the help you are giving me

[incutto88]

Hai un'incompatibilità sw MCU <> EEP.

Questo può essere fatto senza problemi. HW è conforme.
Ci vuole tempo di lavoro.

hello teach me? thank you

[kiszka]

hello teach me? thank you

check if this file is working properly
https://mega.nz/file/RvxSFZja

[incutto88]

check if this file is working properly
https://mega.nz/file/RvxSFZja

if it works, I will pay you for the time you are dedicating to me

[incutto88]

check if this file is working properly
https://mega.nz/file/RvxSFZja

Partial working after flash you file ,dashboard all ok,radio display code request, remote key fob only flash the hazard light ,after lock button press the all door remains open, in diag remain blank PIC VAN AND code configuration 20221023_134759.jpg

[kiszka]

Partial working after flash you file ,dashboard all ok,radio display code request, remote key fob only flash the hazard light ,after lock button press the all door remains open, in diag remain blank PIC VAN AND code configuration

check if this file is working properly
https://mega.nz/file/YvB0UYoJ

[incutto88]

check if this file is working properly
https://mega.nz/file/YvB0UYoJ

incutto88 has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

Ok resend link