VAG-COM/VCDS EVERYTHING

**Multipla** · 2nd December, 2014, 02:43 AM

Can you hel me, please? Can give me a ept of 409.1 hi lost a file of my cable and dont work. Please.

**liviudiaconu** · 2nd December, 2014, 02:22 PM

409.1 is a usb to serial converter..

**Multipla** · 2nd December, 2014, 10:40 PM

Yes, but you have file bin or Hex ( ept) of this cable? Vag 409.1 please

**1 6 D** · 2nd December, 2014, 11:56 PM

I need ept file for KKL interface too.

**liviudiaconu** · 3rd December, 2014, 12:25 PM

Attachment 288955

FT232BL? haven't memory, so no need ept, is by default 0403 6001.
FT232RL?
Mprog-> new ->...Device type = FT232R..save as..

See in attach, are the files "by default" from FTDI.
Every new FTDI 232 BM (without external memory) or 232Rx arrive with this parameters..VID 0403 PID 6001 =USB to Serial

In yours cables must install driver from FTDI like serial adapter and made correlation between COM_y from interface with the same COM_y from (VCDSLite or VAG 409)->Options->PORT..
Is recommended to choose COM1 to VAG and realocate COM1 for Serial converter.

Device manager -> Ports-> COM_z (assigned to FTDI) -> Port settings -> Advanced-> port number...Com1 (can be in use..) ok-ok-ok...yess..etc to all questions..

Like here:How To: Getting that eBay cable to work! - TDIClub Forums

That if your device is with FT232.

If not you need another driver:Attachment 288960

**Multipla** · 4th December, 2014, 12:05 AM

TKS all comunity in particular mode liviudiaconu.

**andrey_brest** · 18th December, 2014, 12:25 AM

Originally Posted by liviudiaconu

For your device must desolder IC8, D7, R50, R51.
Reroute 3 wires and reprogramm Atmega, Gal, FTDI.

Is named "Aminebot's tutorial".

desolder IC8, D7 and reprogramm Atmega, FTDI...

---
Hello everyone.
I'm back...

**zodiname** · 27th December, 2014, 08:46 PM

I have problem with 12.12 ,
if I plug to usb and get port test then like foto 1 but if connect to 12v then like photo 2

please help ?

**teerak2uk** · 28th December, 2014, 12:41 PM

Originally Posted by zodiname

I have problem with 12.12 ,
if I plug to usb and get port test then like foto 1 but if connect to 12v then like photo 2

please help ?

I had this but installed a different 12.12 from the net and it worked

**zodiname** · 29th December, 2014, 08:14 PM

Can I reflash this (12.12 pcb photo) with old firmware1.810- 10.6 , 1.84 - 11.11 ?

**liviudiaconu** · 30th December, 2014, 07:05 AM

Yes, is possible. Fw+Eeprom

**Pardul** · 2nd January, 2015, 06:58 AM

how set lockibt and fusebits in upa to program atmega ?

**art64** · 3rd January, 2015, 12:09 PM

Hello DK,
I have old VCds cable from China version 8.214 and something is wrong with it. If I connecting the cable to the car without CAN everything goes OK,but if I do connect to the car with CAN (example Touran 2004) program hangs on and after while I have a note: The cable not find... Does anybody know which chip refusing to work properly? Thank you

**liviudiaconu** · 3rd January, 2015, 07:11 PM

@pardul: try to read the fusebit and lockbits from atmega first... after write atmega with readed bits.
@art64: do a test with interface only powered (connect only pin 16=+12V and 4-5 =GND).
In in Option-Test appear K1-2=OK, CAN OK...can chips can be defective.
If not...can be old version=>try rewrite with 11.11.0 dump and use VCDS 11.11.0

My oppinion is the interface is erased or older version...

**art64** · 4th January, 2015, 06:54 AM

Originally Posted by liviudiaconu

@art64: do a test with interface only powered (connect only pin 16=+12V and 4-5 =GND).
In in Option-Test appear K1-2=OK, CAN OK...can chips can be defective.
If not...can be old version=>try rewrite with 11.11.0 dump and use VCDS 11.11.0

My oppinion is the interface is erased or older version...

If I do connect only
pin 16=+12V and 4-5 =GND,everything goes OK - I wrote about it. And the CAN can't be OK in this case.( In this case: K1 -OK, K2-OK, CAN -not ready) But if I will do connect to the car equipped with the CAN , another message appears: "the Ros s tech cable did not find...." It can't be old version,because failure occurs suddenly a few years ago then I did connect to some one Audi. I bought a newest version 12.10,but the old version is better sometimes. The new cable do not ecu and immo swapping in immo 3 system. So I dream fix the older cable.