Edc16c3 with xprog m

[AMON]

Hi, i need help connecting xprog with edc16c3 with x prog.

thanks

[choro]

Hi, i need help connecting xprog with edc16c3 with x prog.

thanks
I make this!!!!!!!!!!!!!!!

[engrami]

hi
how can i get connection diagram of all ecu s

[choro]

I work only with this

[pirilla]

One question:

How do you apply 12V, from external supply or from X-Prog ???

Thank you in advance.

[choro]

I find them every time with multimeter front of the jack

[pirilla]

Sorry, I did not explain well.
My question is if you use an external supply to apply 12V or if you use 12V output from X-Prog.
I suppose you use external supply and you connect 12V and GND in ECU-PLUG. Don't you?

[choro]

Sorry, I did not explain well.
My question is if you use an external supply to apply 12V or if you use 12V output from X-Prog.
I suppose you use external supply and you connect 12V and GND in ECU-PLUG. Don't you?
Yes use external supply and connect 12V and GND in ECU-PLUG.

[AMON]

I have used external supply and manage to read it.

[pirilla]

Someone with PLUG PINOUT ???

[AMON]

just connect +12v to pin 2 and 9, gnd to pin 6, and you will read it

[AMON]

don?t need to use ecu plug pins

[pirilla]

I understand. But I would like to read through K-line too (if possible on the table). I want to know with is better for this.

[AMON]

found this one but could not connect

[pirilla]

This is for EDC16C34, FAP engine version, not same as EDC16C3.

[pirilla]

I make this!!!!!!!!!!!!!!!

I tried with your scheme.
I can read everything OK, but only can write EPROM. In flash software freezes and in MPC, verify detect errors.

Some advice?

[choro]

I tried with your scheme.
I can read everything OK, but only can write EPROM. In flash software freezes and in MPC, verify detect errors.

Some advice?
are you erase flash before you write?

[pirilla]

No, I didn't.
Is it necessary? Only in FLASH or in MPC too?

Thanks

[choro]

No, I didn't.
Is it necessary? Only in FLASH or in MPC too?

Thanks
is very important to erase the flash before write !!!
MPC I think that happens without erase, but not sure

[choro]

Need you help ,

On the supplied photos of immobilizer boxes there are indicated the color wires goes to different connecting locations on each panel.

My question/request is to give me please a drawing about the other end of these wires, which goes to the X-Prog M box through the adapters.
I mean, I would need the wiring diagram for the (TMS) programming adapter; which color wire goes to which pin on the adapter (please see attachment).

Thanks in advanced !
I think that it is not with this adapter, you need this:HC(S)12 BDM adapter

[pirilla]

Does anyone know with pin of ECU CONNECTOR is K-Line (and GND and VCC+IGNITION) ???

For EDC16C3, of course.

Thanks in advance

[choro]

Does anyone know with pin of ECU CONNECTOR is K-Line (and GND and VCC+IGNITION) ???

For EDC16C3, of course.

Thanks in advance
look this foto

[pirilla]

Thank you, but this is for EDC16C34.

Is it same PINOUT as EDC16C3 ???

[AMON]

take a look at this

[pirilla]

This is exaclty what I need.
Thank you very much!

[eduardo74]

Anyone have this PDF in english?

[pirilla]

is very important to erase the flash before write !!!
MPC I think that happens without erase, but not sure

For Your Information: MPC needs to be erased before writing.

[zebbon]

with xprog m
Renault Trafic 2.0 DCI 2007 EDC16c3
MPC562MZP56
M58BW0160B70TF eeprom 95320

[choro]

with xprog m
Renault Trafic 2.0 DCI 2007 EDC16c3
MPC562MZP56
M58BW0160B70TF eeprom 95320
???? ???? ????

[zebbon]

???? ???? ????

Connection to xprog m.....100 percent working!!!

[antibisic]

which option you select?can you read with x-prog full dump(mpc,ex flash,eprom)or you have to read one by one?
Thanks

[miha99]

With xprog-m you read one by one, depend on how you select in devices...

[choro]

Connection to xprog m.....100 percent working!!!
Yes working 100 %

[micromax]

work 100%. now i buy this adapter:
Adapter MPC5xx do programatora xprog-m :: Sklep@AutoDiag.pl (http://autodiag.pl/index.php?p271,adapter-mpc5xx-do-programatora-xprog-m)

work fine, and wait for next adapter :
Adapter HC(9)08 do programatora xprog-m :: Sklep@AutoDiag.pl (http://autodiag.pl/index.php?p299,adapter-hc-9-08-do-programatora-xprog-m)

[stevan]

of course remember that xprog not calculate checksum,must do it with winols or similar soft.

[grinovsky]

with xprog m
Renault Trafic 2.0 DCI 2007 EDC16c3
MPC562MZP56
M58BW0160B70TF eeprom 95320
I think that xprogm can't read MPC562
the connections are right but if you see picture attached you will see too that XPROGM don't read MPC562
i read MPC555 without probleme with xprogm but can't write

[vwphun]

MPC561-2 don't have any internal flash eprom. You can read external flash eprom and eeprom.

[P2XA]

After reflash ecu edc16c3 with x-prog : no communication with ECU...:stoned::stupid: