VAG-COM/VCDS EVERYTHING

**mattock808** · 24th July, 2019, 07:35 AM

Originally Posted by fantomel

A little history lesson maybe some of you need it

EN - DE - FR - IT - ES - PT - PL - HU - RO - NL - RU - SWE - CZ

CZ link doesn't work. Can you repair/reupload pls?

**Mario6** · 24th July, 2019, 08:03 AM

mattock808

Here you have.
CZ
EN
PL

https://zachowajto.pl/hledej?q=vcds+...tocomplete=std

**bg17aw** · 24th July, 2019, 08:23 AM

Any ideea how this situation is possible? VCDS doesn't detect the interface, but HWType does:

**mattock808** · 24th July, 2019, 08:35 AM

18.9.0 CZ is latest ?

**pinkmercedes** · 24th July, 2019, 03:45 PM

Hi.
I'm trying to fix my old chinese cable with Atmega chip.
I've flashed it using programmator and VAGCOM_EEWriteLang.
Everything seems ok, cable passes test, connects to car (Golf 7 2013).
But when I try to write a new value (for ex. Adaptation...DimmwertAB 25) i get error:
"This interface does not support sending CAN messages 256 bytes and over in length"
I've tried different VCDS version from 17.1 (it was on disc with the cable) to 19.6.0, different Loaders versions from 5 to 8, different firmwares...
But no luck, I'm still getting this error.
The cable worked well a few years ago with the same car. I was able to write values (for ex. in Adaptation...DimmwertAB 25).
Can't get what I'm doing wrong.
What else to try?
Thank you.

IMG_6508.jpg
IMG_6512.jpg
IMG_6514.jpg
Update:
Just figured out what was wrong. I tried to edit the wrong channel. "...Light configuration..." instead of "...Leuchte25KZL HA59...".
Ughhh...

**hid3** · 24th July, 2019, 04:04 PM

First of all, remove those two jumpers.
Secondly, you have flashed it as HW 0x44, right?

**pinkmercedes** · 24th July, 2019, 04:49 PM

Originally Posted by hid3

First of all, remove those two jumpers.
Secondly, you have flashed it as HW 0x44, right?

Hi.
I've done all this (flashing and connecting to car) with those two jumpers and without them.
Also I've tried flashing both firmwares 0x44 and 0x46. Cause I'm no sure which revision it is. Pin 35 is connected to GAL, but pin 34 is not.
It works the same way. VCDS test says OK. I can read values from car but cannot modify.

**ZIPPO4594** · 24th July, 2019, 06:46 PM

Licence is activated on VCDS ?

**sahraoui1** · 24th July, 2019, 09:47 PM

hi please need dump for 2 models of vcds 0x44 and 0x46
thnks a lot

**bg17aw** · 24th July, 2019, 11:27 PM

Originally Posted by BASi77

A few words about the C-Test.exe. If the test message appears:

Attachment 627724 Attachment 627731

This means that the device is marked as "clone". After deleting the mark:

Attachment 627725 Attachment 627729

Could anyone upload the latest c-test.exe? When I run mine, it always fails ("Program not responding")

**pinkmercedes** · 25th July, 2019, 09:35 AM

Originally Posted by ZIPPO4594

Licence is activated on VCDS ?

Yep. License activated.

**Nicolar** · 25th July, 2019, 09:49 AM

Hi everyone. I have a HEX-V2 clone cable. With version 18.9 it works. I installed version 19.6 of kolimer but it doesn't work. The Failed 4 message always comes out. What can I do? Thank you

**alexm1** · 25th July, 2019, 09:59 AM

You should do, what everybody does...wait for a new fix and until that, use 18.9.0.

**Nicolar** · 25th July, 2019, 10:22 AM

The problem is that the program does not work. When I open it from the loader.exe it gives me Failed 4. Without that I connect the cable to the computer. Then the loader.exe does not work? Thank you