VAG-COM/VCDS EVERYTHING

[teerak2uk]

i cant see atmega is supported in UPA

[ogo777]

dont have original tool vcds

[spychu14]

i cant see atmega is supported in UPA

So use other programmer.
PonyProg Kit
SI Prog schematics

[teerak2uk]

in xprog-m it has Atmega 8,16,32,64,128 can these be used?

[mishu_b]

...
no you need Atmega162.

if you do not have support for it you can use the easy (cheap) way to reprogram the uC - parallel port and PonyProg.

you can find here schematic for parallel port and also PonyProg.

atb

[danys]

...
if your tool is genuine - you can do it just using the latest sw available on producer site.

atb

DEAR mishu_b
what does meen
"tool is geniuine you can do it from producent site"

i try to flash by bootloader whith my project made in BASCOM AVR so j know that's posible.

how to do this in this interface.

[teerak2uk]

...
no you need Atmega162.

if you do not have support for it you can use the easy (cheap) way to reprogram the uC - parallel port and PonyProg.

you can find here schematic for parallel port and also PonyProg.

atb

ok thanks and what is used to program GAL part

[KenshinPT]

ok thanks and what is used to program GAL part

ELM - Simple GAL Programmer

Welcome to GALBlast

[teerak2uk]

Thanks guys for all your help but i think for the cost of a clone ?39 maybe is easier to just buy another

[mishu_b]

DEAR mishu_b
what does meen
"tool is geniuine you can do it from producent site"

i try to flash by bootloader whith my project made in BASCOM AVR so j know that's posible.

how to do this in this interface.

My DEAR,

The MAIN problems with clones is that the serial written into EEPROM of the Atmega162 (uC) will be part of blacklist for the new release of the sw.

this is the reason to use external programmer to reflash the uC.

if your tool is GENUINE~900$ (not CLONE~50$) - your tool will do automatically update without damage when you will use last release of the sw- it means your tool will work without any other work.

-if you developed something for clones - that is fine, I have no time to spend for such thighs, I would prefer the classic way, external programmer.

So if you have developed one tool for updating the fw and serial without external programmer please share with us.

atb

[mishu_b]

Thanks guys for all your help but i think for the cost of a clone ?39 maybe is easier to just buy another

...
so, you do not need to reprogram GAL device, you need to reprogram only the uC.

it is so easy for you - I would say that you will be more happy if you will do by your self than buying a new tool.

just do it!

if you need support - you will have it here, just ask.

atb

[petrodies]

Hi everybody ,

Could someone explain me how I can repair my clone with RL chip ( pics on page 125 ) using an UsbAsp cable.
Worked with 10.6.3 before

Thanks

[marian.m]

I have some problems in upgrading my vcds interface. I programmed the atmega with a parallel programmer and I think that I haven`t set the fuses right.
When the interface is only in USB port there is no problem, but when I supply with 12V on PIN 4 - and PIN 16 +, it says Port status: OK ; Interface not found. The LED first is red, after turns green. It is a BL based interface.
Now the lock bits are not set, the BOOTRST=0 , BOOTSZ=10 , BODLEVEL= 111 , CKSEL= 1101 with SUT=00, CKOUT= 1. Are these allright?

Thank you!

[mattydr67]

marian check this out
Good luck

[mattydr67]

Hi everybody ,

Could someone explain me how I can repair my clone with RL chip ( pics on page 125 ) using an UsbAsp cable.
Worked with 10.6.3 before

Thanks

Here it is the tutorial made by Aminebot.
Just use the VCDS 11.2 dumps shared by KenshinPT
(if always when someone wants to reprogrqamm his tool will ask again and again without reading this thread, this one will become bigger and bigger and in the end it will become unusefull )
Good luck