VAG-COM/VCDS EVERYTHING

[aminebot]

Counting from the GAL16V8(right side):
red-green-white-black

In some interfaces , wire are inverted , verify using a multimiter if red wire is 5V and black wire is gnd with usb cable connected to PC.

[bibkare]

Did you tried to reprogramm it again?
Good luck

yea i reprogrammed it with 3 different dumps and every time could work only with 704, but it's OK, i just wanted to show this kind of hardware and to ask others did they have any experience with it

[bibkare]

see this interface, it's almost the same

[ipejasinovic]

704 version didn't have check for R family of FTDI chips, so that is why it's working. When 805 came out, devices was supplied now with R chips. R chips have unique sn, which can't be changed, so, Uwe figure out to make sn from Atmega to depend on sn from FTDI. So, you have some tree created: Devices with FT232B and devices with FT232R.

[Steve L1]

I have a newer audi a3 2007 2.0 tdi i had the old odb 11 cable ,it wont recognise my car with the vcdslite i havd from here .will i need the hex can cable .and what version of vcds do i now need
cheers for any help

[bibkare]

I have a newer audi a3 2007 2.0 tdi i had the old odb 11 cable ,it wont recognise my car with the vcdslite i havd from here .will i need the hex can cable .and what version of vcds do i now need
cheers for any help

You need at least VCDS version 805 and hex can interface

[Steve L1]

You need at least VCDS version 805 and hex can interface

Is that version available here ?

[Steve L1]

i do not have permission to view the threads .whats this all about then ? i have been on here ages ....

[PEDRO4053]

Testing with a multimetro connected cable in the black pc +5v - white earth - red earth pulsed and green earth pulsed.

The white thread didn't loosen of the plate ,a connection it would be like this:

Black
red
green
white

Thank you
Pedro

[slevesque]

So you couldn't install the driver?
I suppose so.
Install it manually
The folder of driver it is the same one where is the VCDS installed.
C:\Ross-Tech\VCDS
Good luck

Yes but I received the same message when I tried to install manually. I really not understand the problem

[aminebot]

Yes but I received the same message when I tried to install manually. I really not understand the problem

Execute DPInst.exe in the attached archive. it contain 64x drivers.

ROSSTECH_Drivers_64X.rar

[ironderek]

Hi, I have 10.6 interface which never worked- when I've got it said error -1 and software didn't won't to start. Interface has FTDI232BL inside, and doesn't have STC chip. I reprogrammed it with 805dump and everything works fine, but if I unplug it from computer and plug again, interface is no more recognized as Ross Tech. Then I have to program it again with .ept file, and again works only for one time until is plugged into computer and car, after when i unplugged it again to same problem. What is wrong?

[bibkare]

Hi, I have 10.6 interface which never worked- when I've got it said error -1 and software didn't won't to start. Interface has FTDI232BL inside, and doesn't have STC chip. I reprogrammed it with 805dump and everything works fine, but if I unplug it from computer and plug again, interface is no more recognized as Ross Tech. Then I have to program it again with .ept file, and again works only for one time until is plugged into computer and car, after when i unplugged it again to same problem. What is wrong?

Obviously your dump isn't good. Try to reflash it with 908 dump

[Nio]

Nice work guys. Thanks.

[mattydr67]

Hi, I have 10.6 interface which never worked- when I've got it said error -1 and software didn't won't to start. Interface has FTDI232BL inside, and doesn't have STC chip. I reprogrammed it with 805dump and everything works fine, but if I unplug it from computer and plug again, interface is no more recognized as Ross Tech. Then I have to program it again with .ept file, and again works only for one time until is plugged into computer and car, after when i unplugged it again to same problem. What is wrong?

When you have that eror and the softwear dosen't start, that is a chinese cracked softwear and you need for it a VCDS with Ft232RL inside.
That sw it is made for that kind of interface.
If you have a FT232BL inside reprogramm it with dumps ( you can find it in this thread ) and you'll use an original ross-tech softwear not that one that your interface came with it.
Good luck