deegee7456 (27th September, 2013), gohjh48 (2nd August, 2013)
DM800 Flashing firmware by Browser
Flashing a new firmware by Browser
What you need to flash
You need the image file you want to flash. Image files have the extension *.nfi. You can't flash other
images like *.img files. Don't try it - it won't work.
You need either a DHCP server, a configured bootloader or a serial cable and a terminal program
like HyperTerm.
You need a browser, and a network cable. If you connect the Dreambox directly to the PC,
you need a cross cable, if you connect trough a switch/hub/router you need a normal
(non-cross) cable.
To flash a new image, you can use the second stage loader. It must be present and not broken.
The following steps assume you have a DHCP server.
If you don't have one, you have to setup an IP address in the bootloader's serial setup.
--------------------------------------------------------------------------
- Power down the Dreambox, either using "shutdown" and by removing the power connector.
Standby is not enough!
[IMG][/IMG]
- (1.) Press and hold the power button. Replug the power connector into the Dreambox.
- (3.) A text "*** STOP ***" should appear. Now you can release the button.
The bootloader entered the "waiting" mode.
- (4.) Above the "*** STOP ***" text, there should appear an IP-address
(four decimal values with a dot in between). If there appears the string "dhcp" instead,
the box still searches for a DHCP server. Wait a bit. If it doesn't change, something doesn't
work with the DHCP server. Check wether network cable is plugged in etc. If it just doesn't
work, set an IP using the serial terminal
[IMG][/IMG]
Now, open a browser on your PC.
(1.) enter in the address line "http://ip/" (where ip must be replaced with the value in the LCD).
- (2.) on the bottom of the page, there's a link called "firmware upgrade". Click it.
On the next page, you can select the flash image you want to flash. be sure that it has the ".nfi" extension.
You can't flash other images (like .img)!
- Click on "FLASH!" and wait. It might take some time to upload and flash the image.
- Switch the box off again, and on again. The new image should be flashed and working.
dm800-s=1.1 m triax motorised dish=titanium twin lnb
DIGITAL KAOS BEST SITE ON THE NET
please use the thanks button if someone has helped
deegee7456 (27th September, 2013), gohjh48 (2nd August, 2013)
i am not sure if i mentioned that i was looking for the flash for the dm800c hd to get it working once again thanks
can i do the some on a DM600?
how to do a backup of image from the box?
thks
Thanks for the instructions, flashed my dm800c successfully.
Last edited by gps777; 26th May, 2010 at 04:32 AM. Reason: information updated
Hi, I have just flash my HD800 with PLI image but got this message>Error: No CA Found
Anyone can help? How do I flash a new image? Can I use Dreamup?
Last edited by Louiz; 12th August, 2010 at 09:27 PM.
THE TRUTH
The Hillsborough Independent Panel. 12/09/12
Today's report is black and white.The Liverpool fans were not the cause of the disaster.
The panel has quite simply found 'no evidence' in support of allegations of 'exceptional levels of drunkenness, ticketlessness or violence among Liverpool fans' and 'no evidence that fans had conspired to arrive late at the stadium' and 'no evidence that they stole from the dead and dying'.
But my dreamup cant connect to my HD800. No respone from my box when using dreamup
It works on my dm800
How do i do backup for dm800hd?
I
Last edited by Kango; 13th September, 2010 at 06:05 PM.
Hi Bro, I try to Flashing firmware by Browser on my DM800-Cable tuner
On my Dreambox WebControl there is no link called "firmware upgrade" link at the bottom corner .
Currently my dreambox using original image GP2 from the clone box that i bought from China.
Please help & advice,
Bookmarks