VAG-COM/VCDS LATEST DUMPS

[betonel]

Please use this thread only for posting working vcds dumps.

Attached 908 working atmega & ftdi dump.


Use thanks if it was useful :dito:

[betonel]

Working dumps for 11.2. FTDI 232BM :captain:

[betonel]

FTDI 232RL ept file. I use UPA usb, first write flash, then eprom to atmega162. Last step check lock bits and fuse bits.
Write FTDI 232RL with mprog 3.5.

[betonel]

More files..

[betonel]

Tested on chinese cable 912.

[betonel]

This interface with FTDI 232RL chip I have tested.
USB VID=0403
USB PID=FA24
Atmega + FTDI program that's all for this hardware.


:giveup:

[kelekele]

What about this hardware vcds 10.6.Is it possible repair this interface:

[uncle_sem]

possible, but not really recommended - ft232RL, transistors/comparators instead of L9637 or another driver for k-line... it's a cheap and bad adapter. usually it's not worth the effort.

[mechanior]

great post betonel

[bursuc]

Hy to all.... i got one VCDS 9.08 , the problem i have :

The LED's are not working at all...i reflash the processor and eeprom but still no leds come's up.
I found one transistor shorted, i take it out .
It was the transistor from K-line... i pun another one from L-line...but still nothing...somebody a sollultion ?
Thanx

[ph0en1x]

Hy to all.... i got one VCDS 9.08 , the problem i have :

The LED's are not working at all...i reflash the processor and eeprom but still no leds come's up.
I found one transistor shorted, i take it out .
It was the transistor from K-line... i pun another one from L-line...but still nothing...somebody a sollultion ?
Thanx

Led is not working if your 7085 regulator not working (check +5V) or atmel is empty.

[bursuc]

i got 5 v , right now i am connecting upa to see if atmel is empty or not . i think in the past i read only eeprom from atmel and seems to be ok , i will read full flash now to check it . thank you

[matekhr]

i got 5 v , right now i am connecting upa to see if atmel is empty or not . i think in the past i read only eeprom from atmel and seems to be ok , i will read full flash now to check it . thank you

UPA won't help you testing is Atmel empty or not, because it is locked. Take dumps from this thread and re-program your Atmel as decribed here.

[bursuc]

still no LED's , i write the dumps, thee eeprom snd the flash on atmega, but still the LEDS are not powering up ... 7805 is working....any other ideas?

[paro44]

....any other ideas?

Maybe led defective or wrong soldered? Power and/or ground on obd connector?

[kelekele]

still no LED's , i write the dumps, thee eeprom snd the flash on atmega, but still the LEDS are not powering up ... 7805 is working....any other ideas?
How you connect upa to atmega 162?I have upa but i'm not sure is flashed properly or not.

[mattydr67]

still no LED's , i write the dumps, thee eeprom snd the flash on atmega, but still the LEDS are not powering up ... 7805 is working....any other ideas?

Hi mate
As other guys told you your Atmega it is blocked
You need to unblock it with a High Voltage Paralel Programmer or how it is named "Atmega Doctor"
Or if your tool was burned by an K-line 12V short maybe the Atemga it is burned.
But I supposed that it is just blocked.
Good luck

[matekhr]

Hi mate
As other guys told you your Atmega it is blocked
You need to unblock it with a High Voltage Paralel Programmer or how it is named "Atmega Doctor"
Or if your tool was burned by an K-line 12V short maybe the Atemga it is burned.
But I supposed that it is just blocked.
Good luck

Yes, right. Check SPIEN fuse bit. Must be "False" for UPA. If it is "True", only a High Voltage Programmer can help you (or a new Atmega).

[doaa]

:bounce:THANKS FOR YOU WORKING GOOD

[modfreakz]

Thank you very very much, my cable working again!!

[cbienmoi2005]

hello,

is possible to repair cable 11.11 to 11.11.3 ?

[mattydr67]

hello,

is possible to repair cable 11.11 to 11.11.3 ?
If you wanna think that if you flash the VCDS with 11.11.0 dump, this will not work with 11.11.3
For the VCDS 11.11.3 you need a moded softwear or 11.11.3 dump
Good luck

[marinescuv]

serial for 11.11.3?

[mattydr67]

serial for 11.11.3?

Yes you need 11.11.3 dump
As my friend Aminebot said in the past the dump you need to be extracted from an old interace with BM because if you have a dump extracted from a new VCDS tool you'll not be able to use it if you do not moded the softwear because it you'll ask for the FTDI RQ ID.
Think about this and you now this dump can be for free maybe after an year at least or never
Good luck

[pacorabane230]

hi , i'm new to this , but does the china blue cable work also on VCDS ?

[mattydr67]

hi , i'm new to this , but does the china blue cable work also on VCDS ?

If you talking abot Vag 409 KKL blue one the answear it cannot work with new VCDS softwears.
Just with VCDS Lite which is made for KKL tools
Good luck

[care33]

tnx for 908

[Africa]

my interface stopped working, the computer does not recognize it interface.

Read EEPROM successful Device 0
0000 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0010 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0020 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0030 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0040 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0050 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0060 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0070 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU

What could be the reason? ...
E2prom enough to program?


I need to program the 93C56.
Any help?

thanks. :beer:

[Artilect]

No need to take the eeprom out. Just reflash with M-Prog3.0 or FT Prog.

If the device is not recognized there is on DK Popsted some tools to repair VID PID of FTDI chip.

If you will not solve. Contact me on PM tonight, im not at home at the moment.

BR

[Africa]

No need to take the eeprom out. Just reflash with M-Prog3.0 or FT Prog.

If the device is not recognized there is on DK Popsted some tools to repair VID PID of FTDI chip.

If you will not solve. Contact me on PM tonight, im not at home at the moment.

BR

I read with mprog3.5 but rarely observed reading.
for that reason Unsolder the eprom and read with upa.

I need internal e2p for repair the interface.

[KenshinPT]

my interface stopped working, the computer does not recognize it interface.

Read EEPROM successful Device 0
0000 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0010 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0020 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0030 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0040 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0050 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0060 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU
0070 : 55 46 55 46 55 46 55 46 55 46 55 46 55 46 55 46 FU FU FU FU FU FU FU FU

What could be the reason? ...
E2prom enough to program?


I need to program the 93C56.
Any help?

thanks. :beer:

As far as I know... "FU" means that you " F*cked Up " the EEPROM :D

You need to reflash it again. Use MPROG. You can find the dumps here in the forum.

Also, ATMEGA might be compromised. If so, you should reflash it again. Dumps are also available.

Good luck.

[Africa]

I've been reading a 93c46 eeprom, but my interface contains 93C56.

Is there anyone who can help me?

thanks

[Artilect]

Try with this VAG-COM Revival to properly recognize the device. Then load new dump with MProg.

BR

[Africa]

Try with this VAG-COM Revival to properly recognize the device. Then load new dump with MProg.

BR

thanks. i test tomorrow.

[bernieheu]

thanks from me

[k0mpresd]

thanks. used files in first post and all fixed up. :alberteinstein:

[tawaf11]

thanks im test and work perfectly vag com 908 en

[1 6 D]

Actual free English dual is for VCDS 11.11.0 is in this post:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index205.html#post1647476


Here is loader if it's RL clone:
http://www.digital-kaos.co.uk/forums/f152/vag-com-vcds-everything-99750/index205.html#post1644621

[bahlawi]

hi
i have vag com 908 not work with car
please hilp me thanks

[gelomeloman]

hi
i have vag com 908 not work with car
please hilp me thanks

Reprogram Atmega but first erase it and then flash and eeprom and fuse/lock bits

[george20vt]

Hi im looking for a ept dump for vag cable 113

[leolux]

Hi,

i have an perfect working cable from sklad how i can dump it to take it here online its the newewst 11.11.5 DRV GErman version

Leo

[gelomeloman]

You needt to read flash and eeprom file from Atmega162 from your cable. You can use Ponyprog or UPA (if you have it).
Ponyprog is easy to use - feev connections nad free LPT port on PC and go

[spider-wifi]

Hi all
Someone corect working dump for ATMEGA162 the Czech version?
10.6.4 and newer?
I do not want it free ...PM

thx

[snatchme]

Hello,

I have here an original VCDS interface but it stopped working.

Was working on a SEAT re-coded original Touchscreen radio. everithing went O.K. wanted to go to Instrument cluster for service reset.
and get the Message "not plugged into car".
did interface test, interface found and connected but not plugged into car message.
Green light is "On" did check with 2 laptops and 2 cars always same message.
have last SW on laptop and last Firmware on interface. do you know how to get it running again?

I have FTDI232RL inside with USB VID 0403 and PID FA24.

I have also tried to contact ross-tech but they do not reply to my e-mails.

Thanks for helping.
Greetz
Snatchme

[giskard3333]

Thanks!!! i really needed it

[giskard3333]

i been looking for the vag revival for a long time thanks

[alldecode]

189116189117

I have interface for VCDS like on picture

ver 11.11

but not work

led flashing red, when conect to car its green, but sw not see cable

VID 0403 PID FA24

on interface missing 7805, atmega is on usb power, and no GAL chip

wich version to update on this cable to work OK?

thanks

[mattydr67]

Mate
This tool comes with a dedicated VCDS softwear.
If I know well it is v11.11.3
Did you use this one?
And please share pics with the message that you show after you do TEST
and from ABOUT
Maybe you do something wrong and you do not need to reflash the Atmega
BTW this is the worst tool made VCDS made in China I ever seen
Good luck

[mladen76]

Everything to cut expence and to improve profit...
I guess price is the same like one that have all chips :evil:
My advice-send them back that shit they send you if you have a chance to get money back...

[alldecode]

yes, I sent back 4 peaces, and pay post, i have refund money, but last week i recive back packet with this cable (becouse wrong adress) then I try to repair.

189233

this is error message from sw 11-11-3

[alldecode]

yes, I sent back 4 peaces, and pay post, i have refund money, but last week i recive back packet with this cable (becouse wrong adress) then I try to repair.

189233

this is error message from sw 11-11-3

USB\VID_0403&PID_FA20.DeviceDesc="Ross-Tech HEX or KEY USB Interface"
USB\VID_0403&PID_FA23.DeviceDesc="Ross-Tech Micro-CAN Interface"
USB\VID_0403&PID_FA24.DeviceDesc="Ross-Tech Direct USB Interface"
USB\VID_0403&PID_DF20.DeviceDesc="Ross-Tech USB Converter"
USB\VID_0403&PID_FA30.DeviceDesc="Ross-Tech Direct Interface"

this is part from rt-usb.ini file, I try put all of then, but same problem.

mybe atmega ic clear, ... In first start program, and conect vcds to usb, vcds try to find driver, but driver not find, PID is wrong, I dont know which PID is writen to cable

someone who have flash and ept file, then I try to reprogram. Mybe then work

[mattydr67]

For your interface the VID/PID must be this:
USB\VID_0403&PID_FA30
Use MProg and change the FA24 into FA30
Then must be recognized.
Good luck

[mexanico1971]

why I can not program the fuses and the bit"s ?!
I bean able to erase the AT162 but not write it !
UPA ori say"s that is successfully programmed but is not !
what possible could be ?!
BR

[alldecode]

Ok, "mattydr67 (http://www.digital-kaos.co.uk/forums/members/8710-mattydr67/)", i put FA30

but, when i first run, i run over sw 11.11 (becouse i dont now that is 11.11.3), in 11.11 driver is not FA30, my mistake

look

now i change PID

end this is error message:

189290

what now?

[alldecode]

in one cable give mi this error:

sw is 1.84 and upgrade to 1.91, then upgrade is over, cabal works

189298

now i have 3 peaces, and try to directly flash with 1.84 (11.11) then upgrade, maybe be sucess

[mattydr67]

Mate use the softwear that comes with interface.
That kind of tool that you have it is usually sold with VCDS 11.11.3 softwear.
As I allready told you the VCDS 11.11. it is generic. There's 11.11.0 version, 11.11.1, .....11.11.5
And your tool dump works just one version of VCDS that comes with the interface not with other.
That's why it said "Interface Not Found"
Good luck

[alldecode]

"mexanico1971 (http://www.digital-kaos.co.uk/forums/members/86975-mexanico1971/)"

I programing atmega with pony, and is OK

try to ponyprog, are you have schematic for interface?

[alldecode]

OK, matty... but if i have newer sw, like 11.11.4 and higer, that sw upgrade interface without directly flash atmega?

[mattydr67]

No mate
The softwear upgrade just the firmwear in the Atmega.
And this just if you have a not blacklisted serial in the Atmega eeprom
I suppose you have a blacklisted serial so you cannot upgrade it.
If you allready tried this then you need to reflash your tool with a dump and use the version of VCDS for that dump.
Good luck

[alldecode]

did you have maybe 11.11.3 dump to try reflesh atmega (i have 11.11)

[mattydr67]

Mate
I have of course but dumps aren't for share
Sorry
Good luck


P.S. - the last free dump you can find it is for VCDS 11.11.0
If you have a RL tool you need a loader too

[alldecode]

I have dump 11.11, and tomorrow try tu upload to atmega, then change fireware with vcds. Maybe sucess

what you mean: If you have a RL tool you need a loader too

[mattydr67]

VCDS are with FTDI BL/BM or with FTDI RL
Fot the tool with FTDI BL/BM you don't need loader, for the tool with FTDI RL you need loader
Good luck

[alldecode]

OK, loader

i try to conect with car, and OK, but if i try to coding, error mesage... not registred ... on CD not find loader, do you have?

I buy many VCDS from china, and never use loader, why loader must use?

[mattydr67]

The tools with RL from China use their softwear for that tool.
Loader including or it is made in other way.
The loader it used when you use let's say VCDS 11.11.0 with original softwear but for the tool with RL ( becasue the dump in VCDS 11.11.0 it is for tools with FTDI BL/BM and no FTDI ID - FTDI RL has an ID so the loader will pass it )
Good luck

P.S> - your tool need to be reflashed

[betonel]

Tested VCDS 11.11.0 dump

hex files are for pony prog, bin files for upa.

Here you can find dump (Atmega flash+eeprom)

Use VCDS 11.11.0 loader if you have a RL interface. Remove rar extension from filepart of VCDS software.

When programming, keep in mind correct order:

1. CHIP ERASE
2. FLASH
3. EPROM
4. FUSE BITS
5. LOCK BITS


VCDS v11.11 ATMEGA162 Fuses & Lock bits
---------------------------------------


# LOCK: 0b11111100
# bit 7 = -
# bit 6 = -
# bit 5 = BLB12 (1)
# bit 4 = BLB11 (1)
# bit 3 = BLB02 (1)
# bit 2 = BLB01 (1)
# bit 1 = LB2 (0)
# bit 0 = LB1 (0)


# EFUSE: 0b11111001
# bit 7 = -
# bit 6 = -
# bit 5 = -
# bit 4 = M161C (1)
# bit 3 = BODLEVEL2 (1)
# bit 2 = BODLEVEL1 (0)
# bit 1 = BODLEVEL0 (0)
# bit 0 = -


# LFUSE: 0b11111101
# bit 7 = CKDIV8 (1)
# bit 6 = CKOUT (1)
# bit 5..4 = SUT1:0 (11)
# bit 3..0 = CKSEL3:0 (1101)


# HFUSE: 0b11011100
# bit 7 = OCDEN (1)
# bit 6 = JTAGEN (1)
# bit 5 = SPIEN (0)
# bit 4 = WDTON (1)
# bit 3 = EESAVE (1)
# bit 2 = BOOTSZ1 (1)
# bit 1 = BOOTSZ0 (0)
# bit 0 = BOOTRST (0)

[damian475]

Have someone some neewest flash and ee for 11.11.3 pl? i have 10.5.5 but looking for somethink new.

[eliotroyano]

Tested VCDS 11.11.0 dump

hex files are for pony prog, bin files for upa.

Here you can find dump (Atmega flash+eeprom)

Use VCDS 11.11.0 loader if you have a RL interface. Remove rar extension from filepart of VCDS software.

When programming, keep in mind correct order:

1. CHIP ERASE
2. FLASH
3. EPROM
4. FUSE BITS
5. LOCK BITS


VCDS v11.11 ATMEGA162 Fuses & Lock bits
---------------------------------------


# LOCK: 0b11111100
# bit 7 = -
# bit 6 = -
# bit 5 = BLB12 (1)
# bit 4 = BLB11 (1)
# bit 3 = BLB02 (1)
# bit 2 = BLB01 (1)
# bit 1 = LB2 (0)
# bit 0 = LB1 (0)


# EFUSE: 0b11111001
# bit 7 = -
# bit 6 = -
# bit 5 = -
# bit 4 = M161C (1)
# bit 3 = BODLEVEL2 (1)
# bit 2 = BODLEVEL1 (0)
# bit 1 = BODLEVEL0 (0)
# bit 0 = -


# LFUSE: 0b11111101
# bit 7 = CKDIV8 (1)
# bit 6 = CKOUT (1)
# bit 5..4 = SUT1:0 (11)
# bit 3..0 = CKSEL3:0 (1101)


# HFUSE: 0b11011100
# bit 7 = OCDEN (1)
# bit 6 = JTAGEN (1)
# bit 5 = SPIEN (0)
# bit 4 = WDTON (1)
# bit 3 = EESAVE (1)
# bit 2 = BOOTSZ1 (1)
# bit 1 = BOOTSZ0 (0)
# bit 0 = BOOTRST (0)

Betonel can you check fuse & lock bits because I have seen others in the past. Please check out attachment.259357

[eliotroyano]

Betonel can you check fuse & lock bits because I have seen others in the past. Please check out attachment.259357

Anyone can confirm the fuse & lock bits posted for VCDS 11.11.0?

[Marecki]

Tested VCDS 11.11.0 dump

hex files are for pony prog, bin files for upa.

Here you can find dump (Atmega flash+eeprom)

Use VCDS 11.11.0 loader if you have a RL interface. Remove rar extension from filepart of VCDS software.

When programming, keep in mind correct order:

1. CHIP ERASE
2. FLASH
3. EPROM
4. FUSE BITS
5. LOCK BITS


VCDS v11.11 ATMEGA162 Fuses & Lock bits
---------------------------------------


# LOCK: 0b11111100
# bit 7 = -
# bit 6 = -
# bit 5 = BLB12 (1)
# bit 4 = BLB11 (1)
# bit 3 = BLB02 (1)
# bit 2 = BLB01 (1)
# bit 1 = LB2 (0)
# bit 0 = LB1 (0)


# EFUSE: 0b11111001
# bit 7 = -
# bit 6 = -
# bit 5 = -
# bit 4 = M161C (1)
# bit 3 = BODLEVEL2 (1)
# bit 2 = BODLEVEL1 (0)
# bit 1 = BODLEVEL0 (0)
# bit 0 = -


# LFUSE: 0b11111101
# bit 7 = CKDIV8 (1)
# bit 6 = CKOUT (1)
# bit 5..4 = SUT1:0 (11)
# bit 3..0 = CKSEL3:0 (1101)


# HFUSE: 0b11011100
# bit 7 = OCDEN (1)
# bit 6 = JTAGEN (1)
# bit 5 = SPIEN (0)
# bit 4 = WDTON (1)
# bit 3 = EESAVE (1)
# bit 2 = BOOTSZ1 (1)
# bit 1 = BOOTSZ0 (0)
# bit 0 = BOOTRST (0)


zip archives damaged

[dimet]

Tested VCDS 11.11.0 dump

hex files are for pony prog, bin files for upa.

Here you can find dump (Atmega flash+eeprom)

Use VCDS 11.11.0 loader if you have a RL interface. Remove rar extension from filepart of VCDS software.

When programming, keep in mind correct order:

1. CHIP ERASE
2. FLASH
3. EPROM
4. FUSE BITS
5. LOCK BITS


VCDS v11.11 ATMEGA162 Fuses & Lock bits
---------------------------------------


# LOCK: 0b11111100
# bit 7 = -
# bit 6 = -
# bit 5 = BLB12 (1)
# bit 4 = BLB11 (1)
# bit 3 = BLB02 (1)
# bit 2 = BLB01 (1)
# bit 1 = LB2 (0)
# bit 0 = LB1 (0)


# EFUSE: 0b11111001
# bit 7 = -
# bit 6 = -
# bit 5 = -
# bit 4 = M161C (1)
# bit 3 = BODLEVEL2 (1)
# bit 2 = BODLEVEL1 (0)
# bit 1 = BODLEVEL0 (0)
# bit 0 = -


# LFUSE: 0b11111101
# bit 7 = CKDIV8 (1)
# bit 6 = CKOUT (1)
# bit 5..4 = SUT1:0 (11)
# bit 3..0 = CKSEL3:0 (1101)


# HFUSE: 0b11011100
# bit 7 = OCDEN (1)
# bit 6 = JTAGEN (1)
# bit 5 = SPIEN (0)
# bit 4 = WDTON (1)
# bit 3 = EESAVE (1)
# bit 2 = BOOTSZ1 (1)
# bit 1 = BOOTSZ0 (0)
# bit 0 = BOOTRST (0)

Please update damaged archives

[simaservis1108]

Since my VCDS was bricked,I used above dump 11.11.0.
Interface is alive now,but when I connect to CAN,I can work 10 seconds,then I am disconnected,and have to unplug/replug USB and restart VCDS.

Is there any solution to this?

[kidloco]

Hello to all i have a vcds interface 12.10 clone with beta sw. is there any version of vcds original software that can be used on this interface..Thank you

[PhoenixRSC]

Hello kidloco,

With VCDS chinese clone interface, you must only use the install executable that come with interface on CD-ROM.
There is a risk to block the interface if you try an another install executable.

[gazvts]

dumps for 12.12.0 on the web

[kidloco]

Please i need info how to make VCDS 12.10 with FTDI RL to any original VCDS Version example 11.11.0. thank you

[paro44]

Look at the big "vcds everything" thread, you can find there the aminebot tutorial for repair.
You can't make an original, since the public serials are blacklisted in software. Software update an internet connection will disable your interface.

[kidloco]

Thx, i was lokking there but could not find aminebot tutorial ,, plase can you give me a link or ...

[volk]

Hello. I need advice for relfashing atmega vie LPT. I can write eeprom but can't write flash.Witch format do I have use .bin or .hex? Thanks.

[ola98]

hello,

is possible to repair china cable vag912 ?

[gopelhu]

Hi all,

Here is my solution, ENJOY !!!

config with ponyprog, and installer very big size and i caanot upload it.

if anybody need it pl write me pm.

Regards,

[tehnards]

Hi there,

New here, due to a bricked Chinese vag-com interface 11.11 :/

Made a stupid mistake. Looking to see if I can just use vag-com revival to reprogram or if I need to do much more. Sorry, I know these are noob questions.

[Gizimo]

Hello, I have a HEX + CAN DUAL-K CAN USB interface.
Unfortunately, I have used a newer VCDS software and it asked me for a FW update from 1.92 to 1.94. Now unfortunately gone Something wrong and he accepts the connection but no longer recognize the interface.
The FTDI FT Prog recognize it perfectly. Can anyone help to liven up the part to me again?

Device Info from FTDI:
Chip Type: FT232R
Vendor ID: 0x0403
Product ID: 0x6001
Product Desc: Ross-Tech
Location ID: 0x11
EEPROM Type: 93C56 EEPROM

Hope it can someone help.

348823348824

[Gizimo]

Am I in the right place in the category? Any ideas what is wrong with the cable now?

I would be really grateful for your solutions.

[Gizimo]

Is there someone who can help?

Gesendet von meinem C6603 mit Tapatalk

[Gizimo]

push

Gesendet von meinem C6603 mit Tapatalk

[tango]

if original software used then your atmega has been wiped
you need to reprogram the interface
look inside interface and see what mcu is there if atmega your ok and can fix but if nec then best buy another

[Gizimo]

Big Thanks Tango, for your Help.
Chip is an
ATMEGA162
16AU
1308H
https://uploads.tapatalk-cdn.com/20160102/349f59f0744af8dcb71906f8a9a62e25.jpg

https://uploads.tapatalk-cdn.com/20160102/9d139f97f20be9a8f505a5996883c0eb.jpg

Gesendet von meinem C6603 mit Tapatalk

[mattydr67]

@Gizimo
First of all as I can see in the pics shared by you your tool is sklad66 vcds hq clone.
Secondly its right that it shows you vid/pid 0403/6001
Do not touch it. You will damage it.
Ok you loosed the warranty because you open it.
Now let me know what softwares version for vcds did you used and from where?
That tool is working only with sklad66 cracked software so do not use any other kind of vcds versions craked or not.
Good luck

[Gizimo]

My brother gave me the stuff.
But apparently wrong software, because he could not find the CD.
He gave me "VCDS-DRV-11115-Installer.exe", but the thing just would not be installed. On my XP laptop.
I tried it then with "VCDS15070DE-Setup.exe".
He told me it was all original. That's why I made the ~~~~ FW update from 1.92 to 1.94.
Then the interface disappeared in the recognition.

I thank you so much for the help.
I hope I have the brother not to buy a cable.

[mattydr67]

Hi
Don't worry about firmware upgrade. This is not the reason that the tool is not working now.
The reason is that you don't use the right software for it.
On one side there is a s/n. You can contact sklad66 maybe will help you.
Who knows. Anyway if you didn't touched the tool in anyway. I mean if you didn't reflashed the ftdi with ftprog and much more then this if you didn't touched the Atmega162 MCU tring to reflash it then could be a hope to make it works again.
Good luck

[Gizimo]

I have not changed anything on the device. I've googled Slkad66. Sklad66.com is offline. Does anyone know a way to repair the unit?

Gesendet von meinem C6603 mit Tapatalk

[mattydr67]

Mate you don't follow me at all
I told you that if you didn't touch it you didn't brick it.
So you don't need to fix it you only need the vcds software for your tool.
But versions after 14.10
Good luck

[Gizimo]

Sorry, my English is not so good. I just make me worry, because before the FW update the original software has found the interface and recognize the cable. Now the cable is only detected by FTDI.

Where can I find the right software?

[mattydr67]

Where can I find the right software?
Good question. From one who have it and wants to share it.
Good luck

[gazvts]

Hmm these tools never shipped with cd but if you send me pic outer case in pm i might share 1 version to try but only if you send me them pic in private

[konekt]

thanks for help

[dan5588]

Hi all,
I have a DUAL-K CAN USB VAG/ISO chinese interface.
back label "VCDS1103"
inside is:
FT232BL
ATMEGA162-16AU
EEPROM: 93C46
PALCE16V8H-10JC/4
MCP2515
MCP2551
7805
windows device manager say:
FTDIBUS\VID_0403+PID_6001+5&2C5C6891&0&8\0000
FTDIBUS\COMPORT&VID_0403&PID_6001

Unfortunately, I have used a wrong VCDS software
Need to reprogram the interface and suitable VCDS software
Please if you can help me with hex and everything needed. (fusebit setting for PonyProg...)
Thanks a lot!

[JBLSteeve]

Hi all,

I have a interface working with a french version of VCDS. I have let it to a friend and i try to use it with an official version. Now my interface doesn't work. I have the message not connected to the car. (I see that the led stay blank)
Do you have an idea to try to repair it. (I have made a record of the atmega with my usbasp some time ago with extreme burner air, but it's seem to be not enough.

Thanks

[mattydr67]

Share few pics mate with your error and tell us if the serial is Unregistred.
You have a clone that cannot works with untouched original sof~~~~e with a cloned serial
(blacklisted)
In this case its erased and you need a dump fora version of vcds
As I know this you will cannot find it for free and even if you wanna buy it
A dump it will be very expencive and it will not worth.
The better way for you is to find a HQ cline that cannot be damaged and you can upgrade it and use original softwares to upgrade it.
Or buy a genuine tool
Or buy another clone as yours and take care in the futhure
Good luck

[JBLSteeve]

Share few pics mate with your error and tell us if the serial is Unregistred.
You have a clone that cannot works with untouched original sof~~~~e with a cloned serial
(blacklisted)
In this case its erased and you need a dump fora version of vcds
As I know this you will cannot find it for free and even if you wanna buy it
A dump it will be very expencive and it will not worth.
The better way for you is to find a HQ cline that cannot be damaged and you can upgrade it and use original softwares to upgrade it.
Or buy a genuine tool
Or buy another clone as yours and take care in the futhure
Good luck

Thanks for your quick answer, i will make some capture connected to the car. But it's a french version. The message explain that interface is connected to PC, but not plug into the car. (It's strange that my led is stay off) I would like to test the regulator.
http://img15.hostingpics.net/thumbs/mini_491518IMG5505.jpg (http://www.hostingpics.net/viewer.php?id=491518IMG5505.jpg)
http://img15.hostingpics.net/thumbs/mini_379689IMG5506.jpg (http://www.hostingpics.net/viewer.php?id=379689IMG5506.jpg)

[mattydr67]

Hi
If the led its off even you plug it to the car
- no supply voltage ( bad connection )
- 7805 ( voltage regulator ) is defective
- wire defective
- Atmega not flashed ( or bad flashed )

Check it
Obe question please. After you trued it with original software you realized that the led its alwys turned off?
And the vid/pid was changed maybe

Good luck

[JBLSteeve]

Hi
If the led its off even you plug it to the car
- no supply voltage ( bad connection )
- 7805 ( voltage regulator ) is defective
- wire defective
- Atmega not flashed ( or bad flashed )

Check it
Obe question please. After you trued it with original software you realized that the led its alwys turned off?
And the vid/pid was changed maybe

Good luck

Today i check the regulator and the 5V is ok.
When i put the 12V i have 1s the led on and after it stay off.
For the vid/pid i don't know the one before.
I put back the VCDS version link to my cable and i still have the issue.
For the bad flashed do you think the flash with "eXtremeBurnerAVR" is bad ?

thanks

[dindisa]

If bought sklad66

email:
skype:

NO PERSONAL INFO IN POSTS !!!

[mattydr67]

@JBLSteeve
Maybe yes.
Maybe you didn't set the fusebits or not set item corectlly
Check it again
You can show us how did you set the fuse bit ( pics )
Good luck

[Charso]

Just want to post a "Hello" and thank you, I'm new to the site and finding it very usefull! Thank you all

[olegdon]

Hallo,I need tutorials to make VCDS interface from Chinese clone ELM 327 USB v1.5a.Could some people help me please with it...was trying to download that VCDS all rar.file, but got a mistake.Thx.

[mattydr67]

Its imposible mate
To diffrent kind if tools
ElM327 is using PIC MCU and VCDs is using Atmega MCU
This is just first major diffret.
Actually ELM327 is 100% diffrent then a VCDS Hex-Can
Good luck

[JBLSteeve]

@JBLSteeve
Maybe yes.
Maybe you didn't set the fusebits or not set item corectlly
Check it again
You can show us how did you set the fuse bit ( pics )
Good luck

I write the fuse buts with extreme burner
see the attached file.

[JBLSteeve]

Now, i have no answer of my atmega. I will change an reload it.
Can you tell me the best way and the best dump to use?

[mattydr67]

You flashed wrong fuse bits
If you bootloader is 256 words you can set the fuse its as below
CD DC F9 FF(CC)
If you bootloader is 512 words you can set fuse bits as below
CD DA F9 FF(CC)
Good luck

[JBLSteeve]

You flashed wrong fuse bits
If you bootloader is 256 words you can set the fuse its as below
CD DC F9 FF(CC)
If you bootloader is 512 words you can set fuse bits as below
CD DA F9 FF(CC)
Good luck

Thanks, but how can i identify my bootloader ?
Do you have an idea to find a dump for my atmega

[gopelhu]

189116189117

I have interface for VCDS like on picture

ver 11.11

but not work

led flashing red, when conect to car its green, but sw not see cable

VID 0403 PID FA24

on interface missing 7805, atmega is on usb power, and no GAL chip

wich version to update on this cable to work OK?

thanks


Here is the working dump for your interface...enjoy.....

[JBLSteeve]

Here is the working dump for your interface...enjoy.....

Thanks, i will try it this weekend.

[JBLSteeve]

I test this dump this morning, i have the message "Not connected to car".
Maybe I don't use the good fuse bit
CD DA F9 FF

[mattydr67]

Power the tool
And set the fuse bits CD DC F9 CC
Because it the fiwmare with b256 words
Don't forget to set the fusebit not only write it
When test the tool plug ut into the ca or power the 12v
Good luck

[JBLSteeve]

I update with those parameters CD DC F9 CC FFFFFF60if I power the cable per the ODB connector the led is blinking I thinks it's seem to be goodBut the vcds 11.11.3 still say interface not connected. I force a reinstall of the driver with same result. My id is 403 & FA24I test with my version 12.12.1 and the software see the cable and ask for an update to 1.92. Maybe I have to test with a dump of 1.92. Normally my original dump is 1.93 but do I have to use the same fuse?Thanks

[mattydr67]

Led blinking red this is not good
You did there a miskake before start flashing the tool
The 1.92 or 1.93 we cannot call it dump.
The Atmega dump means bootliader + firmware + eeprom
1.92 or 1.93 is firmware
Bootloader + firmware = flash
Eeprom is the serial
To flash an Atmega in VcDs you need flash+eeprom+fusebits
So take care what are you doing there
Do you have good eeproms for the vcds versions that you wanna use?
Think
Good luck

[gopelhu]

I test this dump this morning, i have the message "Not connected to car".
Maybe I don't use the good fuse bit
CD DA F9 FF


Hi,

here is the config bits with ponyprog only

Regards

[JBLSteeve]

I have the flash but I'm not sure for the eeprom

today my device is not working, and I don't know how to repair it.
If I understand I have to find a complete dump and vcds link to this eeprom.

[JBLSteeve]

I have a friend with same interface as mine, i will ask him to copy his dump.
Now i need to see him...

[mattydr67]

If he flashed hisbtool by himself then he can give you his dump
But if his tool is both as it is now then belive me that all he will read will not be good
Always the tools are protected by the fuse bits
Look if you are flash your tool with this fusebits
CD DC F9 FF the dump can be read with AVR
If you flash the tool with this fusebits
CD DC F9 CC the dump is protected and cannot be read it
Good luck

[JBLSteeve]

Thanks for this clarification, so we need to check the fusebit first.
If the avr is protect, we will have a message on extremburner when we read by ISP or the data read will be corrupt?

[mattydr67]

Mate I took a look at all previos post of you in this thread.
So as I see you have a chinese tool that works with vcds french versions
Your tools is a ftdi RL one
Well to flash it back with your friend dump even his tool hasn't set it the pretection fusebits you will not be able to use his dump
Because his dump is marriaged with his ftdi id
But for sure his dump Atmega its protected.
For the momement and for sure there isn't and maybe will not be any futhure french dump
The 11.11.0 dump shared here is god for your tool but you need to start the vcds with the loader for RL tools
You can try to find the vcds 11.11.5 or vcds 12.12.0 dump that comes with its specific craked vcs versions ( not with any other )
Good luck

[JBLSteeve]

Has you tell the fuse bit lock is FF so I can't read the flash and eeprom.
Do you think if I change the lock fusebit I will loss the flash and eeprom?
i don't want to kill the cable of my friend.

[mattydr67]

Read again carefully
I said CC is protected and FF not protected
You cannot change the fusebits and the to read your friend tool
You will erase it too
If you wanna an advise from me then think to flash your tool with a free dump or if you want a tool in french then buy a.new one
This was my last post in this thread.
Good luck

[abdelamjid]

hi all
thank you for sharing

i have an vcds 11.11 i search dump 12.12 work with french vcds french versions

thanks to all

best regards

[gopelhu]

Here are some eeprom contents...enjoy

[hsnlpy]

Hello folks.Here i publish pictures on my VCDS device.Bought it few years ago and accidentally updated it..As i know it is not original and firmware destroyed.I tried couple of dump files but the problem is "K1 : Shourt to ground".. Does somebody know how to fix it ? There is communication with parallel and usb port without issue..Please help me to fix it.. Thanks

Edit: Chip ft232BL

[gopelhu]

Hi,

What is type of U5 U8 U9 ic's? There are the problem "K1 : Shouth to ground"

You need to reprog the 93c46eeprom and Atmega162.

Regards,G

[hsnlpy]

Thanks alot gopelhu.. Could you explain me more easy how to do it ? also please send me files too.. Thanks in advance

[JBLSteeve]

I upload my atmega and put the fusebit.
The led is green when i put the 12V, but i have an error on the self-test.
Do you have any idea ?
362181362182

[dekiasd]

tnx for post

[gopelhu]

I upload my atmega and put the fusebit.
The led is green when i put the 12V, but i have an error on the self-test.
Do you have any idea ?
362181362182

Hi,

This error message is : Not plugged into car?

Yesterday I tested my two interface: one has v1.84 an other has v1.92 fw with v11.11.0 software and works perfectly.

Do you need to plug to the OBD and yoe need to communication once one car !!!! and save it !!!!

My solution works perfectly !!!! here is the software

https://mega.nz/#!AgcR1L5Y!Q4h4J1ZpBCduDsP0Qb6A_nkl64_1Qvm2faGfnpY mFWw

Pls do not use this exe vcds11110_fixR.exe from the rar!!! it is important !!!

Regards, G

[pantarei]

Regards to you.
question: Are there any dump files for VC 11.11.3?

[gopelhu]

Hi all,

I share my other solution for vcds 12.12.x.

Today I created the ATmega162 dump and works perfectly 100% !!!

Step-by-step:

Pls install only this installer: VCDS-Release-12.12.0-Installer English 512bits.exe !!!!

When you installed, pls upload the ftdi232rl.ept file to the FTDI FL232RL ! Important !!!

This solution works with vcds interface that's has a FT232RL ic.

After rund the vcds 12.12.0 exe and pls go to options and pls push the test button, after save it.

This self-learning solution !!!

https://mega.nz/#!rI1jwJ5Z!8uTzANKm7aaRuFUGNSDo7fdEC032vqlRR488xZh a6O8

ENJOY !!!!

Regards, G

[1 6 D]

Long coding works?

[JBLSteeve]

Hi all,

I share my other solution for vcds 12.12.x.

Today I created the ATmega162 dump and works perfectly 100% !!!

Step-by-step:

Pls install only this installer: VCDS-Release-12.12.0-Installer English 512bits.exe !!!!

When you installed, pls upload the ftdi232rl.ept file to the FTDI FL232RL ! Important !!!

This solution works with vcds interface that's has a FT232RL ic.

After rund the vcds 12.12.0 exe and pls go to options and pls push the test button, after save it.

This self-learning solution !!!

ENJOY !!!!

Regards, G


Thanks it's work with my interface. I test a scan and an erase of error, perfect.

[eliotroyano]

Hi all,

I share my other solution for vcds 12.12.x.

Today I created the ATmega162 dump and works perfectly 100% !!!

Step-by-step:

Pls install only this installer: VCDS-Release-12.12.0-Installer English 512bits.exe !!!!

When you installed, pls upload the ftdi232rl.ept file to the FTDI FL232RL ! Important !!!

This solution works with vcds interface that's has a FT232RL ic.

After rund the vcds 12.12.0 exe and pls go to options and pls push the test button, after save it.

This self-learning solution !!!

ENJOY !!!!

Regards, G

Any solution for FT232BL/BM?

[gopelhu]

sorry but i dont have more free times, maybe weekend :)

[fantomel]

Nice to see the dumps i shared here :) after so long time.
That 12.12.0 it's not working on long coding and adaptation, but same dumps works also on 11.11.5 that i posted in other forums for free for all.

[abdelamjid]

can you help me how to update my vag 11.11. to 12.12

thanks to all

best regards

[eliotroyano]

I have tested FT232BL/BM V12.12.0 and V11.11.5 posted by Fantomel but most of the time doing logs connection last some seconds only. I have test 2 cables with same problem. Do you know what can cause this problem?

[gopelhu]

I have tested FT232BL/BM V12.12.0 and V11.11.5 posted by Fantomel but most of the time doing logs connection last some seconds only. I have test 2 cables with same problem. Do you know what can cause this problem?

Hi

The FT232BL/BM differents content wit FT232RL, pls do not try it.

I will create the content to FT232BL/BM, pls wait untill i will finished and tested it/them.

Regards, G

[gopelhu]

can you help me how to update my vag 11.11. to 12.12

thanks to all

best regards


Hi, pls upload your interface pcb top and botton sides.

Regards, G

[eliotroyano]

Hi
The FT232BL/BM differents content wit FT232RL, pls do not try it.
I will create the content to FT232BL/BM, pls wait untill i will finished and tested it/them.
Regards, G

Ok great!!!!!

[gopelhu]

again i upload bec i lost my pc

[alexm1]

It is not clear, this is for FTDI BM/BL?
thanks for you work and time!

[ikara]

It is not clear, this is for FTDI BM/BL?
thanks for you work and time!

RL as i see

[gopelhu]

It is not clear, this is for FTDI BM/BL?
thanks for you work and time!


Hi,

No, its FT232RL, but this weekend i will finished my solution

Regards all

[alexm1]

I tried to split .bin from the rar, into the flash.hex +eeprom.hex, using ponyprog2000, but when I open eeprom file with xtremeburner it says: "This file is too large for selected AVR microcontroler..."
What I am doing wrong?

edit: my bad, old version of pony, tried latest version and job done.
Cable works ok, not tested yet for long coding.

L.E. too bad, long coding not working[emoji20] .

[abdelamjid]

thank you for sharing

plz help me how to flash my vcds 11.11 ( china clone )

mcu: D79F8513A
MCP2512
FTDI:ft232bl
thanks
best regards

[fantomel]

that is a nec mcu, no hope for that for any upgrades. Ori interfaces had and have Atmega162 processor and not NEC. That is a ~~~~ cook made by chinese :)

P.S. The dumps i posted work on bm,bl,rl chips without any problems with those versions of programs.

[danielgatan]

368862Hello mates! I try to reflash my interface 11.11 with upa usb...i can read read and program.. after programming say programming succes...but if i try to verify i have error and when i read i have dump empty.."like in pitures" lock bits and fuse i use that from pictures368857368858368859

[cocutanu]

It's normal you can not verify Atmega. Once you wrote it with fuses it gets locked.
So, you'll not be able to read it again for verifying.

[alexm1]

@danielgatan
After reflash your cable it is working????
It is true that after reflash your dump will be encripted but can not be "empty".

[eliotroyano]

that is a nec mcu, no hope for that for any upgrades. Ori interfaces had and have Atmega162 processor and not NEC. That is a ~~~~ cook made by chinese :)
P.S. The dumps i posted work on bm,bl,rl chips without any problems with those versions of programs.

Thanks Fantomel I have tested your solution for V12.12 FT232BL but doing logging it only last some seconds and lost connection. Mainly happends with CAN cars. Two laptops and two BL cables was tested with same results. Do you have an idea what can be wrong?

[abdelamjid]

thank you fantomel

best regards

[abdelamjid]

that is a nec mcu, no hope for that for any upgrades. Ori interfaces had and have Atmega162 processor and not NEC. That is a ~~~~ cook made by chinese :)

P.S. The dumps i posted work on bm,bl,rl chips without any problems with those versions of programs.


thank you for your response

[0n0t0le]

hello everybody. i have genuine ross-tech interface with revoked license. there is no way to register it. it is blacklisted by ross-tech. There are atmega162 and ftdi 232RQ inside. Is there any solution to make it works?

[loveya]

hopefully this will work for me

thanks

[MacNB]

Have a VAG 11.11 cable for a while (18 months).
Worked fine (could read codes, reset DTC's, change Long Coding, etc).

Recently, it seems it has become locked out saying certain functions need a license now.
I can only think that the Wi-Fi was on when I last used it and the VCDS 11.11 s/w has re-programmed the cable and blocked it.

Looking for help to see if it can be salvaged.
The chips on the board are:

ATMEGA162
GAL16V8B
93C56WP

FT232BL
MCP2515
TJA1050

Plus there's one empty chip pad set. See pics:


http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=371808&d=1461615775&thumb=1 (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=371808&d=1461615775)http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=371809&d=1461615822&thumb=1 (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=371809&d=1461615822)

If it can be re-programmed, any pointers would be great (which programmer to buy, wiring the programmer, which dumps, etc). Once I have all the bits (H/W & S/W), I'll write up a guide as I cannot find one that is in one place. Thanks.

[gopelhu]

hello everybody. i have genuine ross-tech interface with revoked license. there is no way to register it. it is blacklisted by ross-tech. There are atmega162 and ftdi 232RQ inside. Is there any solution to make it works?

Can you upload some pics for your interface?

To All,

I have a BM/BL 93cxx dump but i dont have any interface to test it, I have 3pces RL .... GRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR

Maybe if i get one, i will test it and upload the ept file.

Regards,G

[MacNB]

Still looking for help to repair my cable (with ATMEGA162, GAL16V8B, 93C56WP, FT232BL, MCP2515, TJA1050) .
Looking for the dumps for 11.11.
Device manager tells me the cable VID=0403 and PID=FA20.

[mikesisk2008]

what do i need to reprogram this... it says vag12.12 on the outside case. thanks372350
372351

[hremus]

I have an issue with one vcds 12.12.0 interface. After a low batery voltage on a car, my interface does not respond. On VCDS test it say "Interface not found error -99". This hapend a year ago, and it was fixed by the seller of interface for free (warranty). This happend again, last week. When I connect to USB, an over current error ocured. I open it, and the FT232RL chip was hot,(hot enough to remove itself from pcb). I orderd a new FT232RL chip, solderd in place, progrmmed with mprog. When I tested on VCDS now, it say "Interface found and not conected to car". When I connect it to car, the led stay red for 1 sec and after become green. If I test it now, it say "Interface not found".Try to open a connection with car (ECU) and appears error -2 no communication.
Any ideea how to fix my VCDS 12.12.0 interface?

[mesterel]

OK I have a Dual-K & CAN Vag11.11 too with the same connection problem. It get's disconnected every 5 seconds. I've used lots of dumps from this forum but no one works fine for me. I uploaded some pics with it.

373652373653

[umitasa]

still no LED's , i write the dumps, thee eeprom snd the flash on atmega, but still the LEDS are not powering up 7805 is working any other ideas?

[mesterel]

@umitasa I'm pretty sure your Atmega162 is clean or the dumps used are not the good ones. If your vcds worked before you have to try other dumps. What type of programmer did you used to flash the chip? What soft?

P.S: In time you write the dump on Atmega chip the led is blinking red?

[gopelhu]

Hi all,

some peaple asked me this VCDS 15.7.x atmega dumps.

I created a solutions this version, here is....

ENJOY all.... :)

I need to know working or not? If you have an installed version the you need to save a d1,d2,d3 bins
After install the v15.7.x version and copy the files and plug the interface with this dump and run the sw and check the about page.

Regards, G

[alexm1]

As I see, it is only for RL?

[gopelhu]

As I see, it is only for RL?

yes, it's ft232rl

[eliotroyano]

Hi all,
some peaple asked me this VCDS 15.7.x atmega dumps.
I created a solutions this version, here is....
ENJOY all.... :)
I need to know working or not? If you have an installed version the you need to save a d1,d2,d3 bins
After install the v15.7.x version and copy the files and plug the interface with this dump and run the sw and check the about page.
Regards, G

Gopelhu which V15.7.x version do you use? oem one? or where can I find it?

[marek128]

dont work. when plug dongle to supply interface not connected. without supply car not connected.

I tried china 11.11.3 unit

[gopelhu]

dont work. when plug dongle to supply interface not connected. without supply car not connected.

I tried china 11.11.3 unit

Ok, thanks for the info. I will create the d1,d2,d3 files and i will upload.

I see the interface found and the type of interface, its ok.

Later ......

Regards, G

[fantomel]

you can create 100 d1-d3 files because are useless. those files are just initial check , so smoke in the eyes of the user. That is all.
A good dump does not need d1-d3, it makes them on 1st test of interface and if is ok or not you see the sn green or not.

[kiyrik]

Gopelhu, thanks for vcds 12.12 dumps (from post (http://www.digital-kaos.co.uk/forums/showthread.php/237263-VAG-COM-VCDS-LATEST-DUMPS?p=2741680&viewfull=1#post2741680)). Now I alredy restore my china 12.12 cable with these dumps.
Cable have Atmega and ft232rl only (no GAL or ATF). So, I use provided SW (VCDS-Release-12.12.0-Installer English 512bits.exe) and flash atmega witch fw and eeprom.
No changes required for ft232. Atmega lock fuses leaved unprogrammed (disabled all locks).
I divide FW+EEPROM dump to separate files and convert its to Intel HEX, because I use AVERDUDE for flashing.

https://mega.nz/#!FB4xjbgA!51wHL0J_MzFhpSY-VlNrHVjRSHGrRjrzUPraXk-Kado

377016377017

[gopelhu]

I like that everyone is asking for help.
When I help everybody, then they are criticizing.
Now I stop my VCDS assistance.


Then when I get a request for help is what I wrote last time, resolving all my limitations.


Good luck for everyone !!!!

[marek128]

U doing great job mate, pls dont stop. 100 users like ur work 1 not. dont give UP bro.
NOTE:

In mcu eeprom is serial number with come sync to GAL/ATF they need to be from same unit not corrupted. Software PC check this. if not pass - unauthorized...


P.S. 12.12.0 CODING dont working.

[SchrodingersCat]

QUOTE=marek128;2773945]dont work. when plug dongle to supply interface not connected. without supply car not connected.

I tried china 11.11.3 unit[/QUOTE]

Hi marek128, I have the same issue with a "VCDS 15.7 VAGCOM 15.7 VCDS HEX CAN USB Interface VAG 15.7 with ATMEGA162" cable that I just bought.
I installed VCDS 15.74 off the rosstech website with wifi enabled. Then I tried the 15.7 version that came off the bundled CD. It says "Not plugged into car!". Could this have bricked it? Were you able to resolve this issue in the end?

379543[

[3cwired]

I have pretty much the same problem as you ^^ except I had already vcds 12 installed on my computer and didnt know it, plugged my cable in and now it says unlicensed when i use my cable with the software that came with the disk. I need help too.

I too have a vcds 15.7 cable and the same atmega chip

[fantomel]

All you need regarding restoring cables to level 12.12.0 (without long coding) and 11.11.5 working full (both with same dumps) you can find them in the collection i posted long long time ago ..... HERE (https://yadi.sk/d/zt5z2v9Nf9Zkt) OR HERE (https://yadi.sk/d/Iml-0q-Ef9bgW) the complete one including the 1st part.
No pass, just programs and stuff i gathered at that time.
These repairs work only with cables that have atmega162 processor not any other chinese inventions.

[SchrodingersCat]

QUOTE=marek128;2773945]dont work. when plug dongle to supply interface not connected. without supply car not connected.

I tried china 11.11.3 unit

Hi marek128, I have the same issue with a "VCDS 15.7 VAGCOM 15.7 VCDS HEX CAN USB Interface VAG 15.7 with ATMEGA162" cable that I just bought.
I installed VCDS 15.74 off the rosstech website with wifi enabled. Then I tried the 15.7 version that came off the bundled CD. It says "Not plugged into car!". Could this have bricked it? Were you able to resolve this issue in the end?

379543[[/QUOTE]


Hi! Thanks for the response fantomel. I manage to get the cable to work this evening. I beleive that the issue was as simple as I didnt have it plugged into the OBD connection far enough. I had the key in the vehicle, radio display on, but the ignition off. Once I removed the connector on the car panel and pushed the male connector of the cable firmly into it, the green LED on the cable lit. I was using windows 7 on a VM in OSX. I uninstalled VCDS and delected the RosCAM folder in My Programs. I then reinstalled VCDS to the My Documents directory. After installation, I plugged in the cable, mapped it to my VM, and the driver instadded autiomatically. THen I ran VCDS, went to Options, and tested the cable. It worked!

I am now able to enable AUX in on my Chorus radio on my Audi A4 8K B8.

Thanks for all your help.

[eliotroyano]

Mate I took a look at all previos post of you in this thread.
So as I see you have a chinese tool that works with vcds french versions
Your tools is a ftdi RL one
Well to flash it back with your friend dump even his tool hasn't set it the pretection fusebits you will not be able to use his dump
Because his dump is marriaged with his ftdi id
But for sure his dump Atmega its protected.
For the momement and for sure there isn't and maybe will not be any futhure french dump
The 11.11.0 dump shared here is god for your tool but you need to start the vcds with the loader for RL tools
You can try to find the vcds 11.11.5 or vcds 12.12.0 dump that comes with its specific craked vcs versions ( not with any other )
Good luck

Friends sorry to ask but for 11.11.5 and/or 12.12 with RL based interfaces using cracked sw we still need to remove STC based components and wire previous comments 4 wires (1 for atmega and 3 for MCP2515)????

[bdm]

Does anybody know how to "translate" and put new sn to eeprom? I've compared 2 versions and differences there are:

ver 1063
:10001000DE3085FFFFABFFFFFFFFFF02090000009E
ver 1065
:10001000DE3085FFFFFFFFFFFFFFFFFFFFFFFFFF5A

[vtince]

thanks, i will try

[mattydr67]

Friends sorry to ask but for 11.11.5 and/or 12.12 with RL based interfaces using cracked sw we still need to remove STC based components and wire previous comments 4 wires (1 for atmega and 3 for MCP2515)????
Yes of course
STC is for Atmega protection
So if you do not remove it then you cannot reflash it
One time I tried with STC not removed and it worked but I suppose that that SRC was defective
In all the other cases it was need to remove it
Good luck

[wecken]

Hi,

I have question about harware compatible from cable with 9.08 software and last version? Can I update my 9.08 to f.a. 12.12?

[azza2]

This is very userful to me. Thanks a lot.

[macalister]

vag com 908 thanks

[azza2]

Hi marek128, I have the same issue with a "VCDS 15.7 VAGCOM 15.7 VCDS HEX CAN USB Interface VAG 15.7 with ATMEGA162" cable that I just bought.
I installed VCDS 15.74 off the rosstech website with wifi enabled. Then I tried the 15.7 version that came off the bundled CD. It says "Not plugged into car!". Could this have bricked it? Were you able to resolve this issue in the end?

379543[


Hi! Thanks for the response fantomel. I manage to get the cable to work this evening. I beleive that the issue was as simple as I didnt have it plugged into the OBD connection far enough. I had the key in the vehicle, radio display on, but the ignition off. Once I removed the connector on the car panel and pushed the male connector of the cable firmly into it, the green LED on the cable lit. I was using windows 7 on a VM in OSX. I uninstalled VCDS and delected the RosCAM folder in My Programs. I then reinstalled VCDS to the My Documents directory. After installation, I plugged in the cable, mapped it to my VM, and the driver instadded autiomatically. THen I ran VCDS, went to Options, and tested the cable. It worked!

I am now able to enable AUX in on my Chorus radio on my Audi A4 8K B8.

Thanks for all your help.[/QUOTE]

Hi, which package of 15.7 do you use? I tried 2 packages of version15.7.x, failed to test the cable.

[azza2]

I have the same question.
Do you find the exact version?
Thanks!


Gopelhu which V15.7.x version do you use? oem one? or where can I find it?

[azza2]

Hi marek128, I have the same issue with a "VCDS 15.7 VAGCOM 15.7 VCDS HEX CAN USB Interface VAG 15.7 with ATMEGA162" cable that I just bought.
I installed VCDS 15.74 off the rosstech website with wifi enabled. Then I tried the 15.7 version that came off the bundled CD. It says "Not plugged into car!". Could this have bricked it? Were you able to resolve this issue in the end?

379543


Hi! Thanks for the response fantomel. I manage to get the cable to work this evening. I beleive that the issue was as simple as I didnt have it plugged into the OBD connection far enough. I had the key in the vehicle, radio display on, but the ignition off. Once I removed the connector on the car panel and pushed the male connector of the cable firmly into it, the green LED on the cable lit. I was using windows 7 on a VM in OSX. I uninstalled VCDS and delected the RosCAM folder in My Programs. I then reinstalled VCDS to the My Documents directory. After installation, I plugged in the cable, mapped it to my VM, and the driver instadded autiomatically. THen I ran VCDS, went to Options, and tested the cable. It worked!

I am now able to enable AUX in on my Chorus radio on my Audi A4 8K B8.

Thanks for all your help.


Hi man, which version do you use when you succeed? I flashed 15.7.x dump and failed with 15.7.4/15.7.1/15.7.0(all english language, 15.7.0 cannot be started software)

[alexm1]

Are you sure that you have used 15.7 good dump? I never see someone to confirm that dump to be free yet.

[azza2]

Are you sure that you have used 15.7 good dump? I never see someone to confirm that dump to be free yet.

I used the dump where posted on this thread page 12. here (http://www.digital-kaos.co.uk/forums/showthread.php/237263-VAG-COM-VCDS-LATEST-DUMPS?p=2773016&viewfull=1#post2773016)

[paro44]

See the following posts. It's not working. Gopelhu stopped support.

[azza2]

See the following posts. It's not working. Gopelhu stopped support.
I saw someone working, not sure it is 15.7.x?

which latest version I can get it work? Mine 12.12.0 can not change long code, also this 12.12.0 and 11.11.5 both can not access adaptation of instruments on my golf 6 which I could access by old version like 10.6.3/10.6.4 , and I cannot get any security access code for it.

[alexm1]

The last free dumps are for 12.12.0 (no long coding)/11.11.5.
As I know for 15.7.x no one confirmed to be a good dump.

[azza2]

The last free dumps are for 12.12.0 (no long coding)/11.11.5.
As I know for 15.7.x no one confirmed to be a good dump.

As I tried, the flash part is good, but the eeprom maybe have problem. I tried to combine other eeprom from other version I got before, failed.
BTW, I used the version 15.7.4 from the offical website.

Let me tell how I confirm the flash part is good.
When I tried 15.7.x dump with failure, I tried flash 12.12.x dump. It is working for software 12.12.0 eng. Then I tried software 15.7.4 to test cable without doing anything to the cable. 15.7.4 prompted me the flash version is 1.92, firmware update require. The I updated it with software 15.7.4, after that, I read the flash as new dump to compare with the dump I downloaded on page 12. They are not different. BTW, after updated by software 15.7.4, the eeprom data was changed few.

[azza2]

Hi all,

some peaple asked me this VCDS 15.7.x atmega dumps.

I created a solutions this version, here is....

ENJOY all.... :)

I need to know working or not? If you have an installed version the you need to save a d1,d2,d3 bins
After install the v15.7.x version and copy the files and plug the interface with this dump and run the sw and check the about page.

Regards, G

Feedback, the d1,d2,d3 bins copied after install will be deleted by v15.7.x when it is running v15.7.x testing operation.

Another question, how can I let it self learning working?

[azza2]

Mate I took a look at all previos post of you in this thread.
So as I see you have a chinese tool that works with vcds french versions
Your tools is a ftdi RL one
Well to flash it back with your friend dump even his tool hasn't set it the pretection fusebits you will not be able to use his dump
Because his dump is marriaged with his ftdi id
But for sure his dump Atmega its protected.
For the momement and for sure there isn't and maybe will not be any futhure french dump
The 11.11.0 dump shared here is god for your tool but you need to start the vcds with the loader for RL tools
You can try to find the vcds 11.11.5 or vcds 12.12.0 dump that comes with its specific craked vcs versions ( not with any other )
Good luck

Where can I get loader for RL tools for v15.7.4? I pm you to explan what it happenned to me. Thanks

[jgraf]

where is v15.7.4

[mattydr67]

Guys all you try it will not work anymore
You are waisting your times
You cannot combine anything
To make a tool works with a version you need a nt blacklisted serial or a loader that let a cloned serial working
The last dump that you can find for free is 11.11.5/12.12.0
A dump is not cheap but en you use clond serial you need diffrent loader for each version - no one will sell you a dump and then to provide a loader forch version
If we are talking about HQ clones that can upgraded with official vcds software then a dump if will be cloned then will be blacklisted. If you don't do this then you havto make a loader for each version.
This is the incovinient for the free stuff hunters
You have 2 chises guys
1.buy a clone that can be upgraded with cracked softwares and the supplier will provide you a new cracked version all the time
2.buy a clone that be upgraded using the official vcds software and you don't need to waith for cracked versions
But this kind of tool are not sell in public because all that will be sold in public will be killed
Good luck

P.S. - one of you do not take my advise its free to testin futhure all he think but each vcds version is uniq and cannot be combined

[liviudiaconu]

I used the dump where posted on this thread page 12. here (http://www.digital-kaos.co.uk/forums/showthread.php/237263-VAG-COM-VCDS-LATEST-DUMPS?p=2773016&viewfull=1#post2773016)

Is 11.11.5 ro-en/12.12.0 ro en dump. Bad dump.



For 15.7.4 need a good dump, a good loader and another few things. None for free.

[dESK0]

Try with this VAG-COM Revival to properly recognize the device. Then load new dump with MProg.

BR

Very useful, searching a good link for a long time. TX

[mattydr67]

New 16.8.0 version in some languages are already available
Working with genuine and some HQ clones
Good luck

[wimmerfield]

Can you message me which HQ clone(s) 16.8.0 works with please. TIA.

[spider-wifi]

Hi,

I am interested in VAG 15.7.x dumps of Czech language. Send offer to PM.

Thanks

[mattydr67]

Hi
VCDS SLO 16.8.0 in Czech language its available
But let me tell you that the original VCDS SLO 16.8.0 and also the VCDS SLO 15.7.3 has a bug
Its missing Long Coding button in CAN GATAWAY.
I tested few VW Passat cars B6 and B7
VCDS in all the other language it has that function ( button available )
The last VCDS SLO version that has that button available that i tested is VCDS SLO 12.12.3
If you asked me I have no dumps for sell.
Good luck
Matty

[silvinnio]

Hi,
I have VCDS 15.7.3 with FW 1.94 with no licence. I think by mistake connected to the internet and now :( . Can somebody help me with this?
Thank you in advance

[mattydr67]

I don't think that anyone can help you flashing your tool
we don't know what tool did you used BL or RLbut I'm very sure its RL
this mean that the chip Id it must be marriages with the ft I Id and if you didn't extract your dump before then I don't think th at someone can help you
much more of this who do you think that it spend time to extract Chinese ~~~~ tools dumps?
Because is there no reason this tools has no future. The clnd serial will be blacklisted and the cracked CDs has no internet protection
you can find a good dump and software in Mr.Fantomel collection the 11.11.5 vcdsversion and you can flash it and use it
But please share two pics with your both sides of PCB of your tool
let us know what kind of tool you have
Good luck

[jollepe]

I'd like to buy a chinese clone obdII connector. Which one can you recommend?
Therefore I want to flash a dump of an original dongle to the chinese interface?
Is it possible?
Thanks in advance

[silvinnio]

Hi,
I have ATMEGA 162 and FT232BL. I need to make this interface working for a Touareg 2013. Any ideas?
I did not tried to do any flash to this interface. Just used with internet on and now in blacklisted, I think. I receive error not Licensed. This has been already updated from ver 11 to 15.7.3 by the guy who sold me this interface.
Thank you in advance.

395351 395350

[jollepe]

As an addition to my previous post, I'd like to know, which configuration is the latest one which is working perfectly?
Which Dongle do I have to buy, and which software do I need?

[leckerez]

I want to buy chinese dongle. There are some with 15.7.1 software. Is there some hardware differences? Where can I find the schematics?

[mattydr67]

Hi
Any hardware that contain Atmega, GAL/ATF, FTDI, MCP and L9637D ( on k-line ) or tranzistors .
Noone cannot say wich has more quallity then other but all can be good.
Now about the software used and the chinese solutions I will advise you buy any.
Because chinese do n ot make:
- solutions that can be upgraded
- solution that has internet protections or similar solutions that will not let ross-tech servers to erase you license
And in this case you never know when you will not be able to use your tool because UNREGISTRED

Now about original dump
So in any of the chinese tools that contain Atmega you can flash a genuine dump
If you has a RL tool you need a loader that will pass the FTDI ID check
If you have a BL one you need a loader to pass the FTDI ID check
or you need a dump from a genuine tool with BM
But in all of this cases you need to stay away from internet no matter taht you will use the internet only when the tool is not plugged. In any moment when you have the internet connection turned on your vcds license is checked by ross-tech servers
In all of this cases the loader must pass the FTDI ID check and block the internet connection of vcds
In case that you will be "cach" you will not loose only the clone but you also will loose the genuine one
I do not advise you to do this
Good luck

[leckerez]

Hi Mattydr67,
thanks for the explanation.
What for is the GAL? are all device version have same GAL program?
So, I will order the one with 15.7.1 software and try it.

[mattydr67]

GAL/ATF is for Dual K-line cars
with other words CDs can connect in car with dual k-line
official vas5054 needs to add an adaptors vas6017 to be able to connect in this cars
GAL is an electronic switch for K1 and k2 lines
As I know all GAL has the same dump

What you exaclly want to try? To flash a clone with original dump?
Good luck

[heshamzn]

i have vcds 12 and was working good until i got error message sorry this function requires a lenience i don't know what is the atmega is it tool or program or where i can buy it is there any software can help ??

[pmcdiy]

i have vcds 12 and was working good until i got error message sorry this function requires a lenience i don't know what is the atmega is it tool or program or where i can buy it is there any software can help ??

I am with the same problema. My release is 12.12.0. Can someone help?

[mattydr67]

Guys without dumps this will cannot be fix it
Search and you find free dumps in the forum and reflash your tools
Otherwise will never work
Your tool is already erased. Unregistred
Or try to find a HQ clone and you never have a problems like this
But the HQ clone is 3-4 times expencive then a chinese clone but you can upgrade it as you upgrade a genuine one
Good luck

[presland11]

thanks for the help!

[mattydr67]

I didn't helped you.
I just advised you.
In the rest its your choise
Mr. Fantomel collection contain what you need dumps and software and how to flash your tool. Only that you need it more is an external AVR programmer
Good luck

[jollepe]

Guys without dumps this will cannot be fix it
Search and you find free dumps in the forum and reflash your tools
Otherwise will never work
Your tool is already erased. Unregistred
Or try to find a HQ clone and you never have a problems like this
But the HQ clone is 3-4 times expencive then a chinese clone but you can upgrade it as you upgrade a genuine one
Good luck


Where can I find a HQ clone?

[mattydr67]

There are two type of HQ clones
Both upgradable
1. One use cracked softwares and need to wait the seller to provide new software to be able to update
2. The other is using official softwares no cracked. In this case when a new software is released you can upgrade your tool
I have the second choise one that can be upgraded with officiale not cracked softwares when this one are released
I will not share any informations where you can purchase one of this HQ clones. Sorry!
Good luck

[elpaso544]

I have dump 15.7

[Raimon7]

I have a clone of VCDS made in Belarus and it is bricked after my friend tried to check his car. Originaly it was like vcds 12.12 with firmware v1.84. This cable is based on Atmega16. So can I flash it with vcds dump?

[alexm1]

Share some pictures to see what is under de plastic cover?

[Pornete]

I have this serial adapter : http://www.delock.de/produkte/G_61425/merkmale.html and my question is:
Can i make this serial adapter to work with any version of VCDS?
I need to make cable only for my car: VW Golf 5 2007

Thanks in advance

[alexm1]

Of course not

[rocdeng]

dear matty, I have a chinese VAG 10.6.4 and locked because un-mod software used. I've used the 1.92 flash, 232rl.ept and eeprom in 'VAG-COM MULTI STUFF.zip' and flashed them successfully. After I plug the cable in car, I got 'K2 short to ground' message, but the cable was functional. I've tried full auto-scan and clear error code, it worked fine.
So is the 'K2 message' a normal message when upgrade an old cable to new firmware?
My cable pictures are below.

404340404341404342

[liviudiaconu]

What version of VCDS used?

[morfej]

rocdeng ... it's not normal that you have K2 message. You are just lucky that K2 is not used so much on newer cars.

Might be GAL(ATF) that is not totally correct or one of the transistors used for K2.

br

[rocdeng]

Both 11.11.5 and 12.12.0 all the same message.

[rocdeng]

Maybe I broke some parts in reparing by mistake, and fortunately normal operations could be used :)
Somebody also told me maybe some transistors are broken.

[alexm1]

404395404396


Check first image to identify continuity path between obd2 pins and selected area in the second picture. You will find the bad T. Be carefully when solder out/in a new one...you could damage your pcb.

[rocdeng]

In the morning I found the first image on Ross-tech's website and identified the path of K2, and found it's totally disconnected... Maybe Chinese clone save it for cost. But I'm confused why it's all right when I was using the old firmware 1.84 + 10.6.4 ZHS software, maybe the firmware and software were all modified?

[alexm1]

In the end, it is a clone...and things like this could happen...
P.s.
I have same hardware as you and using 14.10.0 on it, no troublles at all...try reflash and see whats new.

[dijana31]

Hi!
Does anyone have dump for vcds 10.6.0 (eeprom 93c46)?
Thanks in advance!!! :D

[jakuza]

There are two type of HQ clones
Both upgradable
1. One use cracked softwares and need to wait the seller to provide new software to be able to update
2. The other is using official softwares no cracked. In this case when a new software is released you can upgrade your tool
I have the second choise one that can be upgraded with officiale not cracked softwares when this one are released
I will not share any informations where you can purchase one of this HQ clones. Sorry!
Good luck

If that HQ clones uses official softwares and upgrade that means when you do upgrade or activation of software it will send serial of that tool to RT servers. And when they check for it it will be blacklisted and unactivated - right? Or you must stay offline forever, but than you don't have upgrade.

Are you sure that upgrade will work?

[mattydr67]

Mate just for information
The serial its checked online everytime the computer is connected to the internet. That's right
But the serial its not blacklisted
You can use it online, you can upgrade it online and you can upgrade the firmware by USB and online
No need to stay offline forever
I'm using it only online because when i do diagnostic I check wiki.ross-tech for DTC or procedures
Good luck


P.S. - don;t ask me more because I will not talk about this and no other explanations - its better to know that all that will fly for free then sooner or later will be "killed" - so i like to keep it working

[Jay522]

So here is an interesting one...I bought a Chinese clone of a Porsche Durametric cable which was supposed to work with an old version of the Durametric software. It didn?t, so as I was considering buying a VAG-COM cable (VCDS works quite well with the Cayenne, just call it a Touareg) I realized my non-functional fake Durametirc cable was very similar, a FT232BM with I suppose some different code. So I ran an older version of VCDS (311.2), it recognized the cable and offered to flash it to firmware 1.87 (I believe). To my surprise it worked! I now had a VAG-COM cable working with 311.2 and it was reading codes successfully from the Cayenne.

Then of course I got too greedy and tried a newer version of VCDS (11.11 among others) and it offered to update the firmware to 1.92 ? and it did, and then the cable wouldn?t work with anything anymore! So I got MProg and loaded the .ept file for Ross-Tech that came with it (it identifies the device as a FT232BM) and now newer version recognize the device (11, 12 and 14 series) but says it is not connected to the car ? even when it is connected to the car.

So my question is can I get back to the old 1.87 firmware and at least have my old functionality back with the old VCDS software? I am a programmer and have worked with flashing firmware (but mostly phones) and I am not quite clear what VCDS is actually flashing when it updates the firmware. Is it loading code to the ATMEGA162? What MProg loads from the ept file seems too small to be code. I figure if VCDS can flash the cable I should be able to also do so without soldering an interface to the chip. My cable looks almost the same inside as rocdeng?s a few posts back, the number on the board is 23P2H1238A.

I know it is just a 20$ cable, but curious as to how this works, especially since it seems China is basically selling a VAG-COM cable as a Durametric with limited functionality.

Thanks!

[mattydr67]

To flash it back you need to flash the Atmega162
To flash it you need an external programmer and dumps ( flash+eeprom )
As you already know flash means bootloader+firmware
VCDS software is flashing by USB your Atmega162 firmware only ( the bootloader cannot be flashed by USB )
Ept files is for FTDI and it has nothing to do with Atemega162
I haven't fw1.87 but maybe someone else will help you
Good luck

[Jay522]

Thanks Matty, much appreciated. I guess I was assuming since VCDS can only update the firmware, the bootloader would not have been changed on the device. So how come there is no way to just deliver the firmware only to the Atmega162? I figured the firmware versions are the .bin files in the root directory of VCDS; I was going to try and reload one those from an old version of VCDS, maybe find 1.87 that way. Just curious why VCDS can do it and we can’t. Cheers.

[mattydr67]

Well bootloader is diffrent in clones then in newer genuine VCDS
But some has this new bootloader in the flash
But old bootloade in the flash is still ok in clones
I didn't said that its imposible or we cannot flash the firmware as well as VCDS software do it. I mean by USB
We can do it by USB too why not
Yes the firmware is in the VCDS software HP1xx.bin
So I advised you to use the public solutions because the other one are not public
Good luck

[Jay522]

OK, so I have been reading some more and this is making a little more sense to me. I didn't quite understand what you meant by a public solution versus a not public solution, but I think I do now. It is odd, considering many of these are counterfeit cables (!), but I will keep looking for the non-public way around this. All you would have to do is set the firmware on your cable to version 0.0, trigger VCDS to update, and then swap in any .bin file you want. Should be doable. Cheers!

[tajfun211]

Hi All,
I have problem with my tool, probably has been erased as there is FFFFFFFFFFFFFFF when I plug it in to USB slot.

Can You please advice if possible to fix it.
Below pictures:
https://s15.postimg.org/shjmq4j6j/IMG_3649.jpg (https://postimg.org/image/g2wupsro7/)adult photo sharing (https://postimage.org/)
https://s15.postimg.org/ydraowj4r/IMG_3651.jpg (https://postimg.org/image/7fxdn5yhj/)image hosting over 5mb (https://postimage.org/)
https://s16.postimg.org/obaepzx5x/fffffff.jpg (https://postimg.org/image/n9087gech/)free upload pictures (https://postimage.org/)

[vlad587]

Hi, how can I flash my atmega 162? Can I just use software and connect the cable via USB? I have Chinese VCDS 10.6.3 which stopped working, can you advise? Thanks

[alexm1]

Hi All,
I have problem with my tool, probably has been erased as there is FFFFFFFFFFFFFFF when I plug it in to USB slot.

Can You please advice if possible to fix it.
Below pictures:
https://s15.postimg.org/shjmq4j6j/IMG_3649.jpg (https://postimg.org/image/g2wupsro7/)adult photo sharing (https://postimage.org/)
https://s15.postimg.org/ydraowj4r/IMG_3651.jpg (https://postimg.org/image/7fxdn5yhj/)image hosting over 5mb (https://postimage.org/)
https://s16.postimg.org/obaepzx5x/fffffff.jpg (https://postimg.org/image/n9087gech/)free upload pictures (https://postimage.org/)
You have a good hardware, take a look "around"and find last free dump and using a AVR programmer diy a reflash.

Hi, how can I flash my atmega 162? Can I just use software and connect the cable via USB? I have Chinese VCDS 10.6.3 which stopped working, can you advise? Thanks
First show some pics with your pcb. You can not repair/update your cable via usb, it is necessary to solder 4 wires / using a programmer- in order to reflash atmega .