VAG-COM/VCDS EVERYTHING

**pomarada** · 8th October, 2012, 03:45 PM

I am putting 5v

**mattydr67** · 8th October, 2012, 03:51 PM

[quote=ahadi;1724203]

Originally Posted by mattydr67

99.99 of Chinese sellers are cheaters.
You was cheat by them

this is not correct, work with original is more easy than clone . 99.99 want save money buying clones ,90 of them dnt know the difference .

20 of DKs are leachers .

I don't know what you want to say but when a seller told you that he/she sell you a vCDS 11.10 for sure he/she is lying you.
Anyway I don't say that you cannot works with a clone but more peaple are cheated by Chinese becasue they don't know what to buy or they haven't information.
What I want to say that in China the last clones it is VCDS 11.11.0
Well it is one which works with a chinese softwear ( cracked one ) fo VCDS 11.11.3 but this one have a lot of bugs. Bad cracked i suppose.
But this is not my problem.
Anybody can what they want to do.
So this is my opinion and if you're agree with me it is Ok if you aren't it is OK too
Good luck

**pomarada** · 8th October, 2012, 03:59 PM

I just put votios d12 and now LED lights.
Checking votaje 11.26v will arrive at 7805.
The funny thing is that the transformer sends 12.32v offline.

The extreme still gives me the error

**mattydr67** · 8th October, 2012, 07:56 PM

Originally Posted by pomarada

I just put votios d12 and now LED lights.
Checking votaje 11.26v will arrive at 7805.
The funny thing is that the transformer sends 12.32v offline.

The extreme still gives me the error

Did you solder together the GND of Programmer with the Power GND?
Good luck

**pomarada** · 8th October, 2012, 09:24 PM

Originally Posted by mattydr67

Did you solder together the GND of Programmer with the Power GND?
Good luck

Hello
Attempt to of two ways.
- The output 5v programmer, pin 2 positive, and pin4 mass.
- Also with 5v source, independent power
With 5v, do not LED lights up, the vag

Then change to 12 volts independent. With 12 volts if you light

Is there any problem if 13voltios?

Greetings and thanks for the help

**liviudiaconu** · 9th October, 2012, 06:49 AM

connect the 4 wires between programmer and atmega, the GND of programmer to GND of VCDS, power on +12 V VCDS, plug-in usb cable. Open eXtreme Burner, open file[s], set and check good fusebits, write...
If not, check the +5v after 7805. If is OK, you make a mistake, or your programmer is not OK..or..atmega locked/damaged.

**stormb** · 9th October, 2012, 09:32 AM

Firmware 1.92

**tricoredc17** · 9th October, 2012, 02:20 PM

It is possible to program the NEC?

**MiStch** · 9th October, 2012, 07:36 PM

Hi there
I'm new here and as Ross-Tech seems to take copy cables more seriously, it killed my VCDS cable. I hope I get mine working again with these tutorials.
Otherwise, I'll bother you...

Thanks for helping.

**mattydr67** · 9th October, 2012, 08:25 PM

Originally Posted by tricoredc17

It is possible to program the NEC?

It is possible but no dump for NEC
For the the solution if your tool is erased it is to buy other one, maybe with Atmega this time.Sorry you have no choice.
Good luck