hi
not by type of car!!
The most important information that you have 27c512 or 28c512 inside
because there is a difference if the 27c then to 23 pin mcu
, if it is 28C to 22 pin MCU
immo pin 30
regards
Hello guys!
I just lose my temper today !
I CUT also line 30
I try to IMMO off on SAFIR 2. I try with 23 pin to GROUND NOT WORKING ... Car won't start!
I try Immo DECODER .... Same shit don't work ... Car won't start.
If i mess WITH KEY car start .... like it was not virgin.
So is it possible i need EMULATOR ?
Don't know what to do any more
Please HELP
Last edited by fruti; 6th September, 2013 at 12:19 PM.
hi
not by type of car!!
The most important information that you have 27c512 or 28c512 inside
because there is a difference if the 27c then to 23 pin mcu
, if it is 28C to 22 pin MCU
immo pin 30
regards
Please dear members push the button thanks and reputation button(stars)
do you need help? fill it in !!!
Model:
Motor capacity:
Diesel/Gasoline:
Production year:
ECU type and number:
Memories :
https://www.digital-kaos.co.uk/forum...63#post1660863
Bro ... it is 27c512 But don't work ....
I just reading this and i see i need to put Safir2 to ADVANCED 1 or 2 mode ... i use Standard.
If i working via 23 pin to mass .... nothing happen. I know that it must CLICK CLICK and restart fuel pump but when i do that it nothing happen. No restarting no noise.
That why i use this Immo decoder ... i will leave that for 4 hours and lets see what will happen
Decoding process is fully automated. On SIEMENS FENIX5 select Standard type of operation (green LED off). Other systems may require
Advanced1 or Advanced2 mode (especially engine control systems, where
ignition-on signal to ECU is passed via fuel pump relay coil, e.g. SAFIR2).
Decoding in Standard mode takes about 1h 50min, in Advanced 1 ***8211; 4h, in
Advanced 2 ***8211; more than 5h. In most cases 1h 50min is enough to make
ECU not coded. Ignition is switched from off to on by decoding tool; red
LED indicates ignition on. After decoding, ignition is switched off and
green led is lit permanently.
Ok ... Advanced 1 mode .... now 4 hours waiting
Sagem SAFIR 2 IMMO off - YouTube
Hello, look this tutorial password in mp,
simply put on the photo I touch the red pine with a small screwdriver up and down.
connected computer on the car ignition is.
A +
airfree (28th September, 2018), amrif (17th October, 2019), anour10 (3rd January, 2019), Disconnected (18th April, 2016), egycyclops3 (11th May, 2018), Le-Mans (23rd July, 2018), r0my81 (10th August, 2015), Sady369 (30th June, 2021)
Hi, i have the same problem here . The car is far away and i need a working solution.
SAfir 2 with 55 pins
Chip: 27c512
I did the Renault - Tool - advanced for 4 hours
After i checked : light goes on and after 2 seconds goes off like before
I tried the tiny sweeper and connect the signal cable to pin 23 (and also tried pin 22) - pin 23 is ground directly (my opinion is this pin should
be lifted up to make the tiny sweeper working.
After several runs with the sweeper i conected the Renault Tool again - light is like before , goes on and after 2 seconds goes off
Does anyone know how i can be shure that the immo is off ?
THanks
WATCH MY TUTORIAL
I made ***8203;***8203;off real calculator on the car, touch it,
One guy running the starter
I pine key simultaneously.
tested 100%
joe1953 (2nd March, 2014)
Thanks Dell, but the car is about 800km away, will check your solution:-)
Connect for Renault Tool
SAGEM SAFIR (55 pin)
Connect only three wires to decoder box: ground, immobilizer line and
switched +12V. Connect decoder***8217;s red wire to constant +12V. Information
about Ignition-ON is supplied to SAFIR via relay coil. Use any relay
(automotive or not) with 12V coil. Select Advanced1 decoding type.
2 -> Ground
18 -> Ground
1 -> +12V After Ignition (15)
through relay coil to pin 48 !!!!!-> +12V After Ignition (15)
TWINGO-43, CLIO-47 ->Fault lamp
37 ->Immobilizer line
after cut 37 pin
r_parev (27th September, 2015)
Hi Ivan, i tried this with this pinout.
I`m using the Renault Tool for the Fenix 5 and it works perfect but this one is other story-
it does excactly the same after completing advanced 1 and standart mode - light goes on and after 2 seconds goes off like before.
Im not sure if immo is off or not ...
POWER SUPPLY more 12.5
use only advanced 1
cut immo line
star the car
Sagen Safir 2-55 pin
A tried and tested solution:
- Ground 2. 18.
- Positive 1.
- Feeding the UCE to 12V
- Put the Pin 22 to ground for 5 sec. and repeat 5 times.
- Cut pin 37.
- Off Realty.
martinracing (11th May, 2020)
Hi!!
I need help with solution immo off.
Ecu is Bosh 0 281 001 956, 2002year tdi
MSB101150
Inside 24c04
ROVER 400 2.0 TURBO DIESEL
HELP ME!
rover 2.0 24c04.rar
Hi please I need pass to open this file
Bookmarks