hallo, can I have the Link from HEX V2? Thanks
hallo, can I have the Link from HEX V2? Thanks
Maybe here
https://www.obd2cartool.com/diy-vag-...hipping-p-1388
i am waiting for an special offer to dk-member.
Col19 (5th January, 2020)
Already is blocked.
19.6.2 ZHS and ZHT just released.
https://www.digital-kaos.co.uk/forum...=1#post3743045
Before opening the hood, the adaptation button was grey in your vcds? We have a new Skoda Octavia, and the adaptation button is grey in the 09 cent. Elect, (after i wrote the security acces code)
Last edited by Zippair; 19th December, 2019 at 04:08 AM.
Does anyone have the "HEX-V2" interface which is faulty due to "CAN not ready" issue? Please PM me.
I can calculate ABS module codings for:
* Continental/Teves MK60EC1 and MK60;
* TRW systems in Passat B6 / B7 / CC /Tiguan;
* MK100;
* Bosch ABS8.2, ABS9.0 and ESP8.2, ESP9.0;
* EBC 460 (UP!, Mii, Rapid, CitiGo, Fabia, Toledo, etc) New!
* ... and other VW/Audi/Seat/Skoda modules.I can assist with repairing \/CDS interfaces.
Hi. Can anyone share vcds 18.9 ENG?
You can try!
Best regards VCDS.doc
Col19 (20th December, 2019)
No nothing was grey. Still I could adapt or code but the application will be refused at the final step.
Besides, it seems that with 19.6 the adaptation of central elec was grey even after entering the correct access code . I'm not sure (poor memory) but that might be the reason why I always use 18.9.
Hello! I have 19.6.2 if i want to connect to some modules, like 61.Batter regul., I've received "No response from controller" ...Is it the problem because is not a genuine version? Thank you
No. The reason is not whether the cable is "genuine" or not. It will always take some time for the software to be updated to support new modules of a new model car, so it's comon that some new modules are not supported by current software.
At the same time, the manufacturer started intentionally limit the compatibility of old cables to promote HEX-V2, so sometimes, old versin software supports a module but new version does not.
just try another version.
Last edited by Maitreya; 21st December, 2019 at 09:40 AM.
I am trying to update a friend's old cable (11.11), please see pics:
1) is this HW44 or HW46? I think it is HW46
2) VAGCOM_HWType.exe says interface not found, every time, although the interface works on the car. Any idea why?
3) Device Manager says "Rosstech Direct Interface" and VID:0403 and PID:FA30 but some tutorials say I should change FA to 20, how do I do that? They mention a software called "vidpidfix.exe", where can I find this?
4) JP1 is briged (a connection exists soldered on the board), should I desolder it?
5) The board already has the holes for programming interface, so am using those, is it alright if I connect the cable to a 12V supply and only use 4 wires from USBASP programmer to the board? So no VCC and no GND?
6) No ATF/GAL?
7) No L7805??
Thanks
Last edited by bg17aw; 22nd December, 2019 at 01:06 PM.
Your cable is a petard without GAL/ATF, without 7805.
For work FA24, K0l1m3r solution. Or, external programmer with "46" settings. Until you don't rewrite FA24 is possible K0l1m3r solution not work.
bg17aw (23rd December, 2019)
Bookmarks