For Enigma users

[Rito]

Today I try change Renault ScenicIII.....But enigma can?t do it.

Enigma can?t read 24C16, always show frist 3 pins red...
I try read in epron 24C16 in editor but same this 3 pins red...and not for bad conection I test whit other epron and it?s ok..

Dealer says epron have fund in dash is 24Lc16 but I have sure I fund 24C16.
Someone have same problem???

Thanks

[raf0468]

remove eeprom press read {3 pins red } continue anyway see if it gives correct miles if yes save file and carry on programming......

can't remember exactly which eeproms but some eeproms show bad connection enigma does not need them connection to read and write.......

[Digamax]

remove eeprom press read {3 pins red } continue anyway see if it gives correct miles if yes save file and carry on programming......

can't remember exactly which eeproms but some eeproms show bad connection enigma does not need them connection to read and write.......
Yes that is normal for eeprom 24c16 (3 pin red). Continue anyway.

Best regards
Vladimir

[Rito]

If I try continue to read this not read correct value....
So you can do some car like this??


Maybe have other versions dash or machine not work whit this car....

[einet]

24LC16 in some cases is Roteted.
I have the same problem on a Clarion Radio that have this eeprom roteted.

[tachonow]

24LC16 in some cases is Roteted.
I have the same problem on a Clarion Radio that have this eeprom roteted.
If you say so please post datasheet with this chip rotated pins.

[T72]

If you say so please post datasheet with this chip rotated pins.
megane3/scenic3/laguna3 do not have any rotated 12c eeproms..

its simple clip problems...

[dashradio]

24LC16 in some cases is Roteted.
I have the same problem on a Clarion Radio that have this eeprom roteted.

I have never seen a Clarion radio with a 24c16 in it ? only 93c46 rotated pins.?

[digidash]

Enigma certainly can do this vehicle as I have done them myself. They work fine with the chip onboard. If you do take the chip off I think you will find that pins 1, 2 and 3 are all linked on the pcb.

[Digamax]

If I try continue to read this not read correct value....
So you can do some car like this??


Maybe have other versions dash or machine not work whit this car....
Which voltage you use for reading? 4.5V is very good voltage for reading. I always desoldering eeprom from board.

Best regards
Vladimir

[einet]

Sorry! I answer to quickly .
Correct that whose 93C46 rotated. and this whose a
old Clarion Radio for Peugeot.

[nckryder]

24c16 using enigma always 3 pins shown as no connection ( "red" ) just read past it and you should be ok as I never have an issue this way. The same goes for programming 24c16

[Rito]

Which voltage you use for reading? 4.5V is very good voltage for reading. I always desoldering eeprom from board.

Best regards
Vladimir


I use 3.5..
I try read chip outsid pcb but not correct value and show 3 pins red..
Maybe Enigma not know this version??

[dashradio]

Hi, try this if reading 24c16 out of circuit, join pins 1,2,3 & 4 together.

[digidash]

Rito the enigma will definately read this onboard. Read the eeprom and take a look at the data. You should also be aware that you will also have to fit a filter in the dash as it will write back the mileage from the ABS module. So if you dont have a filter ready to do the job you are wasting your time trying.

[Rito]

Rito the enigma will definately read this onboard. Read the eeprom and take a look at the data. You should also be aware that you will also have to fit a filter in the dash as it will write back the mileage from the ABS module. So if you dont have a filter ready to do the job you are wasting your time trying.

I try read But show big value..
Maybe exist more versions and enigma only know one....

Or I don?t know why read big value.......

[digidash]

Post the dump you have I will take a look at it. But did you understand you will need to put a filter to stop the ABS controller writing the old mileage back. Or do you a machine to do this.

[Rito]

I give car costumer..
Maybe my dump not good reader..........
Very soon I will try again in new car..........

Thanks to all...