some ppl with ARM had luck with this loader dose not work for my version arm let me no if it works for u
https://mega.nz/file/H8Z0EAaR#QxNoVG...VMo1bxGweMLyQc
some ppl with ARM had luck with this loader dose not work for my version arm let me no if it works for u
https://mega.nz/file/H8Z0EAaR#QxNoVG...VMo1bxGweMLyQc
Your link is the English latest version. Kaalis said the France (FRM) version is released.
2xded (17th August, 2020)
Yes, tested with french version (FRM)
Hi! I'm pretty much a newbie and I have been putting off buying a diagnostics cable for far too long and I think now it's time...
I have a few questions, because I almost fell asleep while reading the first 5 pages of this thread:
1. Will the cables from the OBD2cartool DK members VIP offer (https://www.obd2cartool.com/vip-link...tubt40p5prjok5) work "perfectly" (like an original Ross-Tech cable) on a MY2000 car?
2. If yes, then is the difference between Option 1 and Option 2 in the above-mentioned offer purely aesthetic or are they different internally?
3. If I bought one of them, would I eventually be able to use it when a new version of VCDS releases?
4. Would it have the exact same features as an original cable or will it be cut-down in terms of features?
Thanks for taking you time, have a wonderful day.
I am on the same page. New to this with vag-com . I have ELM327 and eobd1266 and kwp2000+ and op-com and scantool.net obd-link "BT" adapter
But after a bit of reading I realized this adapters seams not to going to work.
Try to read on the thread to find a good starting point to get understanding of this vcdl and vag-com.
If someone can be kind to point me in right direction on this journey.
Skickat från min SM-G973F via Tapatalk
I'm searching for the 20.4.x of CZ (SVO) of our beloved program but I cannot download it from the official CZ site.
If anybody have it, please share it with me Thanks!
Hi, here is the download.
V 2020 CZ
https://ulozto.sk/file/18dx6UB3prRk/...x-2020-4-1-rar
Last edited by western6089; 26th August, 2020 at 08:09 PM.
20.4.2 RUS released
miouser (27th August, 2020)
Hi i have https://www.obd2cartool.com/vip-link...86o4so84i9m7r7
And Kilomers 9.2 and VCDS 19.6.2 is it safe for me to update to the latest version of VCDS? or do i need to do some reflash the cable?
The link for OBD2cartool DK members VIP offer is Down Why ?? i already ordered 5 peaces and pay for it
Why its Down ?
https://www.obd2cartool.com/vip-link...tubt40p5prjok5
Hello. Does someone have vcds 18.2.0 ROJ?
What you need, firmware for the interface or software?
Hello Everyone,
First I'd like to thank you for your help much; would you please give me a list of tools required to repair and where to get the dump file to program the atmega controller;
what happened to my cable was I thought a cloned cable an original one so, I went to ross tech website and downloaded the latest software ver 20 and ran it without any loader I was naive ; the cable gave status : Not plugged into car despite it was connected to obd connector of a Golf 6 car
the problem seems to me that an original software got the cable disabled/banned. I played with a couple of tools in order to undo what the original software has done; I programmed the FTDI USB interface but I couldn't get to the atmeg controller expecting it has a boot loader to program.
I ordered USBASP programmer from local dealer. But I need a road map; I know about lots of things now the atmeg is used to communicate to car and ftdi is usb controller i know about pinouts of the obd; I know about ftdi FTDI232RL which is my case MY GAL controller is PALCE
I have been searching, studying your forum but, I still confused and i need a roadmap/steps and dump/tools if it does not bother You.
1.jpg2.jpg
Test VCDS USB Interface
Device : 1
Description : Ross-Tech HEX-USB
VID & PID : 0x0403FA24
FT_Chip ID : 0x9025AF2C
SW Version : 131.24
Loader ver. : 0.196, HP
Check Sum 1 : 0x8E01
Check Sum 2 : 0xB5FD
Firmware : unknown
Clone mark : !!!
SN : 0x808080281D818088
Test was completed successfully !
not plugged.jpg
Bookmarks