Nissan Juke 2012 petrol Engine Won't Turn Over and Won't Start after key programming

[super jumbe]

I have used truecode with glovebox pincode.
Car came to garage for spare key after battery was dead all went good after 6 days customer said the old key stopped working, the new key was working good, when I went to programme old key it says pin not accepted, now both keys won't start car, is there any solution? Is there any way if I remove BSI and make key, the other issue I have noticed the fault code will not be erased, any help very much appreciated thanks.:uncomfortableness::uncomfortableness::unco mfortableness:

[super jumbe]

779393

Thia was the fault codes.

[lion0304]

Juke i've did alway 4 digits pincode. Even model 2015.

[Weasel3]

Ignition key I presume?

Yes, it is in the list of Tang.
2010 and 2011
Two different types of eeprom.
Maybe one is for regular and the other for prox. But I am not sure.

[rob h]

Do you have a better picture, with the dtc on it?

[Manta1600]

Juke i've did alway 4 digits pincode. Even model 2015.

Yesterday I've done Juke 2017 AKL with 4 digit pin code with smart key

as you told, all Juke's that I had was 4 digit code

-----------------------

Maybe exist juke with Micra immo that need glovebox code

on Micra I had problem after flat battery the car forgot the original key I reprogrammed the key and the customer sell the car on 1 hour driving from me

after 1 week he call me that the car lost the key again, then I went there and I programmed new and reprogrammed the original one for free

After 1 month the customer told me that the car again can't recognise the keys and I told him that I don't wan't to see any more this car

[rapidlocksmiths]

most are four digit but there is also some that require glovebox code converting , plenty have seen these though i havnt and all ive done have been 4 digit.

[super jumbe]

I used GLOVEBOX 12 digit label number then gave me the pincode when I last used to programme new spare key.
Glove box sticker label number: A372AF1703E9
Gave me this code to programme: 1430DAD556A2
I used truecode was asking for 12 digit pincode, look I have done with truecode lots of Nissan this is the one giving me the issue, look whats the solution?

[Manta1600]

I used GLOVEBOX 12 digit label number then gave me the pincode when I last used to programme new spare key.
Glove box sticker label number: A372AF1703E9
Gave me this code to programme: 1430DAD556A2
I used truecode was asking for 12 digit pincode, look I have done with truecode lots of Nissan this is the one giving me the issue, look whats the solution?

Did you press the clutch?

is the car is on P if is automatic?

What happens when you switch ignition ON is the lights comming on the dash?

Post better picture on the faults

[lion0304]

I've never met yet key lost in memory. But i repair many NATS5 immobox around ignition lock that just ignore the key.

Maybe in Micra, wirring problem or BCM? I don't think memory can lose easy by that way.

Also SSangyong immobox many not recognise keys, you can recode but problem come back again. I alway repair and say goodbye.

[key4man]

I recently made a akl to this vehicle, using Zed full, the problem was that I could not make a second key that the customer wanted no matter what I tried.
For your problem , try to do programming using another device, maybe it will work

[super jumbe]

I recently made a akl to this vehicle, using Zed full, the problem was that I could not make a second key that the customer wanted no matter what I tried.
For your problem , try to do programming using another device, maybe it will work

I could understand as said but other tools asking for 4 digit pin how can I get 4 digit pin when this car has glovebox label only do I have to read BSI dump for this thanks.

[key4man]

I could understand as said but other tools asking for 4 digit pin how can I get 4 digit pin when this car has glovebox label only do I have to read BSI dump for this thanks.
I'm not sure about the other devices, but regarding the zed full it bypasses the code, I suggest you try to disconnect the cables of the battery Connect them together to drain the power from the vehicle, reconnect and see what happens

[super jumbe]

I did discnnected battery over night no joy look at the pictures programming with truecode.
779471

779472

779473

779474

779474

[super jumbe]

Has any one made a key from BSI Dump on Juke 2012 with tango?

[Manta1600]

Has any one made a key from BSI Dump on Juke 2012 with tango?

Never had problem with Truecode and don't know about Tango

but if Truecode don't work maybe BCM is faulty and also Tango will fail

What key use this 7936 or 7946?

[super jumbe]

Never had problem with Truecode and don't know about Tango

but if Truecode don't work maybe BCM is faulty and also Tango will fail

What key use this 7936 or 7946?

PCF7936 ID46

[super jumbe]

I removed BSI and read chip R66 no keys in the dump, I programmed new key and now key is in the dump the pincode are al [FFFF] I will replace BSI tommorow fingers crossed look at the dump immage.

779532

779533

[Manta1600]

I removed BSI and read chip R66 no keys in the dump, I programmed new key and now key is in the dump the pincode are al [FFFF] I will replace BSI tommorow fingers crossed look at the dump immage.

779532

779533

Maybe will be better to repair this one - try to find other files from the same model and compare them

I dont think that the new BSI will be plug and play and you will need to adapt maybe Autel can do it

[lion0304]

For Juke, i use X100 Pad2, choose 4 digits then read BCM to get new pin.

So just follow instruction and done. Also, Nissan and almost other brands need the good PCF7936 (i've some chinese PCF7936 not work for Nissan, only for PSA cars)

[A22]

Was it not possible to clone original key?

Sent from my SM-A505FN using Tapatalk

[Manta1600]

Was it not possible to clone original key?

Sent from my SM-A505FN using Tapatalk

If the car can't recognise the original key I don't think that he can copy the chip

also if he copy non working chip the new one also will be useless

[A22]

I ment from the beginning

Sent from my SM-A505FN using Tapatalk

[Manta1600]

I ment from the beginning

Sent from my SM-A505FN using Tapatalk

Maybe because copy the chip doesn't looks professional :)

[lion0304]

Maybe because copy the chip doesn't looks professional :)


That right. Cloning ins't a good solution. Not for security, not for benefit. I do only when: Client need the cheapest, almost for used car resellers.

For most people, when you take a little time explain them why you program by OBD, almost of them agree to pay more than key cloning.

[p1et]

Cloning is best soution for crap cars like this

[super jumbe]

No joy car did not start, the reason I did not cloned the chip because Nissan and truecode 2 min job never let me down, this was the one for some reason just did not accept the pincode and all keys stopped working, look I am going to programme with 4 digit code can someone able to give me the pincode from this dump thanks.

[super jumbe]

This was the original file.

[newone]

all ffff my friend

[sexyceta]

vvdi say ffff

[Weasel3]

I used GLOVEBOX 12 digit label number then gave me the pincode when I last used to programme new spare key.
Glove box sticker label number: A372AF1703E9
Gave me this code to programme: 1430DAD556A2
I used truecode was asking for 12 digit pincode, look I have done with truecode lots of Nissan this is the one giving me the issue, look whats the solution?

I also experience Glovebox sticker 12 digit label and convert on a JUKE 2012, ignition key. And it was sure not 4 digit pin. (But I understand that 4-digit is most common).
Tried all my tools back and forwards, before a solution came up.
Eventually the O-star gave me the right pin from sticker. And IM tool did the programming. (O-Star would not).
Old key got accepted and new also went in. And start the car. With both keys.
But KD gave me the wrong remote. So it ended up as a back up key, without remote.

[newone]

But KD gave me the wrong remote. So it ended up as a back up key, without remote.

kd TIIDA 433 28268-9H20A works ok

[lion0304]

This was the original file.


Use your K518, read BCM to get new pin then program. Use good after market or genuine PCF7936

[super jumbe]

all ffff my friend

The reason its showing FFFF is because this car has 12 digit pin code crap cars.

[fred77]

Maybe because copy the chip doesn't looks professional :)


Non-professional only to you - customer can start car!!

jumbie bet he wished did that way now :banghead:

[Manta1600]

Non-professional only to you - customer can start car!!

jumbie bet he wished did that way now :banghead:

This was a joke

You don't have sense of humor