CAS3 0L15Y dead

[Bart86]

Hi.
Customer states after battery went dead car stop starting .No response from cas ,dead dashboard ,not recognizing orginal key not even showing message when i put different key . What i did ,read eeprom with r260 rosfar ,write different epprom from spare CAS that i have with working key and orginal cas is back to life,dash lights cranking ok but no start of course -ISN VIN not matching .But that tells me my flash is "Ok "?
I read files with Rosfar - but cant write flash -r260 not supporting writing flash ,only eeprom .
Other 2 files I read with xprog

Can somebody correct my files .

mcu
MC9S12XDP512
MASK 0L15Y

Thanks

[paulsta]

Hi.
Customer states after battery went dead car stop starting .No response from cas ,dead dashboard ,not recognizing orginal key not even showing message when i put different key . What i did ,read eeprom with r260 rosfar ,write different epprom from spare CAS that i have with working key and orginal cas is back to life,dash lights cranking ok but no start of course -ISN VIN not matching .But that tells me my flash is "Ok "?
I read files with Rosfar - but cant write flash -r260 not supporting writing flash ,only eeprom .
Other 2 files I read with xprog

Can somebody correct my files .

mcu
MC9S12XDP512
MASK 0L15Y

ThanksWhere are you located Bart?

Sent from my Pixel 2 XL using Tapatalk

[p1et]

Of course you can write flash with r260

[Bart86]

Of course you can write flash with r260This mcu is not supported in r260 for writing flash. Only eeprom.

Sent from my VTR-L09 using Tapatalk

[pepi]

Use R270 , xprogM or VVDI prog

[hojo25]

Hi.
Customer states after battery went dead car stop starting .No response from cas ,dead dashboard ,not recognizing orginal key not even showing message when i put different key . What i did ,read eeprom with r260 rosfar ,write different epprom from spare CAS that i have with working key and orginal cas is back to life,dash lights cranking ok but no start of course -ISN VIN not matching .But that tells me my flash is "Ok "?
I read files with Rosfar - but cant write flash -r260 not supporting writing flash ,only eeprom .
Other 2 files I read with xprog

Can somebody correct my files .

mcu
MC9S12XDP512
MASK 0L15Y

Thanks

EEprom file where read with Xprog is OK.
The other EEprom file can not be read and is bad.

[kazikk]

Try this eeprom

[Bart86]

Try this eeprom

Thanks Kazik for trying but still no luck ,cas is still dead

[Bart86]

EEprom file where read with Xprog is
The other EEprom file can not be read and is bad.

Other eeprom is read by r260 and is in diffrent format but read is ok

[hojo25]

Thanks Kazik for trying but still no luck ,cas is still dead

The EEprom is fine.
So the flash will be broken.
Try to reach Tool32 CAS.
If that works flashing with Winkfp again.

[Bart86]

That wouldnt make sens. I use my donor eeprom +key and i write to orginal cas and everything start working . When i use epprom from orginal cas and transfer to donor CAS is dead .

[hojo25]

That wouldnt make sens. I use my donor eeprom +key and i write to orginal cas and everything start working . When i use epprom from orginal cas and transfer to donor CAS is dead .

And is the ignition on?

[Bart86]

And is the ignition on?With donor eeprom ignition ON and cranking but no starting. With Ori file no response on cluster at all . But u can communicate with Cas but no errors and not recognizing any key and cluster not even showing u that u using wrong key

Sent from my VTR-L09 using Tapatalk

[hojo25]

Did you send EEprom from CAS Original?
And EEprom used by CAS?

[Bart86]

Did you send EEprom from CAS Original?
And EEprom used by CAS?

Only orginal files

[hojo25]

Did you try to balance a DME - CAS with Inpa or ISTA - D?

[droidwayne65]

Hi.
Customer states after battery went dead car stop starting .No response from cas ,dead dashboard ,not recognizing orginal key not even showing message when i put different key . What i did ,read eeprom with r260 rosfar ,write different epprom from spare CAS that i have with working key and orginal cas is back to life,dash lights cranking ok but no start of course -ISN VIN not matching .But that tells me my flash is "Ok "?
I read files with Rosfar - but cant write flash -r260 not supporting writing flash ,only eeprom .
Other 2 files I read with xprog

Can somebody correct my files .

mcu
MC9S12XDP512
MASK 0L15Y

ThanksThat was a fantastic battery disconnect, that wiped all the keys in eeprom and set identical crypto/password data. I suggest you get the real story from your customer. Also read and post the data from what is presumed to be the original key.

[Bart86]

That was a fantastic battery disconnect, that wiped all the keys in eeprom and set identical crypto/password data. I suggest you get the real story from your customer. Also read and post the data from what is presumed to be the original key.Finally droidwayne65 have answer for me to put puzzle together bc story with dead battery didn't make sens to me either. But other thing is car come with key that don't have comfort access but car have comfort access

Sent from my VTR-L09 using Tapatalk

[Bart86]

Finally droidwayne65 have answer for me to put puzzle together bc story with dead battery didn't make sens to me either. But other thing is car come with key that don't have comfort access but car have comfort access

Sent from my VTR-L09 using Tapatalk

droidwayne65 u were right ,after 30 min on the phone with 3 diffrent people story change . Owner - battery went dead could start ,send car to shop for new battery -sounds about right .Guy from the shop told me they put battery but still was no start/dead dashboard ,Hi couldnt scanned ,send car to his cousine and he call his friend show up with diffrent scanner and the friend of his play with snanner for 2hr - I ask what type of scanner was and if he can remeber- ...otosys ...i google that and is chines scanner with option for cas .

We have answer ,Battery wasn`t the only thing that was done to the car .

[betoRJ]

Your flash file is horrible !!! Wrong size and corrupted !!!

with worng size you will never write !!!


write this good one from your cas