VAG-COM/VCDS EVERYTHING

[nicu_cuc]

have someone dump to work ok with vcds 11.3
thanks

[liviudiaconu]

maybe not for free, if for 10.6.4 was "alms"...this time i suppose not.

[LittleTOXA]

Collecting your ideas ..

VCDS 11.3, chineese cables with FT232BL chip. Passes test and works just fine. But when I use auto-scan - I get error license message and have to reflash the cable.

License is not blacklisted - this confirms that it passes Test and shows Fully registered each time I do the test. I can work with car for a long time (CAN also). Only in auto-scan there's something which changes the eeprom ..

Who knows what is that ?

[mattydr67]

Collecting your ideas ..

VCDS 11.3, chineese cables with FT232BL chip. Passes test and works just fine. But when I use auto-scan - I get error license message and have to reflash the cable.

License is not blacklisted - this confirms that it passes Test and shows Fully registered each time I do the test. I can work with car for a long time (CAN also). Only in auto-scan there's something which changes the eeprom ..

Who knows what is that ?

What dumps did you use for reflashing?
The 11.2 dumps or with a tool that is bought from China as 11.3.
Good luck

[LittleTOXA]

What dumps did you use for reflashing?
The 11.2 dumps or with a tool that is bought from China as 11.3.
Good luck

That is from China 11.3

[mishu_b]

...
one more VCDS tool found.

FTDI - BL

after re-flash the uC - first test looks good - second one become unregistered!

also - if the tool is plugged first into OBD I get the message USB device unrecognized.

if I plug first into USB device is recognized correctly.

where should I look?

[tiguan]

VAG-COM HEX + CAN


I long ago this old interface from someone
VAG-COM HEX + CAN
I do not know if it original or clone have no software.
How can I update this to work. See these pictures

Data Interface Cable:

HEX + CAN
Dual CAN & K <-> USB
Interface for VAG-COM
HC450557 Rev.A
www_rose-Tech_com

Inside:
FTDI = FT232BM
ATMEGA162


Thanks for your help
tiguan

[cniky]

@tiguan - This is a clone interface 607

[tiguan]

VAG-COM HEX + CAN


I long ago this old interface from someone
VAG-COM HEX + CAN
I do not know if it original or clone have no software.
How can I update this to work. See these pictures

Data Interface Cable:

HEX + CAN
Dual CAN & K <-> USB
Interface for VAG-COM
HC450557 Rev.A
www_rose-Tech_com

Inside:
FTDI = FT232BM
ATMEGA162


Thanks for your help
tiguan

@tiguan - This is a clone interface 607

Ok many thanks
This is also updating clone 607 to work.

[DaniXDX]

Hello!

Vag-com I have a fully functional 11.2 has been deprogrammed.
Take the FTDI232BL, I have the. Ept to program, but leaps Mprog me an error "Error reading device" ... Anyone know the solution?

I think the Atmega is well programmed, only the FTDI, to change the VID & PID work, but I miss that mistake Mprog ... What I can do?

[bibkare]

VAG-COM HEX + CAN


I long ago this old interface from someone
VAG-COM HEX + CAN
I do not know if it original or clone have no software.
How can I update this to work. See these pictures

Data Interface Cable:

HEX + CAN
Dual CAN & K <-> USB
Interface for VAG-COM
HC450557 Rev.A
www_rose-Tech_com

Inside:
FTDI = FT232BM
ATMEGA162


Thanks for your help
tiguan

this is probably the best hardware for clone interface, i couldn't see well in picture are those SI chips instead of transistors and you have connections from atmega to side holes so you don't have to solder on atmega directly, very nice

[deco30]

Vag-com I have a fully functional 11.2 has been deprogrammed.
Take the FTDI232BL, I have the. Ept to program, but leaps Mprog me an error "Error reading device" ... Anyone know the solution?

I'm not sure now, because I did long time ago, but Mprog is supporting only ports with low numbers so maybe you need to change it.

[deco30]

Please also try to use another (or latest) FTDI drivers.

[magadan]

.... Mprog me an error "Error reading device"...

What number VID, PID has a cable? In the Manager of devices.

[DaniXDX]

Deco, I use the last FTDI drivers, and COM 1. The Mprog read the 232BL, but not programm.


Magadan, the VID is 0403 and the PID 6001 (tipical in FTDI Serial Converter).

Thanks!

Sorry for the English.