VAG-COM/VCDS EVERYTHING

[whatispro]

Hello again,

It’ working correctly now.

Thanks !

[igt]

Hi.
I have this cable . Vcds 18.2.1 and i have multiple rod file missing error .. so cable is pratically unusable.

What kind of chip does it have ?
Is it upgradable ?


Thanks

[sahraoui1]

Hi ,reflashe thé câble , it will be ok

[Tyrex]

Hello. This interface can be repaired? Now its not connecting to CAN due a firmware upgrade from official web site (stupid i know). Thx. P.S. IMAG1024.jpgIMAG1028.jpgP.S. Now i see a modification inside with this red cable. This is a SH interface.

[kaalis]

Hi ,reflashe thé câble , it will be ok

where do you see atmega162?

[hid3]

Wrong message

[networkers]

Hi,

Hello. This interface can be repaired?

what is happened to this interface? Bad soldering, maybe short circuit.

Throw it away and buy a new one!

[pocinas]

Hello. This interface can be repaired? Now its not connecting to CAN due a firmware upgrade from official web site (stupid i know). Thx. P.S. IMAG1024.jpgIMAG1028.jpgP.S. Now i see a modification inside with this red cable. This is a SH interface.

On the 2nd photo right side Yellow element, capacitor....resolder in correct possition

1st photo. Chip from right side. Pin 20 and 21 have short... it is correct?

[Tyrex]

I allready buy a new Hex v2 18.9. This old one i try to repair-it just for my curiosity. Bad soldering on old interface is not my work, i buy-it like that.

[igt]

where do you see atmega162?

So ? i dont understand...
Is it flashable or not ? And primary ...Is there a solution to Rod files missing error to keep it in life ?

[networkers]

Is it flashable or not

No, it is not updatable, because it has an ARM microcontroller (with non public china firmware inside) instead of Atmega162.
The best part is: The case incl. torx screws :-)

[asd2000]

Yes, same here. Seems to work fine!

hi.... work with orignal DRV Version ? wich version u using ?

my cable works now with 18.2.1 DRV and Loader 7.2

[razvan2003]

I have a 10.6 vcds cable.
I unscrewed it and it's an atmega162V.
I removed STC chip.
I soldered PINS from tutorials from above 100% correctly, i checked twice with multimeter. I gave 12V voltage and the LED stays green, or when i dont it blinks red.
I have a USBASP V2 LC Technology.
And when i want to program, progisp says "chip enable program error" on both cases.
I tried a lot of drivers and still nothing.

Photo with PCB: https://imgur.com/a/4zPAdpP

Thank you for your time!

[Roma77]

I have a 10.6 vcds cable.
I unscrewed it and it's an atmega162V.
I removed STC chip.
I soldered PINS from tutorials from above 100% correctly, i checked twice with multimeter. I gave 12V voltage and the LED stays green, or when i dont it blinks red.
I have a USBASP V2 LC Technology.
And when i want to program, progisp says "chip enable program error" on both cases.
I tried a lot of drivers and still nothing.

Photo with PCB: https://imgur.com/a/4zPAdpP

Thank you for your time!

If you are 100% sure that you are doing everything correctly and you have called up all the contacts and cable at the moment, then the worker thinks that it is erased with ID 1E: 94: 04 on FF FF FF, now it needs to be desoldered and restored through JTAG.

[macwol01]

Hi Lads

Just updated my cable to Kolimer 7.2.

Can i run VCDS 18.9.1 with 7.2 ?

Is there a test i can run on the cable to check if long coding will work before i actually try ?

thanks