VAG-COM/VCDS EVERYTHING

[nextor]

That sounds easy. Do you have a link to such a GW?
Do I need an additional ECU connected to the GW or can the VCDS cable/SW talk to the GW directly?
I have an old Audi A3 ECU from 2005 that I was suppose to use on a different project but perhaps I can connect it to this GW?

It really is easy, I'm sending you a PM with a link to a YouTube video I just made showing the setup.

I used this setup to connect to different engine ECUs using K-Line or CAN, so for sure you can connect to that Audi A3 ECU

[ZIPPO4594]

That sounds easy. Do you have a link to such a GW?
Do I need an additional ECU connected to the GW or can the VCDS cable/SW talk to the GW directly?
I have an old Audi A3 ECU from 2005 that I was suppose to use on a different project but perhaps I can connect it to this GW?

you can connect VCDS cable directly on GW.
My test box has A3 8P GW. On it, i check hex-can and Hex-V2 interface

[mepsnet]

I want to ask if anyone know can VCDS HEX V2 ARM model work with internet, I used it without loader and after some time program was locked had to reinstall. If I run it every time with loader and with internet then it wont block program, right?

[MichaelKors]

Reinstall it, block VCDS access to internet in the Windows Firewall and add the IP line in Hosts file.
After that you will be able to use it without loader, with internet, and you will not get License Revoked.

[sep382]

I greet people
question, help
I have HEX-V2 dual-k & can H11-025771, I have VCDS 21.3.0 software, it happens that when I connect the interface to the vehicle, atmel 162 is deleted, I revive it on the table, put flash and eeprom made with tl866 + and on the table does everything as soon as I reconnect to the node the same thing reads the instrument or abs or airbags and stops ejecting the interface not found firmware: !!! cloned label: !!!
if I do something wrong or the software is not compatible with the interface
help please
thank you
P.S. advice or solution

[bendzji]

Post photos of PCB , there where some hardware version that you should cut some connetion on PCB. Everything od written in Loader folder

[sep382]

41 / 5.000






Rezultati prijevoda

41 / 5.000






Rezultati prijevoda

I am attaching pictures of my hex-v2 dual-k & can

[electronistul21]

ist not trouble with license.is broken cable,need adjust hardware part

[sep382]

hello electronistul21
can you help me solve that
I enclose the flesh + eeprom that I use to revive hex v2

P.S.
the license is ok when i do the flash again
thank you

[jan4]

try with version 20.x and keep flash and eeprom from same version 9.2

[sep382]

greeting
version 20.4.0 20.4.1 20.4.2 England
same problem
vehicle connection test ok, interface found, contact, select engine and eject interface not found

[bendzji]

did you try to flash FTDI with files from VCDS Loader Folder ? Flashing using vagcom_eewrite.exe works?

[mepsnet]

Hello I have vcds arm stm32f405, after some time it dont work, no lights, no sound when connect to PC. I opened it and dont see anything burned, is there any method to get it in life again?

[wiechec]

Hello I have vcds arm stm32f405, after some time it dont work, no lights, no sound when connect to PC. I opened it and dont see anything burned, is there any method to get it in life again?

Post your VCDS PCB photo.

[jach0o]

I got hex-v2 (not real - old but it can be updated) i what ot buy real not genuine hex2 where to buy can you link me with good motherboard? Will it work like genuine Rosscom hex2?