Chineese Galletto V54

[spiridonas]

Here the eeprom dump but after 3 times unlocked with fgtech v54.

[crackerx]

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=302994&stc=1any ideea to rep
air this old galetto.k-line not working

[teerak2uk]

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=302994&stc=1any ideea to rep
air this old galetto.k-line not working


Replace 2x smd resistor

Swap 2700 for 270 ohm

Swap 4700 for 470 ohm

Change HCF40106 for HEF40106BT

http://tapatalk.imageshack.com/v2/15/03/07/5cfb7680d646bb3126a864fee7ebb961.jpg

[crackerx]

i will try

[2200]

------------------------------------

[teerak2uk]

try this eeprom and report.
Think he has already got it done mate I saw a post from him to remove dpf

[morgano]

And what is the point changing those resistors? marked 4700 is already 470ohm and same for marked 2700 it is 270ohm. That monkey see monkey do solutions are only waste of time, risk pcb and relay integrity for nothing. Use logic and follow kline circuit to see what is faulty.


Regards,

[crackerx]

if someone want to help me, please help me but with tested ideeas not wrog translations from aliexpress idiot ideeas!
i must have there
270ohms and 470ohms to be OK and
HEF40106BT or HCF40106BT?

[morgano]

Good ic is hef


Regards,

[beti88]

Today I wanted to make an car with my fgtech v54 but got an error message.
I have reinstall it and fix the FTDI chip without any changes. Whats the problem?

The error message says: file corrupted, the application has manipulated and maybe its infected by a virus or cracked.

[kospoz]

Today I wanted to make an car with my fgtech v54 but got an error message.
I have reinstall it and fix the FTDI chip without any changes. Whats the problem?

The error message says: file corrupted, the application has manipulated and maybe its infected by a virus or cracked.
What other softwares you have with galletto?

[beti88]

What other softwares you have with galletto?

Probably eetool destoyed it, before I installed that it worked. Now I reinstalled Windows and it works now, I will try to install eetool and test.

[atomiczen]

v54 clone works on win7 32bit? i read everywhere that work only on xp

[gazvts]

Works on win 7 pro 64bit tried tested tricore ��

[teerak2uk]

v54 clone works on win7 32bit? i read everywhere that work only on xp
Works on both

[digi men]

windows 7 ultimate 32bit work ok

[crisgsm]

How try v54 on sirius 32?
in boot mode not read enything and obd only read 75% then error, but this time read ecu number!
please any advice?

Thank you!

[honingkoning]

change LV125A and HC125 with 74HCT125D, change the component to the left of LV125A with 74HC14D, change the component under the yellow rel? with 74HC14D, change LS14 with 74HC14D, change the two HCT645 with 74HC245D, change the two yellow rel? with G6AK234P-ST-US-5VC, change the little rel? with OMRON G5V-1 5DC

this mod can not transform your tool in the best tool but only in a better previous tool

maybe a stupid question but i could only find G6AK234P-ST-US-5VD, is this ok?
And how to upgrade from v53 to v54?

Wbr Adam.

[warrio67]

for relay its ok
G6AK234P-ST-US-5VD
5VC = 5V DC

[honingkoning]

for relay its ok
G6AK234P-ST-US-5VD
5VC = 5V DC
And how to upgrade to v54?

Wbr Adam.

[austingreen]

help me; with installation ( fgtech v54 ecutool chinese) http://i.imgur.com/eFbSXF6.jpg?1

It's normal, just click "ok" to proceed.

[hcsaibot]

I have a MED9.1 (2.0 TFSi) to flash other maps. Is writing over obd ok with v54 clone?

[morgano]

It's normal, just click "ok" to proceed.

No, not normal.

He needs usbfix the tool, and then set date to 01-01-13 to test again.

[Chippy0815]

for me it helps deinstall and after that reinstall....

[morgano]

Of course reinstall the fgtech edited may help. ;) But after make what i said before. Once you get the "Eseguire renewal bla bla ... " message the ftdi eeprom gets outdated, need usbfix it.

[fantomel]

Hi, i am new at this and a friend of mine made me a gift in this FGTech china. I wanted to ask for your expertise in what do i need to change in this interface as i am sure that china as always made a lot of mistakes or cut the costs. I have put HIGH resolution pictures of my interface HERE (https://mega.co.nz/#F!79tiXbYB!dfYidsUeyTqGRlAGAlQi8g) in details and i am attaching here one of the board complete.
P.S. I do not know if this is V53 or V54 since my friend did not give me the soft for it yet, but i think it's v53.

[Marmes]

Nothing wrong with that :)
Just need to change the relay for good quality ones. From omron

Hi, i am new at this and a friend of mine made me a gift in this FGTech china. I wanted to ask for your expertise in what do i need to change in this interface as i am sure that china as always made a lot of mistakes or cut the costs. I have put HIGH resolution pictures of my interface HERE (https://mega.co.nz/#F!79tiXbYB!dfYidsUeyTqGRlAGAlQi8g) in details and i am attaching here one of the board complete.
P.S. I do not know if this is V53 or V54 since my friend did not give me the soft for it yet, but i think it's v53.

[ovi730]

q20 is importamt, your transistors are relay bad , ls14 must be changed also

[Marmes]

And in this version you must be very carefull with polarity when connecting a psu, this version of galletto does not have protection.

[fantomel]

So, to be exact in this interface i must replace:
1 relay at (K3) are G5V-1 5DC
2 relays at (K1 & K2) are G6AK234P-ST-US-5DC


Q18 - ZVP2106A
Q20 - ZVN2106A - or equivalent ones 2N7000 or ZVN4206A


I replace LS14 with 47HC14D?
Do i need to replace other pieces like capacitors or i do not know?
Thanks for your expertise.

[hcsaibot]

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=301787&stc=1http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=301788&stc=1http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=301789&stc=1

In the last photo is my version that is working full :) after many many changes If you copy it is 110% that you will succeed. please use google to find coresponcences or ask direct on the forum

Thank you for your images :stung:

I made a picture from my V54 china clone. Red marked are mounted parts, yellow marked are parts i would like to replace.
capicators / Relais i will change in future.
Is the 2.2K resistor are needed?
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=306790&stc=1

[obnchip]

is there a repaired softer also?

[teerak2uk]

is there a repaired softer also?
Euro clone soft

[hcsaibot]

Will eu Clone soft work with China clone?

[teerak2uk]

Will eu Clone soft work with China clone?
Yes it does on a reworked china clone never tried it on one before rework

[obnchip]

anybody got a euro clone soft?

[Chippy0815]

anybody got a euro clone soft?

can get it here:
http://ul.to/2ann5mny

[beltronics]

can get it here:
http://ul.to/2ann5mny
That applies to any V54?

[teerak2uk]

Or here

https://www.dropbox.com/s/p4zfx7gyqce8ioo/AES_Universal_Flasher_v2_Novembar_2012.zip?dl=0

[lucim12]

hy, this is version from obdauto i just bought, and its the poorest quality clone Ive seen so far..
im wondering how they dindt use horseshoes insteed...
k-line read ok, relay cliks when trying to write, bdm read ok, write havent even tryed.. CAN no read...
here is a pic
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=306898&stc=1

[70max]

Or here

https://www.dropbox.com/s/p4zfx7gyqce8ioo/AES_Universal_Flasher_v2_Novembar_2012.zip?dl=0

Hi friend
EU clone software works well with China clone?

thanks for your response
best regards

[Chippy0815]

depends on your china clone......
with some clones will work, with some not.

[70max]

depends on your china clone......
with some clones will work, with some not.

Thanks for your answer
I'll try

[teerak2uk]

depends on your china clone......
with some clones will work, with some not.
I think it might be down to stability issues as mine never used to run with it but does now

[bersch8688]

Software work on my Chinese Galletto V54
My PCB is rework

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=306951&stc=1





http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=306954&stc=1

[hcsaibot]

With my China V54 it works too
Here is the loader, copy and replace it with the china loader.
The other files in china and eu are equal only loader ist different...

307029

[Chippy0815]

Not correct, not only Loader is different.

[Niaz]

Software work on my Chinese Galletto V54
My PCB is rework

Software work for me my pcb don't know rework or not :)

Can somebody face this problem in bosch ecu my tool connect only Int flash micro but not Ext flash ? Yesterday i put 5v & read good Ext flash but today want to write modified flash again it not connect to ext flash . 3v or 5v no connect now ! Any idea please ?

[mislav88]

why have you set voltage to 3.3?

just use good old bdm100, never failed me

[Niaz]

why have you set voltage to 3.3?
3v or 5v no connect now (connect Int flash micro but no connect Ext flash)! Any idea please ?
Not have bdm100. I was thought fgtech is better than bdm100 !

[honingkoning]

Software work on my Chinese Galletto V54
My PCB is rework

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=306951&stc=1





http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=306954&stc=1
What do you mean with re worked, you Just changed components like relay and the bad smd parts.

Wbr Adam.

[teerak2uk]

What do you mean with re worked, you Just changed components like relay and the bad smd parts.

Wbr Adam.
Yes.............

[fantomel]

I know for a fact that there is a fix for different tools serial. Tools with 0386 have it public while 0475 it's not. My clone it's v53 has sn 0475 and it's not working with this EU clone software.
Can anyone post the fix V54 for tool 0475?

[carmageddon]

v54 (0386) have only bad software and hardware, the one and only best software for 0475 are v53

[mysamed]

xp run problems fix and no data chang
tool-0475 for
http://dosyadepo.com/3oy

[fantomel]

v54 (0386) have only bad software and hardware, the one and only best software for 0475 are v53
Even so, does anyone have and it's willing to share 0475 fix for V54. I just want to play with it. I am really curious if i put the fix to v54 if eu clone software will work or not since now it's not working.

[carmageddon]

Even so, does anyone have and it's willing to share 0475 fix for V54. I just want to play with it. I am really curious if i put the fix to v54 if eu clone software will work or not since now it's not working.

you can not use fw 0386 with sw v53, o386 work only with (bad) sw v54

[lagas]

guys what is difference or how to know you have bad sw? i use v51, 53, v54 most no problem at all.

[fantomel]

Since already got out some pdf with changes, some pictures and so on on another forum, here is what i have gathered with help from friends to have a more proper hardware.
I have also made a little legend up to explain some stuff.

Keep in mind to use good components from companys like ST MICROELECTRONICS, NXP and OMRON and not some low ones.

http://i62.tinypic.com/fnuuc3.jpg

[ovi730]

thak you soom uch. your solution is working perfect

[carmageddon]

guys what is difference or how to know you have bad sw? i use v51, 53, v54 most no problem at all.

v50, v51, v52 = sw v48, no problem only if using upgraded hw.
v53 = sw and hardware bad for all china, v53 sw upgradable for no language, no data back, more stability but always with hw upgraded
v54 = sw and hardware very bad for all china, hw upgradable but sw no...i suggest hw upgrade and firmware downgrade to v53 for NO PROBLEM

[javyb]

v50, v51, v52 = sw v48, no problem only if using upgraded hw.
v53 = sw and hardware bad for all china, v53 sw upgradable for no language, no data back, more stability but always with hw upgraded
v54 = sw and hardware very bad for all china, hw upgradable but sw no...i suggest hw upgrade and firmware downgrade to v53 for NO PROBLEM
I'm currently running china v54 with component upgrade as recommended by you with AES euro clone software. AES v54 software bad too?

[gazvts]

Aes version far as i see no different to edited version bar the installer Both registered to the same user

[cosmind]

what is so bad with v54 china? read write edc17 audi, bmw, opel 1.3mjet, delphi dcm3.4, fiat mj8df, bdm work, crafter edc16 by obd, crafter edc17 bootmode...
only problem is driver, if you install other ftdi tool you need to install again fgtech

[carmageddon]

have bad development for solve data problem and have zero stability, i downgrade any v54 cpu to v53 and use clean software!

[teerak2uk]

have bad development for solve data problem and have zero stability, i downgrade any v54 cpu to v53 and use clean software!
Is it still capable to do pcr2.1 unlocking with downgrade

[youk]

have bad development for solve data problem and have zero stability, i downgrade any v54 cpu to v53 and use clean software!

can you send me the firmware V53 please ?
i have a j-link and ulink2

[carmageddon]

Is it still capable to do pcr2.1 unlocking with downgrade

v53 and v54 are the same software but v54 have bad mod for no data back and no language, very bad!

[heteromies]

v53 and v54 are the same software but v54 have bad mod for no data back and no language, very bad!

Please, what you try to say or prove? Is that common problem or just with crap hardware? You mean Software 53 is better cracked than 54? How it can seen in real life?!?

[Chippy0815]

You mean Software 53 is better cracked than 54?


v53 and v54 are the same software....

i think it isn't that difficult to understand?

[honingkoning]

Please, what you try to say or prove? Is that common problem or just with crap hardware? You mean Software 53 is better cracked than 54? How it can seen in real life?!?
Come are you serious? The guys is saying its better to buy v53 and make hw mod and work with v54 sw.
Thats it! V54 is bad quallity hw and sw.

Wbr Adam.

[gezame]

v53 and v54 are the same software but v54 have bad mod for no data back and no language, very bad!

Hi
friend, I think soft in V54 Chinese version (just like EU), is more ancient than software version V53.
I have a V53 Chinese with software 11-2012, and can read-write-unlock eeprom PCR2.1 for example.
Clones V54 (soft is dated 09-2015), one can unlock simos PCR2.1 not pujeden read write eeprom

[carmageddon]

@ gezame : hi, v54 have bad crack and no stability, really ****, this is!

@ heteromies : i test all my tools on ecu!

[honingkoning]

@ gezame : hi, v54 have bad crack and no stability, really ****, this is!

@ heteromies : i test all my tools on ecu!
So would you advice to use v53 hw with mod and v53 soft?
And where to find good v53 sw?
Wbr Adam.

[Dobermann]

Hi
friend, I think soft in V54 Chinese version (just like EU), is more ancient than software version V53.
I have a V53 Chinese with software 11-2012, and can read-write-unlock eeprom PCR2.1 for example.
Clones V54 (soft is dated 09-2015), one can unlock simos PCR2.1 not pujeden read write eeprom


This is really unbelivable! Why have galletto v54 EU not sw version 11/2012

I want have this too for my v54 eu

@carmageddon

Galletto 4 Chinese is the same sw like eu 54

I use it long time and for me it runs stable !! What is the exact problem with this sw 54 eu.

thanks Dobermann

[Chippy0815]

it's not about the software, ist about the hardware!
But he said already many times.

HW is not stable so you have to replace much more things as on the v53.

[carmageddon]

This is really unbelivable! Why have galletto v54 EU not sw version 11/2012

I want have this too for my v54 eu

@carmageddon

Galletto 4 Chinese is the same sw like eu 54

I use it long time and for me it runs stable !! What is the exact problem with this sw 54 eu.

thanks Dobermann

the only cracked fg sw are v48 and v53, stop...but v53 clean are more stable between v54 because who crack v54 for solve data problem did not do a good job...each time you start sw v54 the antivirus stop the operation even if i put it on exclusion...v53 dont have problem with data back, language or bad setup, or antivirus

[fantomel]

i really get it now, can you please post a good and not virused software v53 and v48? the ones i found on-line are all with virus or incomplete on documentation. i have managed to clean one in a vm and made a mix in documentation from v54 but i would really love to have clean versions and complete V53 and older if you have.

[Chippy0815]

but the one i postet here in forum doesn'T have any kind of virus and is working well?!?

[VesKo]

Hi . I want know if Galletto v53 or v54 can make Audi A4 2.5V6 tdi(AKN)150HP by obd or boot mod ??
Thanks.

[bartekbartek]

If in car edc15 with 29f sure.

[hcwc]

It's edc15v,with obd but some galletto have problem with this ecu's.

[VesKo]

Which one is recommended?

[bartekbartek]

V52 do this ecu with no problem, good v53, v54 too.

[honingkoning]

Could someone share a good v53 or v54 that runs without Chinese xp.

Wbr Adam.

[Chippy0815]

@adam...i already postet here....look some posts before.

[Niaz]

3v or 5v no connect now (connect Int flash micro but no connect Ext flash)! Any idea please ?
Not have bdm100. I was thought fgtech is better than bdm100 !
Hi, Now i purchase BDM100 same problem .

P.S. Only was one time i can able to connect with fgtech read & write & i have all backup. please help !

[honingkoning]

@adam...i already postet here....look some posts before.
I tried that but it always stops downloading within a couple of minuts.

I have it running with v53 but v54 never starts.
I tried on normal xp, Chinese xp.
Usb and date fax.

Tommorow ik Will try to download it again.

Wbr Adam.

[honingkoning]

Guys i cant get it better than this, i get the screen but i cant enter anything.
Cant select language this is v54 i already reinstalled,
http://tapatalk.imageshack.com/v2/15/04/07/fd220c2f4f205460a3854f33bb8e13a6.jpg
http://tapatalk.imageshack.com/v2/15/04/07/43c01878add28ea011784c3b65ca2583.jpg

Any idea.

Wbr Adam.

[teerak2uk]

Guys i cant get it better than this, i get the screen but i cant enter anything.
Cant select language this is v54 i already reinstalled,
http://tapatalk.imageshack.com/v2/15/04/07/fd220c2f4f205460a3854f33bb8e13a6.jpg
http://tapatalk.imageshack.com/v2/15/04/07/43c01878add28ea011784c3b65ca2583.jpg

Any idea.

Wbr Adam.
It's not seeing the interface correctly have you looked in device manager

What does it do when you install Chinese version galletto 1.0

[honingkoning]

Yes i can see it there, interface is working with v53.
Nog idea what to do now,
Could it be a driver issue?

Wbr Adam

[teerak2uk]

Yes i can see it there, interface is working with v53.
Nog idea what to do now,
Could it be a driver issue?

Wbr Adam
It might be the serial issue try to pm Carmageddon he will know mate

Or maybe fantomel I know he was trying the same thing

[honingkoning]

It might be the serial issue try to pm Carmageddon he will know mate
Dont want to stalkt him, but i give it a try.

Wbr Adam.

[morgano]

If interface works with V53 sw will not with V54 because of tool serial number.

[carmageddon]

yes, problem finally solved

[honingkoning]

yes, problem finally solved
Thanks for the great help carmageddon,
Great member Who is willing to give you some of his valuable time.

Thank you.

[Chippy0815]

and will you share solution with others too?
I think this will be helpful for other users too.
(I Think this is the sense of this forum) :)

[honingkoning]

and will you share solution with others too?
I think this will be helpful for other users too.
(I Think this is the sense of this forum) :)
I cant share any sollution,and there is no secret.
Carmageddon installed soft for me and it worked.
Conclusion i had bad soft or wrong installed.

Wbr Adam.

[heteromies]

I cant share any sollution,and there is no secret.
Carmageddon installed soft for me and it worked.
Conclusion i had bad soft or wrong installed.

Wbr Adam.

I think he use wrong version software. If tool is 0386 cannot use 0475 sofware?

[carmageddon]

i never said that i can do work 0386 with v53 or viceversa!


i always wrote that v53 clean with one mod at two dll can work perfect without problem, i wrote that software v54 are bad cracked and have no stability for this reason!




v53 work only with 0475 (the only best clone fg)
v54 work only with 0386 (****)

[Chippy0815]

my v54 works with 0475 without any problem.

[fantomel]

on another forum where i have posted the picture with modifications someone has made some adjustments. What do you think about them?
http://i59.tinypic.com/v5fjhx.jpg

[zecas]

hi
jus by replacing L9613 fore si9243 that someone knows what he is doing

regards

[ivofe]

Ok. So I think this is main question now. Is it possible to change(downgrade) firmware in v54 hw (386 tool) to v53 (475 tool) firmware ???

Many thx carmageddon.

[gonzagnr]

so finally i will take some time to try to make this galletto work
my pcb has the following components
U18: HEF4011BT
U21-U12: LM393
U10: A82C250
U16-U23: L9613 E9403
U20-U22: MAX485ESA+
U11-U15: 74HC245D
U8-U17: 74HCT125D
U14-U9-U19: 74HCT125D
U4: 1117cd-1480
U3: 1117cd-3.3-1418
q20 and q18 zpv 210 6a


i know q20 has to be ZVN
and the others???????????
will this work with eu software after rework, isnt it?

[Harrycz44]

Hi All
I have problem with my fgtech after connect to pc got error about "unknow devices" someone know what parts is bad? Thank you

[fantomel]

maybe you have fake ftdi, or ftdi it's gone and needs reprogramming

[Harrycz44]

I tried reprogramming with mprog but can not load ftdi drivers..

[heteromies]

I tried reprogramming with mprog but can not load ftdi drivers..

Remove tool from usb and install software again. Then connect tool and try mprog.....

[carmageddon]

so finally i will take some time to try to make this galletto work
my pcb has the following components
U18: HEF4011BT
U21-U12: LM393
U10: A82C250
U16-U23: L9613 E9403
U20-U22: MAX485ESA+
U11-U15: 74HC245D
U8-U17: 74HCT125D
U14-U9-U19: 74HCT125D
U4: 1117cd-1480
U3: 1117cd-3.3-1418
q20 and q18 zpv 210 6a


i know q20 has to be ZVN
and the others???????????
will this work with eu software after rework, isnt it?

u9-u14-u19 are NOT 74HCT125D!!!!!!!!!!!!!!!

[gonzagnr]

u9-u14-u19 are NOT 74HCT125D!!!!!!!!!!!!!!!
thank you for your reply.
can you tell me best replacement for those??
are the other ok??? (except for q20).
regards.

[bobolin4o]

Some pages above...
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=301787&d=1425041189

[gonzagnr]

Some pages above...
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=301787&d=1425041189

thanks, i have seen that image and others so i was not sure what was best solution.
i will try to transform my pcb into that hehe.
regards.

[javyb]

Anyone know what components are responsible for bdm as my bdm stopped working

[Chippy0815]

Anyone know what components are responsible for bdm as my bdm stopped working

as far as i know U9,U14,U19

[javyb]

Dies anyone know what the 8 leg eeprom on U6 is for abd does, as I ripped 1 track off pcb

Thanks

[morgano]

U6 is not an eeprom. It is DC to DC step up converter. So you probably ****ed one feeding line of the PCB.

This is exactly what i mean when i say that monkey see monkey do "repairs" put the pcb integrity in risk. Many times people without needed skills unsolder and solder unneded parts just because saw them in a list over the internet. Before exchange parts like crazy test if they are faulty and really need to be swapped. My friendly advice. ;)

[javyb]

U6 is not an eeprom. It is DC to DC step up converter. So you probably ****ed one feeding line of the PCB.

This is exactly what i mean when i say that monkey see monkey do "repairs" put the pcb integrity in risk. Many times people without needed skills unsolder and solder unneded parts just because saw them in a list over the internet. Before exchange parts like crazy test if they are faulty and really need to be swapped. My friendly advice. ;)
I don't think so the pad that came off has no connection on board hence it came off. I asked what U6 was for not for a lecture

[javyb]

2011 mercedes c220 cdi with delphi crd 3.xx ecu can v54 china read and write this ecu anyone tried thanks

[bugarcek]

2011 mercedes c220 cdi with delphi crd 3.xx ecu can v54 china read and write this ecu anyone tried thanks

I readed it and write without a problem.

[ivofe]

I did read w212 2.2 2015 crd 3.7 with no problem.

[carmageddon]

software v54 is not newer than v53, are the same software bad cracked, v53 are better!

[teerak2uk]

software v54 is not newer than v53, are the same software bad cracked, v53 are better!
Along as hw has the correct serial in it ?

[antwnhszr]

hello to all.i try to connect for read this ecu but i don't any luck......the ecu is from mini cooper s 1.6.L MED.17.4 with sak-tricore 1766 mcu.i try with 3 diferent's resistor on the boot 1.2Kohm , 1Kohm , 680ohm and 820Ohm..what make wrong?always i have message : ERROR BOOT. my device is from china from carsung,until now i don't have any problem's on other's ecu's today it's first time to try the tricore.....anyone guy know what must can i do now?any help?
regard's

[ddnc]

Hello

Can someone tell me what value those blue resistors, under U8, have and why they look like that? Burned??
My tool refuses to right edc16c39, after righting it many times successfully. It does not show message to turn of dash for 10 sec. and gives error changing speed when initializing.
It was updated (hd and sw) from V53 to V54 by "DK Veteran". After this problem, he just said to right it over BDM because this ECU is very problematic and never answered my questions again... maybe bad relays over PM box...

From what i have learned from this thread, my main problem is wrong U18 (k-line hex inverter).
But there is much more to replace like U11, U15, U20, U22, U21, U12, U2 and change all 6A transistors to 6B.
Do i need to change KL4 to D96?
My U14 is HC14A. Is it the same as 74HC14D?
Thanks
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=314864&stc=1

[javyb]

Middle one is 225 and next to that is 164. First one is a capacitor

[ddnc]

Thanks @javyb for your time. Already managed to solve my righting problem with edc16c39 over OBD. Beside starting with fresh XP OS, updated framework, C++, Java and with out antivirus and firewall, I think that my issue was poor quality usb cable because when wiggled, relays started clicking and led?s stopped blinking.

Will update my hw ass soon as possible but my doubt still stand about changing KL4 to D96 and if U14 HC14A necessary to replace by 74HC14D.

I would love to do it my self but don't have proper equipment.

PS: @morgano I know that you are not obligated to answer my questions but when I requested your service, you gave me all your attention. So I quote you that " monkey see monkey do..." doesn?t apply to you in terms off helping.

[morgano]

Mate the hw is working ok or not? Is not my bad if you used bad quality usb cable and or had problem with mixed drivers or whatever sw problem you had.

The unit as i sent to you was 100% working, true or false? I also answered your posts after near a year of sending you the repaired unit. Is very nice see you posting ~~~~ about me in the forum after all. Thanks. No more to say.


Regards,

[garagetech]

What do you think about this board

Good , bad or the ugly?

Thanks

315409

[toms4]

As usually China...
U2 ADAA not soldered,
at least 74HC14 at own place
component nr-s not printed

[garagetech]

As usually China...
U2 ADAA not soldered,
at least 74HC14 at own place
component nr-s not printed

Thanks pal can you explain u2 adaa location and nrs thanks

[teerak2uk]

Thanks pal can you explain u2 adaa location and nrs thanks

https://www.dropbox.com/s/ydafdzcal0esr9a/%5E4CAA83474068F85A0361420B1D469F0BBCAD84D4A241DFA D1F%5Epimgpsh_fullsize_distr.jpg?dl=0

All Respect to my very good friend Fantomel for his hard work

[raben785]

Hi all, I tell you ... I have a V54 galletto rework, the problem I have with it is the time to boot mode to edc17c10 Tricore psa does not work, tell me the soft to power cycle and others but always throwing boot mode error.
K Line, bdm ok.
Someone can tell me what the components are installed to run the boot mode in the Tricore ECU.
Thanks greetings.

[Multipla]

Can anyone help me? I would replace a part of bdm in galletto V53, Yesterday function very well and today not function, When i connecct in ecu edc16c8 surprised in Windows of galletto it appears ::: micro not recognized. What have happened? Pleace you can show me what pieces to change or at least I would like a confirmation of what I intuited. Please can you help?

[sbegnozz]

Hi all, but if we want to buy an europea version where we find it ?
Many thanks

If you cannot write link in there forum please send in pm email

[kristikapa]

hello to all.i try to connect for read this ecu but i don't any luck......the ecu is from mini cooper s 1.6.L MED.17.4 with sak-tricore 1766 mcu.i try with 3 diferent's resistor on the boot 1.2Kohm , 1Kohm , 680ohm and 820Ohm..what make wrong?always i have message : ERROR BOOT. my device is from china from carsung,until now i don't have any problem's on other's ecu's today it's first time to try the tricore.....anyone guy know what must can i do now?any help?
regard's

Mine is having the same problem. Managed to read it using kess...

[beti88]

Hi there

When i try to read my golf 5 -2009 through OBD it read to 40% then give me error. I dont have power supply to the laptop or the fgtech v54, do i need it? Or could it be that the fgtech is just crap?


This is my PCB, maybe its just ~~~~.
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=327716&stc=1http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=327717&stc=1

[spychu14]

Can I use ?

VP2106N3-G instead ZVP2106A
VN2106N3-G instead ZVN2106A

Original ZVP and ZVN are really difficult to find.

[maku1977]

my new galletto v4 china... arrived today334872

[CustomCars]

maku1977, looks ok, should be no problem with that one.
QC is passed :-D

[teerak2uk]

QC is passed pmsl sorry but don't mean nothing especially when coming out of china

[warrio67]

relay are omron it's good point

[teerak2uk]

relay are omron it's good point
Yes along as they're good one we changed them out on ours for ones from a reputable company like rs,farnells etc

[teamtuner]

seams to be 80% ok that china pcb

[cokeaddict]

Ok guys, i'm new here, so go easy please.

I am new to these fgtech things so I am a little confused.

Attached is a picture of my board, is it any good ?

It shows as tool-0386 when ran under windows 7 (with incorrect date), but is there any advantage (or disadvantage) to updating it to tool-0475 ?

Also is there any way to get it to working under Windows 10 Pro x64 (this seems to be the only software I can not get running under windows 10) ?

[gazvts]

I would change it to 0475 forget about windows 10 , your def on the right thread so not to be harsh here but read a little this thread you'll find which components to change & check if correct

[alinambro]

Hello. On my pcb i have this:
U14-U9-U19 32YLWBF LS14
U8-U17 74HCT125D
U11-U15 74HC245D
U20-U22 MAX485ESA
U16-U23 L9613
U10 82C250Y
U21-U12 LM393
U18 CD4011BM
2 relee OMRON G6AK-274P
1 relee HKE HRB1-S-DC5V
U2-ADAA
Can you tell me what is better to change? Thank you

[teerak2uk]

Hello. On my pcb i have this:
U14-U9-U19 32YLWBF LS14
U8-U17 74HCT125D
U11-U15 74HC245D
U20-U22 MAX485ESA
U16-U23 L9613
U10 82C250Y
U21-U12 LM393
U18 CD4011BM
2 relee OMRON G6AK-274P
1 relee HKE HRB1-S-DC5V
U2-ADAA
Can you tell me what is better to change? Thank you
Read the thread answers are there

[vasco fernandes]

I received my galleto 4 v54, this is the PCB:


http://i.imgur.com/E8xffOz.jpg?1


good or bad ?

[alinambro]

yes , i know but some pieces are compatible. i don`t know what to change. for example i have 2 OMRON G6AK-274P. i have to change one with OMRON G6AK-234P or no. some people say it`s with 2 OMRON G6AK-274P.

[gazvts]

omron g6ak-274p = good
relay HKE HRB!-S-DC5v = change to omron
U14,U9,U19 =change
Q20 & Q18 check an change if needed
U10 is ok for 12v change if you need 24v
check thread everything is here

[alinambro]

I understand. Thank you ;)

[maku1977]

does not work in bdm ... not on edc16, replaced the 3 LS14 with 74hc14d 2 diodes with NVZ / zvp2106a but always comes out this message! while with the v48 ebdmpro reads quietly. someone has a solution ???336789336790

[raben785]

Hello, I have a problem with my V54, Line Can not working.
Linea K ok.
Bdm ok.
Ok boot mode.
I've changed the a82c251, LPC2119 and still not working.
Can anyone help in this matter.
A greeting.

[carmageddon]

fg v53-54 dont use a82c251, here you have right components to use for it!

dont invent any other component and use this list!

U14-U9-U19 are 74HC14D nxp
U8-U17 are 74HCT125D nxp
U11-U15 are 74HC245D nxp
U20-U22 are MAX485ESA+
U16-U23 are E-L9637D
U10 are PCA82C250 nxp
U21-U12 are LM393
U18 are HEF4011BT nxp
Q18 are ZVP2106A
Q20 are ZVN2106A
big relais : G6AK-234P ST-US 5VDC
small relais : G5V-1 5VDC
Y1 change resonator with quartz 16 mhz
c21-c26-c28 100uF 50V
the other 7 capacitor are 10uF 50V

[raben785]

Thanks for answering.
My v54:
U14-U9-U19 are 74HC14D nxp---------ok
U8-U17 are 74HCT125D nxp-----------ok
U11-U15 are 74HC245D nxp-----------74HCT245D
U20-U22 are MAX485ESA+-------------OK
U16-U23 are E-L9637D---------------ST L9613
U10 are PCA82C250 nxp--------------PCA82C251
U21-U12 are LM393------------------OK
U18 are HEF4011BT nxp--------------OK
Q18 are ZVP2106A-------------------OK
Q20 are ZVN2106A-------------------OK
big relais : G6AK-234P ST-US 5VDC--OK
small relais : G5V-1 5VDC----------OK
Y1 change resonator with quartz 16 mhz--No change.
c21-c26-c28 100uF 50V--------------OK

the other 7 capacitor are 10uF 50V

My:
C20-C17-C14-C23 --- 10uf 50v. The rest is 100uf 50v
I know V54 with the same components as the mine and the CAN line works ok.
Anyway missing components will turn me on your list.
Thank you.

[javyb]

Hello, I have a problem with my V54, Line Can not working.
Linea K ok.
Bdm ok.
Ok boot mode.
I've changed the a82c251, LPC2119 and still not working.
Can anyone help in this matter.
A greeting.
Did your can work when u bought the galetto ir has it never worked from the start

[raben785]

Components will change nothing else come near China.

Photo:
337088

[carmageddon]

Thanks for answering.
My v54:
U14-U9-U19 are 74HC14D nxp---------ok
U8-U17 are 74HCT125D nxp-----------ok
U11-U15 are 74HC245D nxp-----------74HCT245D
U20-U22 are MAX485ESA+-------------OK
U16-U23 are E-L9637D---------------ST L9613
U10 are PCA82C250 nxp--------------PCA82C251
U21-U12 are LM393------------------OK
U18 are HEF4011BT nxp--------------OK
Q18 are ZVP2106A-------------------OK
Q20 are ZVN2106A-------------------OK
big relais : G6AK-234P ST-US 5VDC--OK
small relais : G5V-1 5VDC----------OK
Y1 change resonator with quartz 16 mhz--CHANGE WITH QUARTZ.
c21-c26-c28 100uF 50V--------------OK

the other 7 capacitor are 10uF 50V

My:
C20-C17-C14-C23 --- 10uf 50v. The rest is 100uf 50v
I know V54 with the same components as the mine and the CAN line works ok.
Anyway missing components will turn me on your list.
Thank you.

change the colored components

[raben785]

I change and see what happens ...
But ... 74hct245d is for BDM-JTAG function, and that works for me perfectly.
A82C251 A82C250 is for 24v and 12v. (The function is the same just change the voltage).
Can transceiver L9613 ST.
E-L9637D Driver peripheral OBD.
Resonator nothing to say, it may be defective.
Regarding the capacitors, the three closest to the LPC, you say 10uf 50 and mine are 100uf 50v, the change? or so it can work well.

[carmageddon]

I change and see what happens ...
But ... 74hct245d is for BDM-JTAG function, and that works for me perfectly.
A82C251 A82C250 is for 24v and 12v. (The function is the same just change the voltage).
Can transceiver L9613 ST.
E-L9637D Driver peripheral OBD.
Resonator nothing to say, it may be defective.
Regarding the capacitors, the three closest to the LPC, you say 10uf 50 and mine are 100uf 50v, the change? or so it can work well.

74HCT245D IS NOT RIGHT, NEED : 74HC245D, PCA82C250 AND E-L9637D, resonator make bad job (have you never heard resonator watch? no, only quartz watch)

I WROTE WHAT NEED TO DO ON THIS PCB FOR HAVE STABLE TOOL WITH BETTER PROJECT, obviously v54_0386 are only ~~~~ and bad cracked, the only right and last version are v53_0475 with right dll for no data back, no asian language more stability

but think what you want

[raben785]

I will change everything to see if the problem is fixed CAN line.
I would like to change the firmware and soft by the v53 but do not have it.
If someone is kind enough to send it to me or any link, I would appreciate.

[adrianvick]

My opinion:
74hct245d works just fine, don`t need to change it. I tried it on multiple clones, also others use it.
L9637D and L9613 is almost the same. Both of them OK. I have multiple EU clone, all of them with L9613.
So no need to change it to 9637d, only if you suspect that they are broken.
Ceramic resonator also works.

Also G5V-1 5VDC is not 100% correct. Correct component is G5V-1 6VDC

I have 2 or 3 clones, where something does not work, even after full pcb rework. And when I say full rework, I mean every component was changed, lpc, resistors, capacitors, ft232, and so on.
Problem is with the pcb, it`s rubbish...

[carmageddon]

i dont remember how many tools i test and mod and re-test for have better project, anyway, i dont wrote random this mod, its all tested and with SW mod work all perfect.

the 70% of problem on this tool is not HW but SW....bad cracked and without stability (and old for v54_0386)....on HW you can play how you need.

eu clone have ONLY pcb good, the rest are bad

[zecas]

hi

is the schematic for this tool v53/v54 available somewhere??

regards

[bartekbartek]

In wchich transistors i can replacement this Q18 and Q20. I see i can replace zvn2106a with this one ZVN4206A, but for ZVP2106A i cant find good part. Can someone help me?

[blackbird700]

I bought chinese v54, installed drivers, it boots up and shows 0386, but I can't read ECU from car (can - ford 1.6tdci, both 66 and 80 kW) via OBD.
I tried on two computers, with xp sp3 and 7 sp1, same result.

NOTE: I read entire thread before posting this and I am even more confused now XD

[queroseno]

[Quote = blackbird700; 2682669]. Compr? V54 chino, controladores instalados, se arranca y muestra 0386, pero no puede leer la ECU del coche (puede - 1.6tdci ford, ambos 66 y 80 kW) a trav?s de OBD
me prob? dos ordenadores con XP SP3 y 7 SP1, mismo resultado. NOTA: Le? tema entero antes de publicar esto y estoy a?n m?s confundido ahora XD [/ quote]


unmodified not read, change components and then try, I happened to me with a language partner, I galletto as coming from China not to or ID, you change the components and to ID, read and wrote by OBD
Cheers

[ionutdanica]

Hello guys this is my galletto v54 china is ok for read/write obd/bdm?<br><div>
http://s28.postimg.org/wr5fnwwvx/20160128_134208.jpg (http://postimg.org/image/ja8h51mk9/full/)
host image (http://postimage.org/index.php?lang=italian)

http://s22.postimg.org/bywk820c1/20160128_134153.jpg (http://postimg.org/image/m8yz7aq7h/full/)</div><div>url immagine (http://postimage.org/index.php?lang=italian)<br><br></div>

[rafalleku]

Hey. I have galletto v54 china i have big problem. communicate error seed key SK1.....no reading my computer and error error & comunicat log & please contact @@@......
what is the problem???? broken cable???? please help. Please see image my foto. screen programm.

[mircea13]

remove dash fuse. it's no. 11 in the pannel.

[rafalleku]

remove dash fuse. it's no. 11 in the pannel.


i don't have no 11.... what is problem galletto v54....?? seed key error??sk1????? please help....
i have audi a4 b6 1.9 tdi avf

[pulsar2000]

Any one have a decent V54 patched sw for china v54 ?
im fed up reinstalling every time i use the thing,

i hear v53 works more stable, any one please ?
pm if you can help,.
cheers

[Music73]

i don't have no 11.... what is problem galletto v54....?? seed key error??sk1????? please help....
i have audi a4 b6 1.9 tdi avf

I have a 04 AVF A4 B6 and had no problems reading or writing through OBD... could this been mapped before with a protected tuning file..

[bersch8688]

Hey. I have galletto v54 china i have big problem. communicate error seed key SK1.....no reading my computer and error error & comunicat log & please contact @@@......
what is the problem???? broken cable???? please help. Please see image my foto. screen programm.
http://www.digital-kaos.co.uk/forums/images/styles/DarkCore/misc/paperclip.png Attached Thumbnailshttp://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355028&stc=1&thumb=1&d=1454239898 (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355028&d=1454239898) http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355029&stc=1&thumb=1&d=1454239925 (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355029&d=1454239925) http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355030&stc=1&thumb=1&d=1454239948 (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355030&d=1454239948) http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355031&stc=1&thumb=1&d=1454239968 (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=355031&d=1454239968)


Use MPPS V13 ---> Work Perfect

[samigravano]

Hi,

Chinese v54 ok for me (read, write edc16c34)

[heteromies]

V54(0386) is poor cloned version. Firmware need downgrade to V53(0475), then can use newest(11/2012) soft which is also better cracked than V54 soft. If need more info howto, just send PM.

[cp2010]

SN 0386 and SN 0475 both is fw53 not 54 !
difference only one... 0386 use sw from 11/2012, 0475 use sw from 12/2012 (can read/write epp in pcr2.1 ecu)

[heteromies]

SN 0386 and SN 0475 both is fw53 not 54 !
difference only one... 0386 use sw from 11/2012, 0475 use sw from 12/2012 (can read/write epp in pcr2.1 ecu)

Yes, that i tried to say, 0475 is better and newer and everybody should use it.

[testune]

chinese version can read and write EDC16C34? Does anybody know if can do a Ford Focus diesel 2010?

[CustomCars]

chinese version can read and write EDC16C34? Does anybody know if can do a Ford Focus diesel 2010?

batch sure.

[jamesG60]

I'm trying to install FGTech v54 chinese clone on Windows 7 32bit and I keep having the same error.
Once installed I start Galletto and I am given a prompt saying 'Update available, update as soon as possible'. I click OK, the dialogue box disappears but the software never opens.

I have uninstalled and re-installed countless times. I originally tried installing on windows 10, got nowhere so rolled the laptop back to windows 7. I remember seeing the 'Registered to Dagon XP' dialogue the first time I opened the software on windows 10 but I've not seen it since.

The laptop I'm using is a 1Ghz A6 AMD 11.6" with 6gb ram and a 500gb hdd so I can't see system specs being a problem. There is nothing else installed on the laptop bar drivers and chrome. Windows defender is disabled, as is windows firewall and there is no AV installed.

If anyone has any ideas I'd really appreciate it.

Thanks
James

[electronistul21]

you read notepad with instructions?after instal,you need open software from EOBD2 exe!

[electronistul21]

yes is good clone! what SN you have?i think 0386.in this case you need make little rework in your PCB

[morphvale]

Hi Guys,

What do you think about 2N3904 instead of ZVN2106A and 2N3906 instead of ZVP2106A? They seem to have similar datasheets.
My board is using these, and I just can't find the ZVN and ZVP ones, and alternatives would be similar to the ones above.
If they're fine, I might end up changing just the relays, the oscilator and the LS14. But I've read the LS14 are just for BDM, which I'm not planning on using (I'll mostly work on my own Focus EDC16C34, and some friends Passat with EDC15P+ and A4 with EDC16C31).
Another question, what would be what is the 'normal' time to read/write an EDC16C34? I got about 30 minutes for reading, and about 15 minutes for writing (plus the extra that are required before starting the car, not to lose IMMO data and injector coding on Focus).

This is my board, also works with AES EU SW.

362237

[parik]

hi, does exist windows 10 usb drivers for china fgtech v54? thx

[gazvts]

windows 10 (updated from win 7) works but you shut pc down next startup stops working tested no point working perfect win 7 32bit

[electronistul21]

Hi Guys,

What do you think about 2N3904 instead of ZVN2106A and 2N3906 instead of ZVP2106A? They seem to have similar datasheets.
My board is using these, and I just can't find the ZVN and ZVP ones, and alternatives would be similar to the ones above.
If they're fine, I might end up changing just the relays, the oscilator and the LS14. But I've read the LS14 are just for BDM, which I'm not planning on using (I'll mostly work on my own Focus EDC16C34, and some friends Passat with EDC15P+ and A4 with EDC16C31).
Another question, what would be what is the 'normal' time to read/write an EDC16C34? I got about 30 minutes for reading, and about 15 minutes for writing (plus the extra that are required before starting the car, not to lose IMMO data and injector coding on Focus).

This is my board, also works with AES EU SW.

362237
datasheet not similar.2N3906 and 2N3904 ist bipolar tranzistor,ZPV and ZVN ist MOSFET transistor.when you change you can see your galletto work too fast.

[morphvale]

Oh, thanks, I completely missed that part.
Just managed to find the ZVN and ZVP ones eventually and ordered them as well. Now waiting for the all the parts together with the USB-TTL adapter to also try to update to 0475.

[vasco fernandes]

Hi Guys,

What do you think about 2N3904 instead of ZVN2106A and 2N3906 instead of ZVP2106A? They seem to have similar datasheets.
My board is using these, and I just can't find the ZVN and ZVP ones, and alternatives would be similar to the ones above.
If they're fine, I might end up changing just the relays, the oscilator and the LS14. But I've read the LS14 are just for BDM, which I'm not planning on using (I'll mostly work on my own Focus EDC16C34, and some friends Passat with EDC15P+ and A4 with EDC16C31).
Another question, what would be what is the 'normal' time to read/write an EDC16C34? I got about 30 minutes for reading, and about 15 minutes for writing (plus the extra that are required before starting the car, not to lose IMMO data and injector coding on Focus).

This is my board, also works with AES EU SW.

I have this galletto, work fine

EDC15, EDC16 OBD/BDM and MED17 OBD/Tricore

[morphvale]

I've also done EDC16C34 OBD with it (a bit too slow if you ask me). I'm still considering on replacing the relays and the transistor, and upgrading to 0475 once my USB-TTL adapter arrives. The software for that seems to run fine under Win 10, both 64 and 32 bits. I can start it fine right now, but it won't detect the tool as it 0376.

Sent from my Nexus 5 using Tapatalk

[vasco fernandes]

you read edc16c34 by can or k-line ?

[morphvale]

Is there a way to switch between the two? I just chose ford-focus-edc16c34.

Sent from my Nexus 5 using Tapatalk

[parik]

windows 10 (updated from win 7) works but you shut pc down next startup stops working tested no point working perfect win 7 32bit
and clear usb drivers for windows 10?

[electronistul21]

Is there a way to switch between the two? I just chose ford-focus-edc16c34.

Sent from my Nexus 5 using Tapatalk
what you wish make?switch from 0376 to 0475?No way!

[morphvale]

Actually that should work, just search for Fantomel's posts. What I meants was switchinh between can and k-line, in regards to vasco fernandes question.

LE: This is the result. BTW, running on Windows 10 64bit, which is the real reason why I tried to achieve this anyway. Electronistul, fellow RO here, just drop me off an email if you need any info.

362719

[electronistul21]

ok!good job! you try in to car? work fain?

[morphvale]

No, not yet. I'm waiting for the transistors to arrive today, and after I replace those together with the relays (already did the oscillator before the firmware upgrade) I'll test it.
I'm still a bit reluctant about the LS14 to HC14 conversion though, as I don't have a hot air station, and I wouldn't risk using the cheap 30W/70W soldering iron that I have.
This weekend I'll probably give it a go at reading two of my friends cars, a 2004 Passat with EDC15P and a 2005 Audi with EDC16U31 (I think). We'll see how that goes.

LE: Ok, so I've replaced the ZVN and ZVP transistors and also all the 10uF condensers. Didn't do the relays yet, as I could not desolder them completely to remove yet. Went to the car and did a read. That took about 20 minutes. About 4-5 minutes less than before, but I still believe it's pretty much. Not sure though how much it should be for a Ford with EDC16C34 though, so maybe that's normal.

[B19hly]

which version is mine?
362981362982362983

[skywoker]

V 50 (51) . Older one !!

[carmageddon]

fg v48 original copy

[B19hly]

V 50 (51) . Older one !!

Thanks for the update ,

do you know how to get this workin by any chance?

[skywoker]

@carmageddon user could explain to you better.

[cawadany]

Thanks for the update ,

do you know how to get this workin by any chance?
What's the problem?

[carmageddon]

@carmageddon user could explain to you better.

left fg v48 genuine, right fg v48 clone mod by me

http://s9.postimg.org/yvxnhwiiz/fg_v48.jpg (http://postimg.org/image/yvxnhwiiz/)

[B19hly]

What's the problem?

I bought the tool I while ago and I have requested the key from the supplier with no joy ? I sent them my HW id as the read me says , I then requested a key from this site and was sent one but the eobd.exe won't open , also my fgtech has driver on the disk which doesn't work ? I can give some one team viewer access if they don't mind helping me.

Thanks for the reply

[mircea13]

hy guys. i have this chinesse fg v54 tool nr 0386 . i'm currently using the AES software. can i use this the read and write edc16c31 from e60 525 bmw and edc16c35 from bmw e90 320d over obd? 363357

[B19hly]

I managed to get hold of the supplier on getting this working , sent me a key and a name but the usb driver wouldn't go on my laptop , so I formatted it and got the driver to install but now my HW id has changed again , I got hold of a Keygen but there must be a different one for my tool as I didn't have to mess with the date or time last time tool worked, I put my hardware id into it to see if it gave me same key from the supplier and they was different.

[bobolin4o]

I managed to get hold of the supplier on getting this working , sent me a key and a name but the usb driver wouldn't go on my laptop , so I formatted it and got the driver to install but now my HW id has changed again , I got hold of a Keygen but there must be a different one for my tool as I didn't have to mess with the date or time last time tool worked, I put my hardware id into it to see if it gave me same key from the supplier and they was different.

Mate, there is a patched software to work with old Galletto... http://dox.bg/files/dw?a=7d253ae254
Fyrst of all, right mous klick on the archive, properties, hit "unblock", ok.
Extract the folder to C:/
Plug the interface and if need drivers, use the drivers from "fgtech_new_driver"
If the program don't start (with plugged and feeded interface), use "eep_rep"...
Regards!

[B19hly]

Will this work for mine ? Can you help

[B19hly]

Just looked at the files ? Mine doesn't use a dongle ? Is this for the older ones ?

[electronistul21]

I think yes.is old software for V48 and V50 .

[B19hly]

Mines a 51

[carmageddon]

fg 49-50-51-52 are ALWAYS v48!

[B19hly]

Any of you ok to help me later on ? I have team viewer , the supplier said my windows 7 won't work , so formatted and put xp same thing , eobd failed to open

[electronistul21]

not can help with teamwiever for instalation.when net ist conection,software ask for update.

[morphvale]

ok!good job! you try in to car? work fain?

Just as an update, I have since replaced all parts, besides the LS14. I won't be planning on updating those anytime soon, as I do not have a hot air station, neither do I plan on using BDM, as the tool is just for personal use.
I have since also flashed the car twice, without issues.
Reading time on Ford Focus EDC16C34 is about 20-21 minute, while writing time is about 11 minutes. I still consider this quite slow (I've had DPF Off done on my car some years ago,and both reading and writing were less than 10 minutes, but that was with a genuine New Genius tool), but maybe it is normal.
I would like to thank the forum, for all the free quality information that you can find. As a hobbyist enthusiast, this is quite valuable!

[bobolin4o]

not can help with teamwiever for instalation.when net ist conection,software ask for update.

Absolutely NONSENSE!
On all my machines, the network is ALWAYS connected!
Best regards!

[morgano]

Absolutely NONSENSE!
On all my machines, the network is ALWAYS connected!
Best regards!

Bobo is completely right. No matter if internet is on or off regarding fgtech clone.

[electronistul21]

when install fgtech with internet conection open,you receive mesage ,,your hardware need upgrading",and sofware not open.i talk about galletto 2 V4 ,chinese,sn 0386.

[morphvale]

You can just click ok, and nothing will happen. Works with 0386 chinese and aes sw.

Sent from my Nexus 5 using Tapatalk

[mircea13]

can i use this v54 to write on ne364428wer bmw's like e 60 or e90 over obd ?

[teamtuner]

can i use this v54 to write on ne364428wer bmw's like e 60 or e90 over obd ?
why not?....yes you can...only edc15 and edc16 by obd

[mircea13]

and is it safe? i'm using the AES software with this fgtech v54 clone. what i don't know wich is safer this v54 clone, kess v2.10 fw 3.009 chinesse clone or mpps v13?

[gazvts]

check other posts by carmageddon (http://www.digital-kaos.co.uk/forums/member.php/150846-carmageddon) for rework your fgtech

[mircea13]

i've readed all of them. but instead of the ls14 everything seems to be ok on this pcb that i have.

[carmageddon]

-resonator need to be changed with quartz 16 MHZ
-change ls14 with 74HC14D NXP
-change little relais with G5V-1 5DC
-change U18 with HEF 4011BT NXP
-change L9613 with E-L9637D

[teamtuner]

ufff...and if not work,buy EU clone:stung:

[kospoz]

-resonator need to be changed with quartz 16 MHZ
-change ls14 with 74HC14D NXP
-change little relais with G5V-1 5DC
-change U18 with HEF 4011BT NXP
-change L9613 with E-L9637D

Why must change l9613 what is for ?maybe for canbus?

[bobolin4o]

Why must change l9613 what is for ?maybe for canbus?

It is for K-line, mate... and the chip, suggested by carmageddon is with better parameters...

[thayer201]

morning people,

i have a delphi ecu CRD2.30 OM651


can galletto v54 read and write good? or not supported?
also does anyone have jtag pinouts for it aswell please.

[honingkoning]

morning people,

i have a delphi ecu CRD2.30 OM651


can galletto v54 read and write good? or not supported?
also does anyone have jtag pinouts for it aswell please.

I did it with v53 takes almost 30 min, so keep the Car on a charger and the laptop also [emoji1].

Wbr Adam.

[thayer201]

I did it with v53 takes almost 30 min, so keep the Car on a charger and the laptop also [emoji1].

Wbr Adam.

thank you

im having to bench read/write this ? any guides ?

[honingkoning]

thank you

im having to bench read/write this ? any guides ?

I did it in the Car through obd socket

[electronistul21]

when change resonator with quartz not need put and 2 capacitors in according with tehnic specification?I not see this capacitors nowhere.

[morphvale]

Maybe it depends on the version you have? This one has it on the left side of the resonator: http://postimg.org/image/r0u5a9ojh/full/

[carmageddon]

-SN65HVD251/82C251 are not right (PCA82C250 is perfect).
vcc pin on this two components the voltage are ALWAYS 4,5-5,5 v, the differential voltage anyone see for c251 (24v) is not working voltage on car, is voltage possible present on can line!
the differential voltage allowable during exchange data on can for this tool with PCA82C250 are 26v (tested on cars 12v or truck 24v).
have a wider bandwidth for this value does not allow to do job on 24v...the problem is not 82C250 because is perfect.

-74HCT245 are not right (74HC245D is right)

-capacitor 4,7 uF 35v are not right (10uF 50V is right)

[morphvale]

Indeed you are correct, but I've only added the image in regards to electronistul21 question about the two capacitors near the resonator, not the other components, and should not be taken as an example for other components.

[mircea13]

so it's needed or not to change the capacitor near the quartz ?

[Matttes]

Hello all,
I have bad chinesse copy V54. OBD work well, but when I try write back data to EDC 16U1 via BDM, data was wrtie about few rows down.
Now I have order small parts writes by Carmagedon.
And work in downgrade to V53 and change Sn from 0386 to 0475. Change SN when I rewrite data in MCU?
I need full functions of this hardware.
Many thanks for answer.
BR and have a nice weekend.
Matias

[morphvale]

so it's needed or not to change the capacitor near the quartz ?

Only if you do not have the capacitors on the board, which seems to be the case for electronistul21. If you already have them, then why change them?

[dadal]

v54 (0386) have only bad software and hardware, the one and only best software for 0475 are v53

would you like to check my PCB please ? need I to change some parts ? cristal smd capacitor?
thank you

[electronistul21]

you have V54 sn0386.change LS14.ist good transistor ZVN and ZVP.after change LS14 ,try this configuration.

[dadal]

you have V54 sn0386.change LS14.ist good transistor ZVN and ZVP.after change LS14 ,try this configuration.
thanks I need then not too much parts , just transistor,,,I have this time good luck with an china clone
thanks mate

[vasco fernandes]

thanks I need then not too much parts , just transistor,,,I have this time good luck with an china clone
thanks mate

This are correct parts

U14-U9-U19 are 74HC14D nxp
U8-U17 are 74HCT125D nxp
U11-U15 are 74HC245D nxp
U20-U22 are MAX485ESA+
U16-U23 are E-L9637D
U10 are PCA82C250 nxp
U21-U12 are LM393
U18 are HEF4011BT nxp
Q18 are ZVP2106A
Q20 are ZVN2106A
big relais : G6AK-234P ST-US 5VDC
small relais : G5V-1 5VDC
Y1 change resonator with quartz 16 mhz
c21-c26-c28 100uF 50V
the other 7 capacitor are 10uF 50V

[dadal]

then it is almost done,,,I need just transistor :bebored:

thanks mate

[tango]

i have same hardware and it needs ls14 changing and the 2 transistors
also not sure on the caps as pics show 100uf in middle yet the pic from fantomel showing what to change shows 4.7uf and another shows 10uf so not sure to which they should be 10 or 4.7uf

[electronistul21]

change with 10 uf.not ist critical value.

[minimex]

Hi friends,
I ask, and here,
can someone confirm the action with MPC55xx
in ECU Volvo/Renault E5, TRW. My reading process up to 90% and stops.

With MPC5xx is ok

Thanks

[cp2010]

yes, all old clone can't read the ecu
try with ktag