VAG-COM/VCDS EVERYTHING

[JetSet59]

You need to reflash the FDTI eeprom with good .EPT file

[max4ever]

You need to reflash the FDTI eeprom with good .EPT file

Where did you get that from? Have you version 908.ept?

[mattydr67]

Where did you get that from? Have you version 908.ept?

This is it:
Good luck

[bibkare]

Hi again! I flashed Atmega 162 succesfull but it gaves me the next error:

you don't have can shown so that means while you were programming either you had power connected where is not supposed to be or you damaged board soldering, over heating, or too fast pc, it could be numerous reasons, give us a pics of your hardware etc..

[Dima_minsk]

Did you just use flash 1.83 without corresponding eeprom, if you did it's no good

so give a link to EEprom? or make a PrintScreen of the fact that you are running VCDS 10.6!

[ipejasinovic]

Jejeje. Someone is pissed...

[mattydr67]

so give a link to EEprom? or make a PrintScreen of the fact that you are running VCDS 10.6!

Forget about.
VCDS 10.6 dump aren't for free.
Good luck

[art64]

Were you too excited when you wrote those questions 'cause none of these makes any sense, please rephrase, one by one and i will try to answer it asap

Hello,Bibkare, and thank you for care.It looks good peaple living there.Patient and friendly.Especially thanks to KenshinPT.I suppose, he is not that nice lady looking to us from the avatar
It is not necessary to know exactly,step by step,how did the interface work.I think,I will do nothing with my cable.Maybe in future,if will be 10.6 version for freeIt is risk to do something bad and new clones costs low prices.Original cable costs not a lot.But it is good to learn about structure of interface.Most of automotive devices are build in similar manner(CPU-eeprom-flash),so it's good to learn.
Perhaps it's impossible to built 10.6 version hardware interface on the 805 (812) base without serious changes?

[max4ever]

@bibkare

My hardware: http://img203.imageshack.us/img203/9353/dscn0610j.jpg
and another side:
http://img511.imageshack.us/img511/888/dscn0611r.jpg

[bibkare]

@bibkare

My hardware: http://img203.imageshack.us/img203/9353/dscn0610j.jpg
and another side:
http://img511.imageshack.us/img511/888/dscn0611r.jpg

first side of pcb can't see s.h.it but i think you have stc chip on it, you should take a pic again then i'll be sure is there anything else that should be remove prior to programming

[bibkare]

Hello,Bibkare, and thank you for care.It looks good peaple living there.Patient and friendly.Especially thanks to KenshinPT.I suppose, he is not that nice lady looking to us from the avatar
It is not necessary to know exactly,step by step,how did the interface work.I think,I will do nothing with my cable.Maybe in future,if will be 10.6 version for freeIt is risk to do something bad and new clones costs low prices.Original cable costs not a lot.But it is good to learn about structure of interface.Most of automotive devices are build in similar manner(CPU-eeprom-flash),so it's good to learn.
Perhaps it's impossible to built 10.6 version hardware interface on the 805 (812) base without serious changes?

It's not impossible trust me you just need a little practice and patience

[KenshinPT]

It is risk to do something bad and new clones costs low prices.Original cable costs not a lot.But it is good to learn about structure of interface.

If you want to learn you need to make s*h*i*t sometimes!

I ordered lots of spare parts for it and I already used a few!

[bibkare]

so give a link to EEprom? or make a PrintScreen of the fact that you are running VCDS 10.6!

is this OK

[max4ever]

Evrika! It works, it works!!! URAAAAAAA!!!!

Thanks everybody!!!!!!!

[Some0ne]

Tell me please, where can I find a dump for the atmega chip hex-can-usb