X-Prog M

[avengervln]

Hi all

I need atmega dump Xprog-M.
Please help....
My Xprog only write device is client

Thanks
Check correct device port in environment options.
Press the update button, if window with authorisations shown, then firmware is ok. I think..

Check connection to chip. by the way, what chip you are trying to program?

[card2diag]

Hi, i bought x prom from China, it works well, i give that guy email to you, ( link removed)
(http://www.ufodiag.com/AD900+key+prog-hot/) (http://www.ufodiag.com/AD900+key+prog-hot/)
Maybe he can help you
hey,your guy mean xprog 5.0?

[adikk]

Connect Xprog M to EDC16 BDM
Hi! May be You know how connect Xprog-M to Delphi ECU by BDM?

[obdmaster]

heres picture of my clone xprog-m with BDM interface virginising 307 BSI, big thanks to umoussa, for helping me with virgin dump. thanks m8.


clone xprog-m read verified, program, verified first time. these are a very good tool.

[baikas2004]

i boot fron chaina x prog m works ok no problems

[canorivera]

heres picture of my clone xprog-m with BDM interface virginising 307 BSI, big thanks to umoussa, for helping me with virgin dump. thanks m8.


clone xprog-m read verified, program, verified first time. these are a very good tool.

Hi my friend I just received my Clone XProg-m yestarday and I already activated it with software v5.0, but I don't know how to use it i want to learn how to use, is there any possibility that you can send me an exercise to do, I mean in case you have one, or some information about it, I have manual but I need a practical guide :).....

Thanks in advance...:barscarf:

[baikas2004]

CHAINA XPROG M WORKING 100%

[PremierD]

One and only Friendly warning !!!!!!!!!!!
Anne1986 (http://www.digital-kaos.co.uk/forums/members/202196-anne1986/)

[clive_pather]

the chinese only know how to sell the goods, when asked how it works they say must speak to engineer(who knows nothing) they r very good at copying but thats about it.

[canorivera]

the chinese only know how to sell the goods, when asked how it works they say must speak to engineer(who knows nothing) they r very good at copying but thats about it.

Yes we shouldn't never expect any support from chinese sellers, once we pay it's a totally different attention.

[zedbull]

After update to v5,0 Mircronas work OK.
Tested on passat 2007 dash

[napel]

Works on all micronas, when is showing garbage, then use another car with same mask mates.

COAX CABLE MUST BE MAX 12CM and all cable connections must be 100% OK, then you never get Error message.

[cqae]

I just got my xprog clone too & couldnt get it to work, ended up being the usb cable that was supplied with the unit, every time I plugged it into my laptp all of my usb ports actually shut down & wont come back unitl I restart, maybe a short inside the cable.
but used a spare & all updated & authorisations are working

[Aniskey]

Hi can i have soft v5.0 for xprog m clone to update mine
is v4.5
thnx

[cqae]

do some searching & you can see there are quite a few guys that have updated theirs to v.5 successfully. even some youtube vids that will show you how.
I just pressed the update button on mine and viola!

[snecii]

Hello!

Please help me to read out dump from Megane UCH in my there is 4L91N chip

How to do it with Xprog?
I can not find any like that in xprog!

I got a help with upa usb, but I think itis not the same as Xprog:

http://www.digital-kaos.co.uk/forums/f175/4l91n-renault-megane-161555/

Somebody? Really thanks for help!

[T72]

Hello!

Please help me to read out dump from Megane UCH in my there is 4L91N chip

How to do it with Xprog?
I can not find any like that in xprog!

I got a help with upa usb, but I think itis not the same as Xprog:

http://www.digital-kaos.co.uk/forums/f175/4l91n-renault-megane-161555/

Somebody? Really thanks for help!

it is the same for xprg to, must use 9s12 adapter,
+5v
GND
RESET
BKGD


regards

[paffendorfbg]

ive just ordered clone xprog-m, its the same as the cheaper one from autosky, but far better price:
China ECU Tools Centre (http://www.ecutool.com/productshow.asp?ID=1923)


Im a beginner, but the price was just toooooo good. Will let you know how i get on!!!!!!!!!!!!!!!!:beheaded:

hi mate
are you happy with it ?

[kautuvera]

hi
I need help with Xprog and FREECALE 68hc908az60
0L72A

can you help me the X-PROG how to win or do I connect my wires ?

regard

[puiu]

hi
I need help with Xprog and FREECALE 68hc908az60
0L72A

can you help me the X-PROG how to win or do I connect my wires ?

regard
This MCU is secured ,to read in circuit you need this:
$F3-$B1-$F3-$AB-$F3-$A5-$F3-$9F
( but can be another SS...)
and look in X-prog manual page 17
i think you have to read like MC68HC08AZ32
i allways use ETL, is the best for secured 908
regards
Puiu

[pawlenko]

hex for atmega64 xprog-m v5.0 all authorizations, fusebit config.


exchange or sale

[puiu]

hex for atmega64 xprog-m v5.0 all authorizations, fusebit config.


exchange or sale

Here is a sharing or give for free Forum !
NO EXCHANGE OR SALE

regards

Puiu

[kautuvera]

hi,

I read the IC have been difficult for friends who can help me?
MC68HC05E6 mask(0F28B)
can you help me the X-PROG how to win or do I connect my wires ?

Regard's

[teerak2uk]

i think you need to use adaptor with this

[puiu]

hi,

I read the IC have been difficult for friends who can help me?
MC68HC05E6 mask(0F28B)
can you help me the X-PROG how to win or do I connect my wires ?

Regard's

Hi,

just lift all pin you need to connect,
less GND and VDD ,

regards

Puiu

[kautuvera]

Hi,

just lift all pin you need to connect,
less GND and VDD ,

regards

Puiu


I act according to you, but I still did not result:hmmmm2:

You can put a photo?

[puiu]

Look in attachment,
regards

Puiu

[kautuvera]

Please see the pictures, it is not true?

[einet]

Hi,
I have 1 question, i bay xprog from "sinosells" in the back side off the xprog have "xprog 4.5 full" but i bay a full version 5.
May question is how have the version 5 that confirm my infos on the pichture.

einet

[puiu]

Please see the pictures, it is not true?
Hi,
if you lift all the pins from PCB,
the only problem can be that you forgot to change
in programmer Option - Environment - Device
the value of Oscilator , X-Prog put this value for 2MHz osc
by default for this MCU
and you have there 4MHz so change this value to 4000000
and try again :)
regards
Puiu

[puiu]

Hi,
I have 1 question, i bay xprog from "sinosells" in the back side off the xprog have "xprog 4.5 full" but i bay a full version 5.
May question is how have the version 5 that confirm my infos on the pichture.

einet

You have ver. 5

regards

Puiu

[kautuvera]

Hi,
if you lift all the pins from PCB,
the only problem can be that you forgot to change
in programmer Option - Environment - Device
the value of Oscilator , X-Prog put this value for 2MHz osc
by default for this MCU
and you have there 4MHz so change this value to 4000000
and try again :)
regards
Puiu


So now what way?:flybye:

[tehnosoftex]

I think you must buy upa usb. I have also xprogm but not use much for hc05. It is a good tool but has its limits. I think that for esl and key with hc05 the tool for the job is upa usb. It is a must have on every automotive technician toolkit.

[puiu]

So now what way?:flybye:

I have no other tips sorry,
maybe your clone is not so god
i read with my X-prog original
exactly the same MCU from an ESL,
10 min ago just to test
if is working,and is reading perfectly,
maybe is better to buy UPA-USB original
as my god friend Sorin (tehnosoftex) recomended,
regards

Puiu

[kautuvera]

My (PB0) pin basic IC circuit to connect and I could read about it, Thank You Friends

[JotaB]

So now what way?:flybye:
Hi if you are reading in circuit you must put same value of oscilator in the enviroment of XPROG-M as the value that is on the board where you are connecting

[peppery]

hi
i have xprog v.5.0
i can read, but cant erase 35080
i use adapter but no succses
any advice???

[z786]

if its v6 or vp then you cannot erase it mate

[Zmann]

hi
i have xprog v.5.0
i can read, but cant erase 35080
i use adapter but no succses
any advice???

Xprog-m does not support erasing the incremental register of 35080 v6 and 35080 vp no matter with or without the adapter, but only 35080 3 and 35080 6. Don't know what your chip is.

[snecii]

it is the same for xprg to, must use 9s12 adapter,
+5v
GND
RESET
BKGD


regards


Witch one is 9s12 adapter?
How to use it can you share pictures?

Thanks!

[snecii]

I have to read out PIN code from megane 2.
I have Xprog and I have some picture where to connect witch cable.
Can I use HC<S>12 BDM Adapter with cables?
Can somebody help to read it out with xprog? I need only the dump file, I have Zedbull to read pin code!

Thanks

[snecii]

Wich device do I have to choose? MC9S12DT256 MASK 4L91N

It stops at bypass security...... and nothing

[peppery]

Xprog-m does not support erasing the incremental register of 35080 v6 and 35080 vp no matter with or without the adapter, but only 35080 3 and 35080 6. Don't know what your chip is.


my chip is 35080 3 and i cant erase???

[snecii]

somebody????? Please a little help!


Thanks

[avengervln]

Wich device do I have to choose? MC9S12DT256 MASK 4L91N

It stops at bypass security...... and nothing

I had this problem when connections were bad. Also when MC was burnt.

[teerak2uk]

my chip is 35080 3 and i cant erase???
post dump here and someone will erase it for you

also what vehicle is the dump from

[Zmann]

post dump here and someone will erase it for you

also what vehicle is the dump from

I think he has a probem with erasing the used 35080 chip with his Xprog, not the dump.

[teerak2uk]

if still on pcb then try to erase of the pcb

[ecutoool]

Xprog no erase new generation for 35080V6 you need exchange ne eeprom

[butonu]

Hi, i have an xprogm vers 5.0 and now i think bdm adaptor is broken.Last week i read 9s12 without problems with this adapter and now when i try to read i have error: Bootloader initialising error.Can't to acces BDM.Check BDM conections.
All conections is ok , all curents is ok , i think proc from bdm adapter (lattice) is problem.Have you the contents of this proc? If i use xprogm with another device i can read write ok, for example hc908, or another device who works without BDM adapter.

Thanks

[tachonow]

Hi, i have an xprogm vers 5.0 and now i think bdm adaptor is broken.Last week i read 9s12 without problems with this adapter and now when i try to read i have error: Bootloader initialising error.Can't to acces BDM.Check BDM conections.
All conections is ok , all curents is ok , i think proc from bdm adapter (lattice) is problem.Have you the contents of this proc? If i use xprogm with another device i can read write ok, for example hc908, or another device who works without BDM adapter.

Thanks
Be happy that you didnt corrupt flash data from a cas or ezs.
Ive told not to play with this clones on 9s12 mcus.

[ristici]

update with sw 26.04.2010 is still working, tested today on xprog-m in plastic case

i want to know whether your programme work with secured 9s12 mcu's

best regards

[dbilik]

i want to know whether your programme work with secured 9s12 mcu's

best regards
yes it work...

[Min2xx]

can anybody show real pictures connecting xprog-m to ews? i need to see the connection diagram. i don't what is wrong with my device. thank you
My X-progm ( serial 326, from ECU factory) not work with EWS-3 (mask D46J). I disconnected MODB line, and connect shortly, when initializing device. All work Ok. I must do it all times, when reading, verifying, recording data. How I can resolve this?:banghead:
P.S. Connection diagram in attachment

[cqae]

they plug that connect xprog & has the wires going out to the mcu didnt come with my clone, did you guys get it or did you get one made up seperately?

[ivanxxx]

they plug that connect xprog & has the wires going out to the mcu didnt come with my clone, did you guys get it or did you get one made up seperately?

You have to make them yourself. You get wires for bdm adapter with xprog, but not the main ones.

[napel]

My X-progm ( serial 326, from ECU factory) not work with EWS-3 (mask D46J). I disconnected MODB line, and connect shortly, when initializing device. All work Ok. I must do it all times, when reading, verifying, recording data. How I can resolve this?:banghead:
P.S. Connection diagram in attachment

always connect the MOD.B when do D46J


BUT NEVER CONNECT MOD.B WHEN DO 2D47J OTHERWISE LOOSE DATA, NEVER NEVER NEVER

ONLY CONNECT PLUG TO SOCKET

[teerak2uk]

My X-progm ( serial 326, from ECU factory) not work with EWS-3 (mask D46J). I disconnected MODB line, and connect shortly, when initializing device. All work Ok. I must do it all times, when reading, verifying, recording data. How I can resolve this?:banghead:
P.S. Connection diagram in attachment


Not sure but maybe because you are using windows vista/7.

Only a guess but i mostly use xp for things like this

[Min2xx]

Not sure but maybe because you are using windows vista/7.

Only a guess but i mostly use xp for things like this
Yes,
I use this on win7, reading on board Motorolla, epromm, all works good.
Ok, I will test it on xp today

[Min2xx]

Not sure but maybe because you are using windows vista/7.

Only a guess but i mostly use xp for things like this
In XP the same problem :( More solutions ? :giveup:

[marassa]

hey geys im just a bay x prog m clone whin i tray to work in RENAULT KANGOO with motorola MCU 68HC908AZ32A it see divice is silonce time eror

[marassa]

it see device is silent.timeout error

[taihei]

I had Fiesta 2009 1.4 need to adjust...using xprog clone not successed to read 9s12hz256..device is silent so i stop and power up dash at a bench...now the mileage is showing blank ...is it possible mcu eeprom data corrupted when perform read device? Sharing please....

[stefaudio]

put dash to car on bench lcd its empti

[taihei]

put dash to car on bench lcd its empti

Happy to hear about that, hope mcu is still ok...btw i can't put on car..just got it from other state cust.
Need to know what programmer you used for 9s12hz256 & where you bought it from.
I'm just another :eating: from mr wang-ecutool.

[calin_bm]

use upa usb programmer,it works fine for that

[card2diag]

HALLO***65292;UPA USB SERIAL PROG AND XPROM***65292;WHICH IS BETTER***65311;
( link removed)
(http://www.ufodiag.com/AD900+key+prog-hot/) (http://www.ufodiag.com/AD900+key+prog-hot/)
help me to choose.
thanks

[papalos_]

Hi mates.

Do you what IC are placed on xprog board insted of LM317?

Regards.

[pepiktdi]

Hi mates.

Do you what IC are placed on xprog board insted of LM317?

Regards. L317 LC 2X

[papalos_]

L317 LC 2X

Do you have any picture of the board mate?

Regards

[pepiktdi]

Do you have any picture of the board mate?

Regards
No picture

[taihei]

Hi mates.

Do you what IC are placed on xprog board insted of LM317?

Regards.


Blue Mainboard look it's same as what i had..for that component i got a lm317 but not DIP, it's LP package.
In the direction from DIP socket to 5V regulator:
The Connection of each LM317 is (Output-Input-Adjust) lead to positive 47 Uf cap.

[papalos_]

Take a care look on the pictures.

The blue PCB is mine xprog with LP package
The green is another PCB of xprog with D package.

According the pins of two packages there is a discordance!

What is your opinion about that?

[taihei]

Take a care look on the pictures.

The blue PCB is mine xprog with LP package
The green is another PCB of xprog with D package.

According the pins of two packages there is a discordance!

What is your opinion about that?

Another xprog varians...hmmm anyone can confirmed which one is working and WHERE to buy ? Mine is V5.0 from ecutool, it can't run on V5.0 Software, the error " Windows can't access the specified device, path or file.." i had tried to reinstall it many time,turn off AVG(Win32/ Themida detected), Change USB cable, try at com port....still got a same error.

But on V 4.5 Software it can run and show me all authorized at Hardware Info.

I think no need to be confused by xprog mainboard varians.
Stick to the purposed of a pair of 317, one is supplying VCC and the other VPP.
You can observe by yourself, Input came out from Mosfet near 5v reg, and Adjust is controlled by Atmega, that is what i know.

[papalos_]

With LP package, there are pins on board that are not used.

If I want to solder a D package instead of LP package, whats about the orientation of IC on board?

As you can see, the pins are different.

[Zmann]

With LP package, there are pins on board that are not used.

If I want to solder a D package instead of LP package, whats about the orientation of IC on board?

As you can see, the pins are different.

NOT POSSIBLE TO PUT D PACKAGE ON THE BLUE PCB! If there was not another blue, the blue pcb from ecutool has a totally wrong footprint for D package no matter how you orientate them. That why they put the LP packages in on the D package footprint. If both the blue and the green are yours you can check it out for the footprint differnce.

[einet]

Hi,
I have a ECUTOOLS xprog-m 5v, but in the moment the programmer don?t work i tray all, resolder verify all components "resistance transistors and capacitors ,..."
But the interface give all the time "Divice silince"
exist any dump or how i can confir that the atmega are working?

einet

[papalos_]

I start this discuss because my xprog(blue PCB, I don't have green) can't write on HC05 mcu family, but I can read them.

With other MCU I've try, It works perfectly.

I thought that the problem is on that point.

Who knows...

Here there is a picture of Xprog with green PCB. According the top layer, I can't find any difference except packages.

[card2diag]

HALLO***65292;UPA USB SERIAL PROG AND XPROM***65292;WHICH IS BETTER***65311;
( link removed)
(http://www.ufodiag.com/AD900+key+prog-hot/) (http://www.ufodiag.com/AD900+key+prog-hot/)
help me to choose.
thanks

blue pcb board is good working ?

[Zmann]

I s
Here there is a picture of Xprog with green PCB. According the top layer, I can't find any difference except packages.

Your answer is in your post #574 photo1 & 3. At least it should be found that the the output pin of LP package is not connected to the centered four pads (D package output). The running copper line differences are underneath.

But, how did you find the Xprog not writing the chip. Is it like this (http://www.digital-kaos.co.uk/forums/f172/how-read-micro-mc68hc05b16-116577/index2.html)

If you need some check on HW power supplying, the ic in the red circle is dual p channel mosfet performing as supply switchs to 2xLM317. One for 12v another one should be 17v found on pin5,6(7,8) and 7,8(5,6). These voltages are found only when the programmer is operating otherwise the mosfet is broken. My case, mosfet/2 for the 17v channel was broken.

[papalos_]

Your answer is in your post #574 photo1 & 3. At least it should be found that the the output pin of LP package is not connected to the centered four pads (D package output). The running copper line differences are underneath.

But, how did you find the Xprog not writing the chip. Is it like this (http://www.digital-kaos.co.uk/forums/f172/how-read-micro-mc68hc05b16-116577/index2.html)

If you need some check on HW power supplying, the ic in the red circle is dual p channel mosfet performing as supply switchs to 2xLM317. One for 12v another one should be 17v found on pin5,6(7,8) and 7,8(5,6). These voltages are found only when the programmer is operating otherwise the mosfet is broken. My case, mosfet/2 for the 17v channel was broken.

I've try the tip you describe here (http://www.digital-kaos.co.uk/forums/f172/how-read-micro-mc68hc05b16-116577/index2.html#post632477), without success.

I've read on MC68HC05X32 datrasheet, that for programming it needs 15V on VPP6 pin. I measured all the voltages on specific xprog-m adapter with 0d69j and I didn't find any 15V. Only 5V and 8,7V.

Did you replace the mosfet and everything is OK now? Can you program 0D69J now?

[teerak2uk]

silly question but did you have a 15v psu plugged into the xprog

[papalos_]

silly question but did you have a 15v psu plugged into the xprog

I've try all possible combinations!

The 9V voltage comes on relative pins with USB power supply also. There are circuits that increase the voltage in xprog.

[teerak2uk]

I've try all possible combinations!

The 9V voltage comes on relative pins with USB power supply also. There are circuits that increase the voltage in xprog.


yes but from what i know it is important that you have 15v power supply connected when you need good steady voltage hence why i always have my psu always plugged in then there should be no risk of voltage dip

[taihei]

@ Elnet

Once I tried to remove 32 Mhz xtall , and then run the software, under hardware info it can show me all info and authorization, that xtall is clocking lattice only, so i think this is the way to know atmega is working or not. What software version you used ? please post the info/datasheet for smd transistor, mine is using code A4W, IE , SN / 5N , A4 & 2A.

@ Papalos

It is from linear technology mine is mark 636 beside the main cap, dc dc converter it can boost usb 5 to 12v but it can’t draw more than 500ma, Teerak is right….you need external psu connected.

[papalos_]

If you need some check on HW power supplying, the ic in the red circle is dual p channel mosfet performing as supply switchs to 2xLM317. One for 12v another one should be 17v found on pin5,6(7,8) and 7,8(5,6). These voltages are found only when the programmer is operating otherwise the mosfet is broken. My case, mosfet/2 for the 17v channel was broken.

I check the voltage on pins 5,6,7,8. It's 12,27V and 17,76V.

What the hell is up here???

I can't write damn MC68HC05...

[maciupiciu]

I recive from ecutool a 5.0 version, blue PCB, but this time I get a bad one. I can read/write !2C and MW eeprom but i must repeat action few times untill job it's done, Silent Device message are display all the time. For me is just for testing , but i'm imagine how disappointed are other people.
:ridinghorse:
I think a half of mosfet area IC are broken , I replaced it with IC from 4.5 V good one, without succes. Now the voltages are good but i can't read any HC05 mcu (x32, B32). I don't try it on others mcu yet.

[einet]

Good Work!

What smd transistor you speek?.
I tray to bekome the authorization info window but the programmer only Silent Device message came, i tray to read with usb rs232 external power version 4.5 & 5 from ECUTOOLS but nothing!
Can i read the atmega over UPA or is this protect? or somone have the clone dump?
What i can make more?

einet

I

[Zmann]

I've try the tip you describe here (http://www.digital-kaos.co.uk/forums/f172/how-read-micro-mc68hc05b16-116577/index2.html#post632477), without success.

I've read on MC68HC05X32 datrasheet, that for programming it needs 15V on VPP6 pin. I measured all the voltages on specific xprog-m adapter with 0d69j and I didn't find any 15V. Only 5V and 8,7V.

Did you replace the mosfet and everything is OK now? Can you program 0D69J now?

I check the voltage on pins 5,6,7,8. It's 12,27V and 17,76V.
What the hell is up here???
I can't write damn MC68HC05...

What exactly the mcu are you playing with, HC705 or HC05? and on SEC. bypass board?, which one 1-002-0004 or 1-002-0005?

[taihei]

@ Einet

Of course smd transistor used at xprog blue pcb , maybe I?m wrong, i recall you said.. had check/verify all the res,cap,transistor. I think it?s hard for that atmega dump it's locked, like 9s12 had x-gate.


@ Papalos

You got that Blue PCB..that is working for almost mcu except HC05..and the other like Einet, Maciu and me with the same blue pcb,, just got "DEVICE SILENT". Please tell us where you bought that.

[papalos_]

I must say that I have no experience
What exactly the mcu are you playing with, HC705 or HC05? and on SEC. bypass board?, which one 1-002-0004 or 1-002-0005?
What the message does show when not writing

MC68HC05X32 mask 0D69J or 1H52A with programming adapter 1-002-0005. I choose white file
, security bypass is done and when it starts to write i got error message "write error", Continue?Yes-Yes All-no.

When I choose yes, the error appears again. When I choose yes all, it hangs and remain at the last percentage.

[Zmann]

Try again with Vpp1 pin is left off the 0005 adapter or if the programming process has done writing the adresss $00 to FFh the MCU now is already unsecured, remove it from the 0005 adapter and continue programming it without the bypass adapter.

[papalos_]

Try again with Vpp1 pin is left off the 0005 adapter or if the programming process has done writing the adresss $00 to FFh the MCU now is already unsecured, remove it from the 0005 adapter and continue programming it without the bypass adapter.

I'm a little confused.

You say to:

a. Try programming with Vpp1 lift
b. Then try programming in circuit?

[cammy25]

Hey guys... where is this DPD_V50setup_2010-05-16.rar ???
cant find it anywhere

[Zmann]

I'm a little confused.

You say to:

a. Try programming with Vpp1 lift
b. Then try programming in circuit?

If you can read it and found that $00 = FFh the MCU is unsecured, it can now be programmed in circuit. If not sure, try with Vpp1 left on the 0005 adapter

[papalos_]

If you can read it and found that $00 = FFh the MCU is unsecured, it can now be programmed in circuit. If not sure, try with Vpp1 left on the 0005 adapter

Thank you mate! :congrats:

Your method works!!!

Steps:

1. Read MCU & save the dump
2. Lift Vpp1 pin, select file you want to write, press write
3. And the end of writing process and before start security bypass, connect back(with a cable) the vpp1 back or untick write+verify in write mode

[milanoffracing]

Hey guys... where is this DPD_V50setup_2010-05-16.rar ???
cant find it anywhere

Hi Cammy, here is the link to DPD_V50setup_2010-05-16: http://rapidshare.com/files/427385736/Xprog-M_V5.0_16.05.2010.rar

[mymurat]

China ECU Tools Centre (http://www.ecutool.com/productshow.asp?id=1753&sortsid=&sorts=) %100 work

[einet]

My xprog work for 1 week! from ECUtools!!!!

[cammy25]

thank you milanof:champions:

[JotaB]

I've try the tip you describe here (http://www.digital-kaos.co.uk/forums/f172/how-read-micro-mc68hc05b16-116577/index2.html#post632477), without success.

I've read on MC68HC05X32 datrasheet, that for programming it needs 15V on VPP6 pin. I measured all the voltages on specific xprog-m adapter with 0d69j and I didn't find any 15V. Only 5V and 8,7V.

Did you replace the mosfet and everything is OK now? Can you program 0D69J now?

Hi
The need to connect the VPP6 is only for you to program the EPROM not the EEPROM same for the cane pin

[JotaB]

MC68HC05X32 mask 0D69J or 1H52A with programming adapter 1-002-0005. I choose white file
, security bypass is done and when it starts to write i got error message "write error", Continue?Yes-Yes All-no.

When I choose yes, the error appears again. When I choose yes all, it hangs and remain at the last percentage.

Don't use that adapter it's not correct. I've tryed it and in the adapter VPPr is conected and the 705X32 doesn?t need it. I've used a QFP64 adapter and made the conections one by one with the use of a 8Mhz oscilator conected in adapter, but the writing errors still appear, but could verify it at least two times ok, but don't verify it after write verify it with the comand verify later.

[UOBD2]

i can not use xprog-m to read hc05 chips and TMS370 chips,anyone know what i should pay attention to?or it is the machine problem?please help!

[teerak2uk]

i can not use xprog-m to read hc05 chips and TMS370 chips,anyone know what i should pay attention to?or it is the machine problem?please help!


look in device manager and see what port setting is

i.e. com3, com12 etc etc

[mexanico1971]

only work good in com 1,2,3 !
baud rate 215000 !

[teerak2uk]

only work good in com 1,2,3 !
baud rate 215000 !

not quite true as mine will run in 3 and 7 but i think if it is higher than com10 then you will have problems

[v-diag]

not quite true as mine will run in 3 and 7 but i think if it is higher than com10 then you will have problems


got the xprog m version 5 from ufodiag.

works fine have tested it too read a mercedes key module 9s12 chip secured.

read both the eprom and flash fine.

i think it has the blue circuitboard inside?

[nzlockie]

i have blue circuit board xprog-m. it WAS working fine but now when I try to read chips it says "vpp pin overloaded". How can I fix this?

It comes up with the same error no matter what chip I try to read.

[Zmann]

Presume USB is used, do connecting DC12V and not connecting give the same "vpp pin overloaded"?

[nzlockie]

Thanks Zmann - yes that gives the same result.

[Zmann]

Maybe some more people including me experienced with this problem with the blue board. I found two possible HW points which could generate the problem and if you'd like to do checking yourself.

IRF7316 full or partial broken (photos in this thread, post #581), put volt meter to pin 7,8 and GND then hit 'read' button (no device). You will get 17-18v shortly only when the programmer is running then halt. If voltage is present all the time this IRF7316/2 is broken. It's good to do the same too to pin 5,6 and the result should be the same but 12v.

LT1072 switching regulator degraded (photo in post #590, soic 8 pins), run help> hardware info...(no device). At this point the programmer should still work fine because this checking command uses less current. As a small 8 pin EEPROM use less current to perform reading (better 93Cxx), try to read it throgh the 8 pin socket and see what happen. Further checking needs to totally remove the board and put it upside down to check for the voltage on the bottom side.

When 'vpp pin overoladed' come up, did it give a gentle audible oscilated noise in the box?

[nzlockie]

Definately no audible noise whatsoever coming from the box.
When I run hardware info, it communicates just fine. I get a response telling me I am authorised for everything.

Tried reading a ST 24C08 through 8 pin socket and it generates the same error. VPP overloaded.

Tested voltage on the pins you mentioned and it performs just like you said it would. It jumps up to 17-18v for a brief second on 7,8 and 11-12 on 5,6. The voltage drops away as soon as the error message comes up. (which is pretty much straight away.)

Thanks again!

[nzlockie]

OK!
All fixed. Thanks to Zmann, I found one of the capacitors was rated too low. It had died and was a dead short. Replaced it with one rated for the correct voltage and problem solved!

Here is a shot identifing the guilty party. This guy is rated for 16v but as Zmann has pointed out, it will be getting spikes of up 18v.
I have replaced it with one rated for 25v.

Hope this helps someone else, because I imagine ALL the blue board X-progs are like this. Certainly all the ones in pictures posted in THIS thread are.

[Zmann]

Exactly the same problem point as one post before. This is the only line on the board that handled that highest volatge, 17-18 volts, no where else. The capacitor should have the voltage rate to tolerate this potential. The original 16v 4.7uF is crazy. I got a spare in stock and changed mine to 35v but 25v should be fine, only one to this position.

[szogun0]

OK!
All fixed. Thanks to Zmann, I found one of the capacitors was rated too low. It had died and was a dead short. Replaced it with one rated for the correct voltage and problem solved!

Here is a shot identifing the guilty party. This guy is rated for 16v but as Zmann has pointed out, it will be getting spikes of up 18v.
I have replaced it with one rated for 25v.

Hope this helps someone else, because I imagine ALL the blue board X-progs are like this. Certainly all the ones in pictures posted in THIS thread are.
I have X-prog with green mainboard and there is 50v 4.7uF capacitor.

[EduardNN]

I XPROG-M (China) now and then hangs: (
In eeprom ft232bl only FF.
Does anyone have the firmware eeprom FTDI (93S46)?

[elektro128]

eeprom 93S46 is empty.
FF value is correct

[Zmann]

The EEPROM is only for FT232BL power management. If the device is absent or the data is invalid FT232BL will use its built-in default values. In variants of the clone there are both emply eeprom as all FF or some with data programmed.

[astrofil]

Hello everybody. I`m trying to get the right Xprog-M I`m looking at http://www.ecutool.com/productshow.asp?id=2057&sortsid=&sorts= I assume it comes with all the adapters.I`m asking because I don`t see it at the picture. I don`t get why the one with soft ver. 4.5 is more expensive than the one with ver. 5.0. unless the more expensive comes with adapters and the other one without.

[EduardNN]

Hello everybody. I`m trying to get the right Xprog-M I`m looking at China ECU Tools Centre (http://www.ecutool.com/productshow.asp?id=2057&sortsid=&sorts=) I assume it comes with all the adapters.I`m asking because I don`t see it at the picture. I don`t get why the one with soft ver. 4.5 is more expensive than the one with ver. 5.0. unless the more expensive comes with adapters and the other one without.
Many Chinese do not know what trade and therefore do not know the real price ...

[Dmythross]

My xprog m is working ok,updated from 4.5 to 5.0 without problem;lately i noticed that previous to read it not saying "bypass security"and it usualy said every time when reading processors.In help i have all authorizations,so i have 2 questions:for you when you read hc08 secured for exemple is automatically calculate security secquence or you manualy enter it,second,is posibile to downgrade firmware and than upgrade again?Thanks.

[Dmythross]

After all it seems to be ok,is not as perfect as i tought this xprog m,but i bealive is a great tool to have.

[grinovsky]

my clone Xprog-M V5.0 work parfectly
i have a 68HC05B16 from peugeot 206 BSI that UPA can't read,ETL can't read,but when i put it in xprog-m he read it easely and programmed it as i like

[grinovsky]

and here is the launch of the software

[xandaschurras]

Buy a X-Prog Clone (China) but it gives me a mistake " Device is silent " and I do not have any authorization. This one OK the X-Prog?

Someone can help me, please.

Thank you very much

Regards

[Metin]

data in mcu damage or have firmware from old version and you must make update programmer

regards
metin

[xandaschurras]

data in mcu damage or have firmware from old version and you must make update programmer

regards
metin

This my X-Prog, It has an ugly, but like that color they me sent it today.

Regards

[Metin]

if you have active "Update Firmware" button,
then you have older firmware for this version software

regards
metin

[xandaschurras]

if you have active "Update Firmware" button,
then you have older firmware for this version software

regards
metin

Good ultimately the whole Ok, I gave him to update and I get up-to-date and already I have all the authorizations, thank you very much Metin.

A greeting

[obdmaster]

Been using my clone xprog-m via USB , for around 12 months on few devices it gave write errors, but after re-writing always finished succesfully. This morning thought id try it on rs232 serial port, on tms370 now using rs232 lead instead of USB and using 12v external power supply, writes near enough perfectly every time.

So far tested on tms370, which was the worst for write errors, and my 2 clone xprog-m,s (blue pcb from ecutool).


Just thought id share my experience with you guys and will hopefully help someone.

[teerak2uk]

prob more stable as it will be writing slower i use an old lappy with xp as i find it often better to use the com port rather than a usb to rs232 converter

[obdmaster]

prob more stable as it will be writing slower i use an old lappy with xp as i find it often better to use the com port rather than a usb to rs232 converter

It also seems faster at reading and writing

[teerak2uk]

It also seems faster at reading and writing

Strange as you would expect usb to be quicker

[obdmaster]

Strange as you would expect usb to be quicker


Might be m8, because my IBM T30 one of the computers i use xprog-m on is USB 1.0 m8 and by rs232 its quicker:eek:

[teerak2uk]

Might be m8, because my IBM T30 one of the computers i use xprog-m on is USB 1.0 m8 and by rs232 its quicker:eek:

LOL yeah i have the same with me old Tecra 2070 but might upgrade it to a new M10 these are well specced running vista which i dont need so will downgrade it to xp but even though its upto date i was surprised to see it has a serial port

[addgsm]

am having problem reading hc05p3 mcu from mazda 323 immo with xprog m i have connected cable like in the manual
but cant read
what pin do i have to left up ?
br

[dreadu]

is it possible to read old bmw ews2 or e36 ews3 with other plug? has anybody done it?

[baltazar3]

I was received a XPROGm 5.0 from http://www.ecutool.com (http://www.ecutool.com/)about week ago.When I first try to read some MCU ...XPROG blow up.
475C tantal capacitors is blow up.I find some mess in soldering tranzistor LM317.
Im properly connected 12V DC adapter and RS232 cable.Cheking hardware pass OK before that.
Im pretty shure that this device was not tested.
I will try fix them but need some help.
When I swap the capacitor and try again LM2904,B0505s and cap 220 are overheat.
XPROG is dead.No comunication with him.I will replace LM2904 but dont know what is chip 721 1072.Pin 1 and 8 are 0 Ohm.
Is that OK ?

[MOBILTRONIC]

Hi,mates.Maybe is usefull,...Dont buying X prog-M with blue pcb.On a few devices that I have had problems they were all with blue pcb.The main problem, as I have seen,is writing HC05 MCU.Reading is ok but writing all the time have errors.I have X prog-M with green pcb and all functions is OK!!!

[cosmind]

hello, please tell us how can we distinguish them without open

[xito]

I have XPROG 4.5 M with Atmega64 damaged how can I read and copy the ATMEGA64?

Thanks to all

[teerak2uk]

hello, please tell us how can we distinguish them without open


basically you can`t

[astrofil]

Any specific supplier who sells with green board ?



Hi,mates.Maybe is usefull,...Dont buying X prog-M with blue pcb.On a few devices that I have had problems they were all with blue pcb.The main problem, as I have seen,is writing HC05 MCU.Reading is ok but writing all the time have errors.I have X prog-M with green pcb and all functions is OK!!!

[efekhs]

Hi all
Can i read dashboard Octavia A5 2009 with xprog-m v4.5 ?

[MOBILTRONIC]

Any specific supplier who sells with green board ?I could not say,because I always buy from www.autokmfactory.com (http://www.autokmfactory.com) and one came X prog-M with metal housing and second time with plastic housing.I must say that we no longer sent in a plastic housing.

[Timppasa]

Any specific supplier who sells with green board ?

I bought this: XPROG-M X PROG M 5.0 With 18 Adapters Build 2010.04.26 - eBay (item 280584593283 end time Dec-04-10 02:43:21 PST) (http://cgi.ebay.com/ebaymotors/XPROG-M-X-PROG-M-5-0-With-18-Adapters-Build-2010-04-26_W0QQcmdZViewItemQQ_trkparmsZalgoQ3dLVIQ26ituQ3d UCIQ26otnQ3d2Q26poQ3dLVIQ26psQ3d63Q26clkidQ3d53710 80463547021012QQ_trksidZp5197Q2em7QQcategoryZ43989 QQitemZ280584593283)

In the picture there is only blue pcb's, but when I opened the package, every pcb was green. Also the housing is aluminium and inside is a green pcb.

I have been able to test it only once because my computers usb isn't supplying enough power, I think I must buy a power source for the XProg. When I tried it worked as it should and it showed full authorizations.

According the Ebay this seller has 95 of these still available, if they are all the same batch then maybe they are all with green pcbs.:hmmmm2:

[tech_cz]

To Bram380
Hi could you please upload again: xprog-m version 5.0 (2010-04-26) (http://rapidshare.com/users/EXEXDR)

WBR, Marek

[astrofil]

You can get it here from this seller . Right below the picture is the download link.
XPROG-m V5.0 Full Authorization_Programmer_Programmer and Chips_Auto ECU Tools_obd2, auto scan tool, auto ecu, auto scanners, key programmer (http://www.sinosells.com/goods-1132-XPROG-m+V50+Full+Authorization.html)

[bram380]

To Bram380
Hi could you please upload again: xprog-m version 5.0 (2010-04-26) (http://rapidshare.com/users/EXEXDR)

WBR, Marek


Xprog-m v4.5 to v5.0 (http://rapidshare.com/users/EXEXDR/0)

pass:
digitalkaos

[tech_cz]

Thanks, but I was looking for file 16,932,819 bytes long.
I do not know if I can use file 3515040-DPD_V50setup.exe 16,879,571 bytes long?

WBR, Marek

P.S. For Bram380: You does not have it there.
There are just videos :x-prog_clone_update_2010-05-12.rar, XPROG-m_clone_full_authorization.rar and XPROG-m_Clone_v4.5_to_v5.0.wmv

[gadroulll]

i just bought xprog-m 4.5 from ecu tool ,it works with software 5.0 , i would like to ask you if its working .i can see that it has all authorisations , its true?

why i can not programs memories like 29f400 with this tools ?

do you know any better programmer for all functions?

thanks to all

[bram380]

this version 5.0 from tmt (http://www.tmt.lt)

x-prog m not support eeprom 29xxxx

Use universal eprom programmer such as SmartPRO (http://www.programtec.com), Xeltek (http://www.xeltek.com), Wellon (http://www.digital-kaos.co.uk/forums/www.weilei.com/VP-990e.htm), Hi-Low (http://www.hilosystems.com), TOP (http://www.top2048.com), EETools (http://www.eetools.com), etc.

[cosmind]

hello. please tell me if you can program M35080 3 chip. I try with xprog, beeprog and M35080 programmer and nothing... M35080 3 is not the same like M35080 ???

[dreadu]

hello. please tell me if you can program M35080 3 chip. I try with xprog, beeprog and M35080 programmer and nothing... M35080 3 is not the same like M35080 ???


it should work

[wsc]

Hello guys
I have a reading problem with an MPU mc9s12dg128 mask 1L59W,i cant read it with xprog-m original with version 5
The MCU is secured,i have connect it in 23 BKGD,40 GND,41 VDD +5 and 42 RESET pins with the coaxl cable (EXTAL) but without luck
Do you have any idea?
Thanks guys

[gadroulll]

i have problem with my new x-prog m . i can read memories like 93c46 but i can not read hc05b32 .programer stops in security system. i have found a burn yellow smd capacitor 4.7uf .i can read tha one red light blinking and vcc 5v is not stable.

its a chinese clone from ecutool.

any idea to fix it or i have problem with usb 1.1?


does anyone has a schematic?

[card2diag]

hi, yes, i mention x progm v5.0, it works perfectly now and good service from that guy


it can be update?

[card2diag]

Originally Posted by card2diag http://www.digital-kaos.co.uk/forums/images/styles/digital/buttons/viewpost.gif (http://www.digital-kaos.co.uk/forums/f155/x-prog-m-54236-post755497/#post755497)
hey,your guy mean xprog 5.0?
( removed link )

hi, yes, i mention x progm v5.0, it works perfectly now and good service from that guy

did ou try update?

[joaopereira]

hi card2diag
sorry I'm new here on the site
you bought this place and this stisfeito with the product

[Yura123]

I have a clone of m XPROG, but he does not have all the authorization. How can I make all the authorization?

[Holtek]

You have to reprogram the chip ATmega64, is the only way. Unfortunately, no one has the dump :afraid:

[autotop]

hi, yes, i mention x progm v5.0, it works perfectly now and good service from that guy

can i trust you ?

[mashupishu]

Hey friends, how are you?

As you can see, I have been in the background reading, reading and reading again in order to understand all my needs.

Now it's time to buy the programmer, (I post some time ago in this thread asking for help on that matter) and now after the v4.5 to v5 upgrade revolution I'm going for a xprog-m v5 clone.

But argggg, after having read the 45 thread pages I'm still confused about where to buy it, last posts about bad blue pcbs are not something goog.

So, I have to choose :eek:, and please help me a bit:


- ecutool (http://www.ecutool.com/productshow.asp?id=2057&sortsid=3515&sorts=), ummm latest buys says that blue pcb with caps shorted and such things


- odbauto (http://obdauto.com/views.asp?hw_id=664)


- ecukey (http://ecukey.com/ProductShow.asp?ID=122)


- ebay sellers ...

Any recomendation or advice agaist any?

Anyone knows if some of them have the green pcb?

That's all, thanks in advance and happy Christmas.

[manfred2]

I welcome. I ask for drivers usb to xprog-m. the tmt party doesn't operate and urgently I need. I am thanking in advance.

[dreadu]

hi


i habe got one question i bought this too updated it with succes but now my authorization for m35080 got deleted. I have done it for 30times or so with m35080 but from today under hardware info there's written that i have no authorization for m35080 and i cant update firmware again to unlock all authorizations ? has got anybody the same problem? or any tipps?

thanks alot

and greetz

[einet]

where you by xprog?

[dreadu]

don'T know right now

[dreadu]

nobody any idea?? post 665

[Min2xx]

nobody any idea?? post 665
No, you must ask to seller

[dreadu]

but it works 30 40 times before but now m35080 authorization is gone :( Unbenannt.JPG (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=44810&stc=1&d=1293798858)

[manfred2]

What is the page Auto Service TMT ?

[dreadu]

www.tmt.lt

but it is down

[eugen8]

I use a cloned xprogm 5.0...works fine and have all authorization

[dreadu]

I use a cloned xprogm 5.0...works fine and have all authorization

have u tried m35080?

[obdmaster]

have u tried m35080?


I checked one of my xprog-m today that i updated from v4.5 to v5.0, and all authorisations are there still that i had before,


dreadu m8, it looks like its just one of them things!!!

You said youve done m35080 50 times before, well you,ve had your moneys worth out of clone xprog-m. Just buy another one theyre cheap enough m8.

All the best

Obd

[dreadu]

i bought a new one and everything works fine again :)

[ant21000]

Hello, someone please MPC56 will know how to read a command placed in a Bosch M9.7 engine of mercedes?

Thanks !

[mashupishu]

Hi friends,

I had just received (two days ago) the XPROG-m v5 that I ordered last week from ecutool, and here are my first impressions:

First of all it is the blue pcb one, this pcb seems to be more probelmatic than the green one (the lm317 and capacitors ...) but who can choose.

Second, a few bended pins on some connectors/adaptors (see attached images), nothing that can be repaired (someone played football with it?).

Third, this unit have the tantalum capacitors replaced by electrolytic smt capacitors, rated higher than the tantalum ones, 35v 4.7uF, these will prevent some capacitors fireworks :).

There still are the LM317 "D" adjustable voltage regulators, a bit "ugly soldered".

For that moment the only thing I had tested is that there exists communication with the device and if it recognizes the full authorization set.

Tomorrow I'm going to try some eeproms to see if it works (more or less).

Cheers, Mashu

[super jumbe]

Sorry to jump on the wagon but can some one confirm which one I should buy the X-Prog M or M35080V6 eeprom eraser program they both looks to be doing the same job or is one of them the latest invention, thanks for your time.

:call2:

[lupu_sandu]

XprogM don't erase M35080v6 m8

[pipmen]

can someone list some chinese suppliers for the x-prog m and the upa which work fine? So that these question is answered once for all time :)

[tehnosoftex]

can someone list some chinese suppliers for the x-prog m and the upa which work fine? So that these question is answered once for all time :)
Well, as you already know, buying from China is a lottery, therefore your question has no answer

[szogun0]

can someone list some chinese suppliers for the x-prog m and the upa which work fine? So that these question is answered once for all time :)
Price of UPA USB from China is the same as from Penko.
Buy original UPA.

[newhope]

i have dump for atmega64 + fusebits


version 4.5 and 5.0 with all authorizations


but only exchange

[cosmin12345]

hello, that pictures are not really i bad condition.All pieces are like that.

I have buy it to this xprog ,now i have questions like most of here.Hc05 Hc08 only reading,with security bypass.When modify value on hex and push write button said write error.Does anyone a solution.

thanks

[FlyJet]

Is somebody knows what is the function without authorization "Development tools"? Something special?

[Harrycz44]

Hello I buy x-prog m. revE ( USB) and M35080 programmer, x-prog work well ( I did CAS 2 BMW and EEProm 35080 ) M35080 programmer is fake or faulty item...

[exxl]

i have the x-prog-m with green pcb, but i have bought it before 2 years when it first came out with all authorizations.

till now have done hc11 secured, hc05 from mb ezs secured, micronas, tms370, hc912, 35080, bmw cas.

never had any problems with it

[mashupishu]

Hi guys!!

Well the ecutool xprom-m lasted only for one use :(, maybe it is one time use :D :D :D.

Last Friday I tried to do an autoliv airbag unit with a 9508 eeprom and when I try to read it, it makes an strange noise, like if there is a faulty capacitor, arrrgggggg, after a lot of "silent device" it did a good read, but who tries to write and mess the real content ...

Today when I arrive home I'm going to open it and try to find the faulty component and check some voltages...

My nightmare begins, this is like an Russian roulette but with eight bullets :).

I'll keep you informed about my findings....

Regardsssss, Mashu.


Hi friends,

I had just received (two days ago) the XPROG-m v5 that I ordered last week from ecutool, and here are my first impressions:

First of all it is the blue pcb one, this pcb seems to be more probelmatic than the green one (the lm317 and capacitors ...) but who can choose.

Second, a few bended pins on some connectors/adaptors (see attached images), nothing that can be repaired (someone played football with it?).

Third, this unit have the tantalum capacitors replaced by electrolytic smt capacitors, rated higher than the tantalum ones, 35v 4.7uF, these will prevent some capacitors fireworks :).

There still are the LM317 "D" adjustable voltage regulators, a bit "ugly soldered".

For that moment the only thing I had tested is that there exists communication with the device and if it recognizes the full authorization set.

Tomorrow I'm going to try some eeproms to see if it works (more or less).

Cheers, Mashu

[mashupishu]

Hi again, I did some measurements on the board.

As Zmann says on post #611 (page 41), I checked the IRF7316 having when the programmer is idle 17.9v on pins 1,2 and near 0v on 7 and 8. Also 12.3v on 3 and 4 pins and near 0v on pins 5,6.

When I hit read on device programmer desktop the outputs of the two mosfets seems to be ok, near 18v on pin 7&8 and 12v on 3&4. The bi-color led starts green and then red, and then a vibrating sound appears until the window "Device is silent" apears and I close it. While that window is open the voltages are which I said on the mosfets outputs also the vibrating sound.

I had observed too that some components get hot, not very hot but very hot for that short working time. They are marked magenta on the attached picture. What component is under the question mark?

Also it seems that the dc/dc isolator is not tightly soldered, I'm going to check that. And as I said in a previous message the capacitors under the lm317 are 35v rated, maybe any is broken?, I really don't know.



Have someone any idea about what will the problem be? (I'm trying to read a 95160 eeprom (also happens with a 95080, that was successfully read last week (no noise on the box).

Thanks in advance for your support.

Regards Machu.

[FlyJet]

Is somebody knows what is the function without authorization "Development tools"? Something special?
And buttons "Tools" and "Options" are not working.

[cosmin12345]

[QUOTE=mashupishu;942797]Hi again, I did some measurements on the board.

hy have you measure voltage at device when push read button.Is there any vcc ????If is it check wih a scope data clock etc.

report

[mashupishu]

hy have you measure voltage at device when push read button.Is there any vcc ????If is it check wih a scope data clock etc.

report

Hi cosmin12345,

I had been talking with Zmnan, and after some tests the programmer doesn't have a repetitive behavior. After many measures with the multimeter it starts reading ok, writing with external power supply, and sometimes the strange sound disappears. Now it doesn't makes any sound.

Our conclusion is that the LT1072 is faulty/broken/degraded, as is used as step-up voltage converter and there is only 4.7v on the positive leg of the 220uF electrolytic capacitor, and it must be 12v.

So I ordered some LT1072 in order to change that, also Zmnan suggested me that if I can't find this part I could try the LT1172 as used in the green pcb version of xprog-m.

I can't have access to the scope until that weekend, so I'll report the measurements over the 95160.

In the meantime a mate near my location sell a green-pcb xprog, so I decided to buy it (more expensive that mine) for doing the stuff I need. Late when I receive the replacement parts and the xprog was repaired I'll try to sell it to someone interested in (making sure that it works perfectly).

That's all, I'll post the measurements and some pics about the new programmer.

Thanks, and best regards. Mashu.

( I also wants to give thanks to Zmnan for his kind and friendly support, thanks mate)

[cosmind]

same problem for me. I can read HC05, but canot program it but tms370 read/write ok

[iqcaraudio]

my xprog m clone is showing an error when i use it with 68hc05l28, it says its not compatible with windows NT, i'm using windows XP sp3... i tried installing xprog desktop 4.5 and 5 on windows 98 but I can't get it to work... any ideas?

[Zmann]

Windows NT in term of Xprog SW covers windows Xp too.

Sorry, overlooked you did try wins 98 already. No idea.

[iqcaraudio]

I can't install xprog 4.5 on windows 98, it shows access violation on some address and xprog 5 doesnt really work at all on windows 98...

[elchip]

same problem for me. I can read HC05, but canot program it but tms370 read/write ok

The problem on blue PCB's IRQ voltage is not 10V but max 8.5 so is not enought ( look at datasheet of motorola for specific device ). So you must repair adjustment circuit in LM317 which supply IRQ ( Vpp ) voltage to set exact needed voltage.
All problem will go away ..

>> That manufacturer who make blue PCB not usage standard component's with precise values which is in original project of XprogM.

Regard's

[elchip]

Here we go...
For all DK members for free how to fix XprogM blue PCB problem
if it not work good HC05 and HC705 MCU.
First measure IRQ when you hit read or write to see if mod need and if need here is picture how do that...
Start with 1K5 and measure IRQ voltage without HC05 adapter just hit READ and measure if voltage is little bigger
example 10.4V then you need 1k5 + 100 ohm in serie to get 1k6 and again measure...
When you measure from 9.5 V to maximum 10V you is in range.
Usual XprogM usage VppR for IRQ - that is Vpp from LM317 via 4K7 internal resistor.
So you can easy measure Vpp in programing progress .So Vpp will be little highter then VppR cos VppR drop voltage on 4k7 resistor about 50 mV or so ...
If you measure Vpp = 9.75V VppR will be about 9.17V...

>>> Next I will remove linear stabilizer for 5V and replace with some better or maybe DC-DC one. On LM stabilizer is too much heating...
Conclusion is on china XprogM is to many low cost part's ...

That is all...

49266

:manuscarf:

Regard's to all

[cosmind]

I tryed this on xprog with green pcb and after I canot read tms and canot write HC05

[elchip]

I tryed this on xprog with green pcb and after I canot read tms and canot write HC05

My MOD work 1000% .
If you probe before my post why you didn't post your test ?
Did you know for what is that resistor ?
Can you explanation why you do that and why on green PCB ? Green PCB have good voltage and there not reasn to do that....
Maybe you do over voltage ....
Which value of resistor you usage ? Which voltage you measure and on which pin ?
So can you little explain to as to we know better ;-) ?

:stupido2:

[cosmind]

I have green pcb and I canot write HC05. I changed 182 with 152 like in the picture. but I forgot to check the voltage. I selled xprom to someone how need it only for tms

[Zmann]

The Vppr voltage are used on various devices at least found on both HC05 and HC08. Xprog-m has no dedicated Vpp voltage control for different devices. HC08 needs this Vpp of max. 9 volts on IRQ pin. I would pay attention on HC08 mode as well when doing modification.

When people said Xprog-m 'not writing' on HC05, were they meaning on security mode? If yes, it is different issue.

[elchip]

The Vppr voltage are used on various devices at least found on both HC05 and HC08. Xprog-m has no dedicated Vpp voltage control for different devices. HC08 needs this Vpp of max. 9 volts on IRQ pin. I would pay attention on HC08 mode as well when doing modification.

When people said Xprog-m 'not writing' on HC05, were they meaning on security mode? If yes, it is different issue.


Look on motorola datasheet all motorola MCU for IRQ usage Vdd X 2 ...
So no place in datasheet precise Vpp on IRQ pin !
Cos some devices work on 5V Vdd and need 10V Vpp , and devices which usage 3.3V need 6.6V on IRQ..
So you cant say 9V ...
Simple is Vpp ( IRQ ) = Vdd X 2 that all.

And I know to XprogM cant do security HC05B16 cos it need full different configuration like in ETL to go to bootstrap special mode jump to desired address etc etc ...
But it is different story ...
Regard's

[Zmann]

Look on motorola datasheet all motorola MCU for IRQ usage Vdd X 2 ...
So no place in datasheet precise Vpp on IRQ pin !
Cos some devices work on 5V Vdd and need 10V Vpp , and devices which usage 3.3V need 6.6V on IRQ..
So you cant say 9V ...
Simple is Vpp ( IRQ ) = Vdd X 2 that all.

And I know to XprogM cant do security HC05B16 cos it need full different configuration like in ETL to go to bootstrap special mode jump to desired address etc etc ...
But it is different story ...
Regard's


Here we go...
For all DK members for free how to fix XprogM blue PCB problem
if it not work good HC05 and HC705 MCU.
First measure IRQ when you hit read or write to see if mod need and if need here is picture how do that...
Start with 1K5 and measure IRQ voltage without HC05 adapter just hit READ and measure if voltage is little bigger
example 10.4V then you need 1k5 + 100 ohm in serie to get 1k6 and again measure...
When you measure from 9.5 V to maximum 10V you is in range.
Usual XprogM usage VppR for IRQ - that is Vpp from LM317 via 4K7 internal resistor.
So you can easy measure Vpp in programing progress .So Vpp will be little highter then VppR cos VppR drop voltage on 4k7 resistor about 50 mV or so ...
If you measure Vpp = 9.75V VppR will be about 9.17V...

I cant find on any HC08 datasheet say the Vpp on IRQ pin being 'Vddx2' neither ! But mostly the instructions are the IRQ input voltage of Vdd+4V as maximum rating.

So I can say 9v.

Some device of HC'9'08 can be found as Vdd+4.5v as the maximum rating, those should be far from problem to the modification of 9volts++

Regards

[elchip]

I cant find on any HC08 datasheet say the Vpp on IRQ pin being 'Vddx2' neither ! But mostly the instructions are the IRQ input voltage of Vdd+4V as maximum rating.

So I can say 9v.

Some device of HC'9'08 can be found as Vdd+4.5v as the maximum rating, those should be far from problem to the modification of 9volts++

Regards
Here is help from one not low cost programming tool ;-)
So maybe they do wrong too ...

49600

:stupido2:
Also here is original data from HC08AZ32 datasheet.
So if Vdd = 5V ( oas you say 4.5V ) but never 4V ...
Motorola give IRQ = Vdd + VHI ( where we all know to HI level is Vdd ) so VHI must be from 4.5V to 5V which give IRQ = 9.5V-10V but we can usage 9 without problem cos 4V as VHI is also high logic level 100%.
But we cant say to 8V is good value as is in blue PCB so ...

Here is part from original HC08AZ32 datasheet:

49601

:ciao:

Regard's

[Zmann]

I did not say Vdd 4.5v, to mark out Vddx2 of 9v. No Vddx2 story in HC08 literatures but always refered as Vdd + something. :D

I disagree to hold Vpp at 8v neither and 100% agree to this modification. Ive made major modifications on my blue board too as well as a successful test on 'HC05 security adapter not writing problem'. Just pointing out that the setting Vpp to or close to 10v may break over some HC08 device IRQ maximum rating.

In the more up-to-date original Motorola HC08 documents, IRQ (and not as IRQ1 from the 1997 doc.) maximum IRQ voltage always presents in Maximum Ratings table as below samples e.g. HC08AZ32, AZ60 and AS60 at Vdd+4v and some other at Vdd+4.5v.

Happy modifying

Regards

[tomuch]

one question where i can buy an good xprog-m clone i read so much my head is smoking.

wbrgds
michael

[elchip]

I did not say Vdd 4.5v, to mark out Vddx2 of 9v. No Vddx2 story in HC08 literatures but always refered as Vdd + something. :D

I disagree to hold Vpp at 8v neither and 100% agree to this modification. Ive made major modifications on my blue board too as well as a successful test on 'HC05 security adapter not writing problem'. Just pointing out that the setting Vpp to or close to 10v may break over some HC08 device IRQ maximum rating.

In the more up-to-date original Motorola HC08 documents, IRQ (and not as IRQ1 from the 1997 doc.) maximum IRQ voltage always presents in Maximum Ratings table as below samples e.g. HC08AZ32, AZ60 and AS60 at Vdd+4v and some other at Vdd+4.5v.

Happy modifying

Regards

So we now on same way....
If you have some interest MOD too please to post.
Then we all can end story about bad china clone of XprogM.

My best regard's to all

[bordom]

Blue pcb, 280 Ohm Resistor, LM2940CS, LT1072, B05050S-1W, coil 6485(?), 220uF 50V,

[elchip]

Blue pcb, 280 Ohm Resistor, LM2940CS, LT1072, B05050S-1W, coil 6485(?), 220uF 50V,
Wrong reading of resistor , it is 182 = 1k8 !
It is rotated 180 degree in soldering process...
With 280 ohm you will read on IRQ 16V " DANGER " .
On standard LM317 circuit it is recommended to be 270 ohm but here is different....
So with 1k5 + 100 ohm connected in series on his place it will be UNLOADED exact 9.85V and with load 9.5V which is perfect.

Regard's

:bird:

[bordom]

Yes indeed I was braindead. Sorry.
Thank you.

[EduardNN]

A lot of problems with the clone Xprog-M due to the application rejected, cheap components.
We need to change atmega64 to normal.
Search for a dump ...

[taihei]

Hi elchip,

After you modified that resistor , is there any side effect for other mpu except hcxx??

[Tereksaz]

i have dump for atmega64 + fusebits


version 4.5 and 5.0 with all authorizations


but only exchange
change to dumps for mpps 3.0.2.37

[fuktak]

Guys check this link.They sells a lot of programmers that works fine.They price is cheeper than Chinese.WBR.???-Prog-M - ????? ?????+????? = 140&#036; ? ????????? - ????????????? ?????? Oktja.ru (http://www.oktja.ru/forum/topic/95796-%D0%A1%E2%80%A6%D0%A1%E2%80%A6%D0%A1%E2%80%A6-prog-m-%D0%A0%D0%85%D0%A0%C2%B0%D0%A0%C2%B1%D0%A0%D1%95%D 0%A1%D0%82-%D0%A0%D1%97%D0%A0%C2%BB%D0%A0%C2%B0%D0%A1%E2%80%9 A%D0%A1%E2%80%B9%D0%A0%D1%97%D0%A1%D0%82%D0%A0%D1% 95%D0%A1%E2%80%A0%D0%A1%E2%80%B9-140-%D0%A1%D0%83-%D0%A0%D2%91%D0%A0%D1%95%D0%A1%D0%83%D0%A1%E2%80%9 A%D0%A0%C2%B0%D0%A0%D0%86%D0%A0%D1%94%D0%A0%D1%95% D0%A0%E2%84%96/)

[carradio2001]

I have clone V5.0 X-prog-m programmer.
I try to read ST10F269. Every time stops at 16% or 19%.
Any tips ?

Thanks in advance.

Carradio2001.

[bram380]

now, x-progm clone (http://www.carsung.net/EN/Index.asp) only US $88
China clone, russia clone, etc clone, xyz clone are the same.

The important thing is how we use it with the support of science and the right trick

[elchip]

Hi elchip,

After you modified that resistor , is there any side effect for other mpu except hcxx??
The resistor effect only on HCXX.
So if any other trick or type please other member's to write as help to all of as here.

Many thanks to all

[vanos batam]

how to program 5p08 in circuit with X prog M?
thanks

[cardoctor]

Try with kwp2000+
Or galetto

[elchip]

how to program 5p08 in circuit with X prog M?
thanks

Any in circuit programming of eeprom can be with fatal error , so I always desolder it ....

Regard's

[EduardNN]

Guys check this link.They sells a lot of programmers that works fine.They price is cheeper than Chinese.WBR.???-Prog-M - ????? ?????+????? = 140***036; ? ????????? - ????????????? ?????? Oktja.ru (http://www.oktja.ru/forum/topic/95796-%D0%A1%E2%80%A6%D0%A1%E2%80%A6%D0%A1%E2%80%A6-prog-m-%D0%A0%D0%85%D0%A0%C2%B0%D0%A0%C2%B1%D0%A0%D1%95%D 0%A1%D0%82-%D0%A0%D1%97%D0%A0%C2%BB%D0%A0%C2%B0%D0%A1%E2%80%9 A%D0%A1%E2%80%B9%D0%A0%D1%97%D0%A1%D0%82%D0%A0%D1% 95%D0%A1%E2%80%A0%D0%A1%E2%80%B9-140-%D0%A1%D0%83-%D0%A0%D2%91%D0%A0%D1%95%D0%A1%D0%83%D0%A1%E2%80%9 A%D0%A0%C2%B0%D0%A0%D0%86%D0%A0%D1%94%D0%A0%D1%95% D0%A0%E2%84%96/)

This is a set of self-assembly 140$

[makura]

hi
just got me a xprog mfrom china,question.Can xprog-m read mcu mc68hcp11a1vfn c11w and what adapter do i need to use?by the way mine is version 5.
thanks in advance

[makura]

tried reading a hc11a1(8) from a peugeot 306 ecu and the programmer keept on saying DEVICE IS SILENT.
I will open it tomorrow and see what colour the pcb is and will post here.

[Zmann]

You did not say what the ECU type, that should be IAW 8Pxx in PSA car which contains mc68hcp11a1vfn. I read/write this ECU/MCU with Xprog-m (clone) with no problem without any pin lift. The devices in menu either HC11A1(C11W) or HC11A8-old (set to 8000000hz) works no difference.

[makura]

You did not say what the ECU type, that should be IAW 8Pxx in PSA car which contains mc68hcp11a1vfn. I read/write this ECU/MCU with Xprog-m (clone) with no problem without any pin lift. The devices in menu either HC11A1(C11W) or HC11A8-old (set to 8000000hz) works no difference.
Hi
the ecu is from a peugeot 306 magnet marell IAW 08P.1C,when i try to read with either of the selection you have listed above i get device silent,by the way my xprog has a green board.
Thanks again for your reply.

[rappttor]

does anybody used vw dashobord module with micronas to change km? is it any good?
i have a mk5 dashbord with cdc3272, this config it is present in xprog only in skoda and caddy; but in my case if i use it it reads mabo jambo (no real pin or km).
anyway, xprog read micronas dump after several atempts...

[episcop]

does anybody used vw dashobord module with micronas to change km? is it any good?
i have a mk5 dashbord with cdc3272, this config it is present in xprog only in skoda and caddy; but in my case if i use it it reads mabo jambo (no real pin or km).
anyway, xprog read micronas dump after several atempts...

With wv cdc3272&24c32 (2006-2007), Xprog don't hav any problem with my..

[rappttor]

does it bypass security every time or you must take several atempts?

[tor2lehel]

Anybody help me!! Xprog-m support the CR16MFR PLCC 44 ?????

[F4kk3r]

Anybody has the 2010-05-12 version?
Thanks

[lawdog1]

Look on motorola datasheet all motorola MCU for IRQ usage Vdd X 2 ...
So no place in datasheet precise Vpp on IRQ pin !
Cos some devices work on 5V Vdd and need 10V Vpp , and devices which usage 3.3V need 6.6V on IRQ..
So you cant say 9V ...
Simple is Vpp ( IRQ ) = Vdd X 2 that all.

And I know to XprogM cant do security HC05B16 cos it need full different configuration like in ETL to go to bootstrap special mode jump to desired address etc etc ...
But it is different story ...
Regard's

What is the difference between a resistor labeled 151 152 154? Basically, what does the last number mean, and can I use a 154 or 151 instead of 152? I have some 151 and 154 and they both are sold as 150K resistor.

Thanks!

[makura]

What is the difference between a resistor labeled 151 152 154? Basically, what does the last number mean, and can I use a 154 or 151 instead of 152? I have some 151 and 154 and they both are sold as 150K resistor.

Thanks!Hi
It goes like this !!! 151=150 which means it's 15 and the 1 representing the number of zero's after the 15,so 152=1500 to get the proper value you have to say 1500 divided by 1000 and the 1000 meaning KILO(1000) so this resistor would be 1,5kilo ohms.
154=150000 so this would be 150kilo ohms(150k) etc etc
Hope i explained it as simple as possible since i am not a lecturer,and if not understood fire away.

[makura]

any one know how to read and write 28c64 and 29f400 using xprog-m

[wsc]

I have clone V5.0 X-prog-m programmer.
I try to read ST10F269. Every time stops at 16% or 19%.
Any tips ?

Thanks in advance.

Carradio2001.

I have the same problem
But if you live it about 3hours maybe you can read it again

[lawdog1]

Hi
It goes like this !!! 151=150 which means it's 15 and the 1 representing the number of zero's after the 15,so 152=1500 to get the proper value you have to say 1500 divided by 1000 and the 1000 meaning KILO(1000) so this resistor would be 1,5kilo ohms.
154=150000 so this would be 150kilo ohms(150k) etc etc
Hope i explained it as simple as possible since i am not a lecturer,and if not understood fire away.

Thanks! I understand what you are saying. Bottom line is I need 1500 and that would be 152! 154 would be way too much voltage drop then, and 151 not enough.

I want to do like one of the other users above did and make the blue pcb xprogm stronger. We don't have an electronics store close by so i was trying to go through old SRS control units and ECUs to find the parts I need with no luck ...

And then comes the hard part, learning how to actually connect to the chips lol. I'm pretty smart and technical, but I have 0 experience reading any chips other than removing a simple 8-pin soic and reading it out of circuit. Unfortunately, there isn't much info (or people aren't willing to give info) on how to actually read the chips in circuit. I'm getting a little worried because I see some people who claim they never do in-circuit programming because of the dangers. And on top of that I have a blue PCB xprogm so there are so many variables for me to overcome. If I can't read a chip, it could be the programmer or me not knowing what I am doing, or me having burned something in circuit :banghead: I guess it wouldn't be fun if it were easy right?

[exxl]

Anybody help me!! Xprog-m support the CR16MFR PLCC 44 ?????


Big NO!

it cant read cr16mfr !

[carradio2001]

I have the same problem
But if you live it about 3hours maybe you can read it again
3 hours ? the x-prog or the module with st10f269 ? after these 3 hours will be read it fully ?

Carradio2001.

[wsc]

3 hours ? the x-prog or the module with st10f269 ? after these 3 hours will be read it fully ?

Carradio2001.

the module mate
i have original xprog-m and for me works every time
I think that the proccesor lock for some reason some sectors thats why we cant read or write
good luck
Every time you must erase it first the writting

[makura]

Thanks! I understand what you are saying. Bottom line is I need 1500 and that would be 152! 154 would be way too much voltage drop then, and 151 not enough.

I want to do like one of the other users above did and make the blue pcb xprogm stronger. We don't have an electronics store close by so i was trying to go through old SRS control units and ECUs to find the parts I need with no luck ...

And then comes the hard part, learning how to actually connect to the chips lol. I'm pretty smart and technical, but I have 0 experience reading any chips other than removing a simple 8-pin soic and reading it out of circuit. Unfortunately, there isn't much info (or people aren't willing to give info) on how to actually read the chips in circuit. I'm getting a little worried because I see some people who claim they never do in-circuit programming because of the dangers. And on top of that I have a blue PCB xprogm so there are so many variables for me to overcome. If I can't read a chip, it could be the programmer or me not knowing what I am doing, or me having burned something in circuit :banghead: I guess it wouldn't be fun if it were easy right?
The resistor you need should be 153 that gives you 15k plus a 102 which is 1killo ohm connect them in series(inline)then combined they will give you 16k

[lawdog1]

The resistor you need should be 153 that gives you 15k plus a 102 which is 1killo ohm connect them in series(inline)then combined they will give you 16k

Ok now I am confused. I'm not confused with the math, but with the mod itself. The original resistor that the blue pcb has is 182. So this is 1.8K or 1800 ohms. User elchip in post #699 on page 47 says to use 152 +100 in series to make 1600 ohms. But in his picture attached to his post, he instructs only to change the 182 to 152, so that makes it 1500 ohms, not 1600. But you are saying to do 153, which is 15,000 ohms plus 102, which is 1000 ohms, for a total of 16K? Wouldn't that lower the voltage too much? Also, is there even any room to put two resistors in series?

In Zmann's post, #707 page 48, he also uses 152 in place of the 182 (so 1.5K). I don't see any other resistors added? Also, I am trying to figure out what other mods he made. I see he changed the capacitors, but not sure if his are stronger than the ones that came with mine. I have some of the small yellow ones that I think are weak, but the ones near the 152 resistor are silver barrel style caps.

Also, I am trying to figure out which style LM317 he used. I googled it and see there are many different styles, with some being adjustable (not sure what that means). Any idea which lm317 I should buy? There are LM317LDR2, LM317LBDR2G, LM317LBDG, LM317LDR2G and so on ...

Thanks again for your replies

[lawdog1]

Also I measured my vpp is 9v

[lawdog1]

Hi
the ecu is from a peugeot 306 magnet marell IAW 08P.1C,when i try to read with either of the selection you have listed above i get device silent,by the way my xprog has a green board.
Thanks again for your reply.

BTW, if you didn't figure it out already, device is silent probably means you don't have the com port set up properly, either the device driver itself, or the setting in the xprogm software. Make sure the USB drivers are installed correctly, make sure you see the USB COM driver show up in your device manager, and then go to Environment settings (or something like that, trying to remember from memory) in the Xprog software and select the right com port.

Device is silent for me meant the software was not communicating with the programmer, not that it wasn't reading the chip.

I originally got the same error as you. I noticed that the xprogm software resets this setting, and that also the device doesn't sometimes show properly. I resolved this by disconnecting and reconnecting the Xprog USB, and also reselecting the proper COM port device in the Xprog software.

After I got that setup, I tried reading an 8pin 93xx46 chip in circuit. At first I got pin errors. I played with the connections by moving them a little, and then it read fine! Now to learn how to do MCUs in-circuit .... Does anyone know if they HAVE to be done in circuit, or should I always remove them? I seem to remember someone saying that the MCUs with encryption have to be done in-circuit? Otherwise you can't access the memory? Is this true? I think I prefer to remove the chips when possible because I realized today how hard using test clips are to get a good connection.

[Zmann]

Ok now I am confused. I'm not confused with the math, but with the mod itself. The original resistor that the blue pcb has is 182. So this is 1.8K or 1800 ohms. User elchip in post #699 on page 47 says to use 152 +100 in series to make 1600 ohms. But in his picture attached to his post, he instructs only to change the 182 to 152, so that makes it 1500 ohms, not 1600. But you are saying to do 153, which is 15,000 ohms plus 102, which is 1000 ohms, for a total of 16K? Wouldn't that lower the voltage too much? Also, is there even any room to put two resistors in series?

In Zmann's post, #707 page 48, he also uses 152 in place of the 182 (so 1.5K). I don't see any other resistors added? Also, I am trying to figure out what other mods he made. I see he changed the capacitors, but not sure if his are stronger than the ones that came with mine. I have some of the small yellow ones that I think are weak, but the ones near the 152 resistor are silver barrel style caps.

Also, I am trying to figure out which style LM317 he used. I googled it and see there are many different styles, with some being adjustable (not sure what that means). Any idea which lm317 I should buy? There are LM317LDR2, LM317LBDR2G, LM317LBDG, LM317LDR2G and so on ...

Thanks again for your replies

All of LM317's are the type of an adjustable voltage regulator IC. I made in a post possibily in this threat saying that 'THE TWO LM317 TO-92 PACKAGE USED IN THE BLUE XPROG-M CANNOT BE REPLACED WITH LM317 SOIC8 PACKAGE' like used in the green PCB unless the PCB lines are modified like mine, wrong lining in the blue PCB for SOIC8 package!

Resistor of 1.8 Kohm (between 1.5 and 1.8 K) is one of the voltage adjusting elements, typically should be a potentiometer (adjustable resistor) but here after well calculated they used fixed resistor of 1.8 Kohm. If only one SMD resistor of 1.6 Kohm (type 0805) is prefered as a replacement, I found that it's also available but may need slight effort to find them.

The blue Xprog in the photo is of the later built which they already replaced the small yellow and under rated tantalum capacitors with electrolytic capacitors of 35V rating (silver barrel).

[makura]

sorry mate my mistake,your resitor should be 1.5k plus 100ohm resitor in series to giv you 1.6kohm,

[tihiuvek]

Have you tried to use COM port cable? I had similar problem, so I been playing with USB parameters (latency ...). After that I successfully read it but not every times.
At the end I connect my X-prog over Com cable and additional power supply and it works perfectly.

[makura]

Have you tried to use COM port cable? I had similar problem, so I been playing with USB parameters (latency ...). After that I successfully read it but not every times.
At the end I connect my X-prog over Com cable and additional power supply and it works perfectly.Hey you right that is how got to read hc11a1 micro,i think there is somthing wrong with the usb drivers,if using com port it reads and writes with out any problems

[i_shot_the_sheriff]

I've read some posts on this thread!! but i couldn't understand which is a good china shop to get the xprog!!
Sooo what shop should i pick?

thanks

[makura]

I've read some posts on this thread!! but i couldn't understand which is a good china shop to get the xprog!!
Sooo what shop should i pick?

thanks
I got mine from autotoolscan.com and the sales person is May