VAG-COM/VCDS EVERYTHING

[ovi_dk]

Well ,i uninstall all ft driver from mi pc and now whw when plug in the vcds i get this

[mladen76]

Mate,give me your TeamViwer on P.M.if you have,I will try to do it for you.

[ovi_dk]

I dont know wi i have pid0020 and vid 0003,i give uninstal to this but even if i put the cable on the same pc or to anoather the usb recunoise the same the interface like in mi second post!Its a way to uninstall this,or i have to reprogram mi vcds??Thank u!

[mattydr67]

Well ,i uninstall all ft driver from mi pc and now whw when plug in the vcds i get this

Now right clik on that
Then Update drivers
And use manually update browsing to the C:\Ross-Tech\VCDS
And Next and so on
Install drivers
Good luck

[mattydr67]

I dont know wi i have pid0020 and vid 0003,i give uninstal to this but even if i put the cable on the same pc or to anoather the usb recunoise the same the interface like in mi second post!Its a way to uninstall this,or i have to reprogram mi vcds??Thank u!

IF you have diffrent VID?PID the 0403/FA20 try to use the procedures and then use MProg
Maybe you do not need to reflash the Atmega.
This depend of your kind of tool
Good luck

[ovi_dk]

With mprog showme 0 divice found,if i give to pick driver manualy dosen find nothing!Anny advice?
Thank u

[The Strokes]

Hi dear friends
I need lile help ,sugestions
Yestoday get one vcds clone 11.10,after insatll on pc get the error like in picture wath i attash,the cable dont find any drivers and can not install,the cable its new,i try to install on other pc but same problem.
Can somone tellme wats wrong?
Thank u for any sugestion
Regards

Did you get your clone working? if so,where did u get your from?

[mattydr67]

With mprog showme 0 divice found,if i give to pick driver manualy dosen find nothing!Anny advice?
Thank u

Use the procedures writing two lines ( with you VID/PID ) in the RT-USB.inf and after this you'll be able to install drivers as ross-tech
After this you'll be able to use MProg
Good luck

[ovi_dk]

Thank u to all for help,mi ftdi was death,no programabile,so i will change with new one adn hope all come to normal.
Thank u once again

[tk500]

Not so much.

[randomlog]

Use the procedures writing two lines ( with you VID/PID ) in the RT-USB.inf and after this you'll be able to install drivers as ross-tech
After this you'll be able to use MProg
Good luck

You can use this: http://www.digital-kaos.co.uk/forums...8/#post1488361

[tricoredc17]

Yah yah... right... I'll do it for free for anyone interested. Now get the fcuk out.

From the original VCDS also read it?

[KenshinPT]

From the original VCDS also read it?

Yes.

Regards.

[matekhr]

My old vag-com cable makes me a lot of troubles, so I ordered a new one. It arrived yesterday, didn't work (of course) so I opened it.
Instead of Atmega there's a chip marked D79F8513A (China).
What a hell is that?

[mattydr67]

My old vag-com cable makes me a lot of troubles, so I ordered a new one. It arrived yesterday, didn't work (of course) so I opened it.
Instead of Atmega there's a chip marked D79F8513A (China).
What a hell is that?

That is NEC not ATMEGA
You have bad luck in this case becasue for this kind of tools there's no solution, I mean no dump for NEC
Try to reflash it with MProg maybe you have a littel luck and it will work but in other case you have to buy another tool.
Good luck