VAG-COM/VCDS EVERYTHING

[stefaudio]

hi guis sorry for delay i post pic. of mi old china interface is from first china clones wit FT232BM chip

HELP PLEASE interface work but lost conections in time of diagnose of car
First i use 11.2 beta and all ok but i reprogram atmega wit 11.11.0 dump and after that problem
Now i downgrade to 11.2 again but problem remain

[mishu_b]

Do you know whats the pinout on the h/w is I.e. reset, gnd, msio etc for connection to atmega162

for hw you need to check your ISP connection pinout.

as a hint - most of the tools have similar pinout, you can see the bibkare post for it.

br

[mladen76]

hi guis sorry for delay i post pic. of mi old china interface is from first china clones wit FT232BM chip

HELP PLEASE interface work but lost conections in time of diagnose of car
First i use 11.2 beta and all ok but i reprogram atmega wit 11.11.0 dump and after that problem
Now i downgrade to 11.2 again but problem remain

You coud maybe check all conections to see there are no any lose end,I do not belive that dupm have any relation whit that couse whit 11.11 dupm you can use all previous original installers couse seams that 11.11 VCDS have some bugs.
Check conestions whit multimeter,yust a tought.

[liviudiaconu]

[...]
First i use 11.2 beta and all ok but i reprogram atmega wit 11.11.0 dump and after that problem
Now i downgrade to 11.2 again but problem remain

Can you post here printscreen with the test page? Of course, with VCDS power on or in a car..

What programmer use? what soft for this?

[stefaudio]

Hi frends mi hardware is ok after i resolder all components inside.

Thanks for good ideas regars Stefan

[teerak2uk]

Yes that's right
In all AVR programmers the pins in ISP are the same
And BTW use Extreme Burnet it is much easy to use.
mishub it is specialist and he can use Khazama because he knows to use with it, but one who start in this must use something much easy as Extreme Burner.
After you'll use it you'll see that you'll dosen't want to use anythingelse
Good luck

Do you know what the fuse bits/settings should be in extreme burner


many thanks

[teerak2uk]

Here is dump for flash end eeprom of atmega.I use avr910 programmer,no need to remuve noting.

what about these settings?

[meteor80]

Hello.
Maybe someone have dump for my interface.
It was 11.11.3.
Interface without GAL
Is there any dump that will work with this interface?

[mattydr67]

Hello.
Maybe someone have dump for my interface.
It was 11.11.3.
Interface without GAL
Is there any dump that will work with this interface?

Chinese dump for cracked softwera and use a RL tool....Hmmmmm
I don't think so
Anyway that softwear it is "full of bugs" Bad cracked as all Chinese craked softwear i ever seen
Try to use VCDS 11.11.0 dump and you'll smile
But mate we talking many times here...DO NOT USE INTERNET CONECTION IN COMPUTER WHERE YOU HAVE VCDS SOFTWEAR INSTALLED
otherwise this are the consequences.....you'll have an erased Atmega sooner or later.
Good luck

[mattydr67]

what about these settings?

WRONG!
We talked many times about this and security bits was shared many times here.
Good luck

[teerak2uk]

WRONG!
We talked many times about this and security bits was shared many times here.
Good luck

I know its wrong I've not changed anything but looking at some screenshots from ponyprog but the layout is different

[bibkare]

I know its wrong I've not changed anything but looking at some screenshots from ponyprog but the layout is different

Enter fuse settings from Ponyprog here and you will get settings for extreme burner Engbedded AVR Fuse Calculator

[papjack]

Question to the specialists, is there any way to use a FT232R Cable with VCDS 10 or higher ? Except VCDS Lite...

[mexanico1971]

...

use this one

regards

thank"s mishu but I allready have try width this soft !

the guy o sold me the avr jtag say it work"s width avr studio but I dont find at162 in the sw !
I gona left the lin"k to the sw if someone want !

thank"s

AVR Studio 4, 5 and 6 download links

[mattydr67]

Question to the specialists, is there any way to use a FT232R Cable with VCDS 10 or higher ? Except VCDS Lite...

I suppose that you call "a FT232R cable a VAG 409 kkl", the answear it is NO
Good luck