VAG-COM/VCDS EVERYTHING

**hid3** · 13th September, 2018, 05:27 PM

Use VAGCOM_EEWriteLang.exe executable which is located in the kolimer's archive.
Flash English language.
Use the loader provided in the same package too (I'd suggest doing a clean reinstall of the software to be sure). Be sure to use the VCDS Original installer (not the one from the Panda CD) - links to it can be found somewhere in this thread.

If after doing the above steps you still face the same problem - report back.

**Erikol** · 14th September, 2018, 12:02 AM

Originally Posted by belkor

ok...glad to hear that
now you are to program atmega chip.... for that you need an USBASP programmer and follow pdf instructions.....or other programmer

Just tried to solder de wires required to program with USBASP, but i think i fried MCP2515. pin 18 and 17 are not meant to be short on eachother i suppose? Cleaned all solder but short between those two stays...so thinking i overheated and short it inside...

Can i try to replace the IC? I see them voor 2€ online..
If this not going to be succesfull... i believe the following cable is the best buy for the moment? :

http://www.obd2cartool.com/atmega-va...t-skoda-p-1492

**Casanoaa** · 14th September, 2018, 08:59 AM

Hid same happens.

Sent from my iPhone using Tapatalk

**alexm1** · 14th September, 2018, 09:23 AM

Find another car with similar NAVI and try to connect, if the module is opened, the cable is ok, but your car has a problem ...

**hid3** · 14th September, 2018, 12:32 PM

Really interesting...
If you go to Autoscan, then "Gateway installation list" -> does it list 37 - Navigation there? What's its status there?

**Casanoaa** · 14th September, 2018, 01:11 PM

Yes see here:

Sent from my iPhone using Tapatalk

**kaalis** · 14th September, 2018, 01:20 PM

#37 Not registered could be connected with faults in #56 radio.
https://forums.ross-tech.com/showthr...orrectly-coded

**Casanoaa** · 14th September, 2018, 02:50 PM

Guys i have good news. I Can now enter it. I took navigation out, all wires out and installed the navi again. Therenext i could Enter the menu. Now it shows malfunction in gateway list but it works.

Sent from my iPhone using Tapatalk

**helios4stars** · 14th September, 2018, 09:37 PM

Hello,

I have an old interface, 12.12, I would like to update it to be able to use newer VCDS versions, can someone guide me on what do I have to do? I'm attaching some pictures of the interface maybe it helps.

UNADJUSTEDNONRAW_thumb_504a.jpg
UNADJUSTEDNONRAW_thumb_5049.jpg

**alexm1** · 14th September, 2018, 09:41 PM

This type of cable will not work to update, has no Atmega, you have NEC=CHINA...buy another with Atmega.

**Jerak** · 14th September, 2018, 11:53 PM

My clone came today.
It came with all the suggested parts but instead of a ATA6561 I got a NXP A1050/C.
All good?

**pablobrsp** · 14th September, 2018, 11:58 PM

Dearsss...

Enclosed my clone interface dead. I have an USBASP programmer and I now how to use it, but I need the files to update to 18.2.

Sure, its an Atmega controller.

Dos someone can guide me how to?

Tks in advanced.

20180914_195150.jpg

20180914_195156.jpg

**pablobrsp** · 15th September, 2018, 01:18 AM

Deleted post

**pablobrsp** · 15th September, 2018, 01:22 AM

Originally Posted by alexm1

Hi,
anyone can help with Interface programming pinout ? For connecting to Uspasp prog.
Mosi, MISO. SCK RESET.

Pic below.

Thanks

L.E. - this is hex V2.

HI Alex, I have the same HW and after some days it stop work. Have you ever finished your update? My interface was running 18.2 version and now is blocked.

Would be great if you assist me how did you do.

Thanks a lot,

BR

Pablo

**alexm1** · 15th September, 2018, 07:53 AM

First, download files from here

https://www.sendspace.com/file/em3y1f

Read Info pdf inside the zip, if you have usbasp programmer, find pinout
-solder those 4 wires to your pcb

If you never did that, take some time to read this thread and you get all the info you need to do your job.