eurovox ex5000pvr dead ?????

[SCOOTA]

re dead ex5000pvr

i too have one of these brought of ebay as spares or repair just has the 2 dots were it would show time i think some-one my of tried to update it i have a buffered jtag i use sb modems so does any one know the pin-outs for the jtag as ive looked at those for starview and eurovox 20 pin but lots of these pins not used

[cutyrca]

i need the flash

hellow i need dxd426re flash

[chic.]

Hi and welcome to dk you will have to leave it 15/20 mins to download

[moinul]

have to post 2 times to get the firmwire

[moinul]

i also bought eurovox 5100 .just waiting for it to be delivered

[chic.]

yes that is the tsop i uploaded from my box its in downloads

[alliv]

EX5000 clone TSOP file tested and working

Box completely dead no lights after updating with Feb UFL no sort, jtagged with jkeys and working again.



(thanks to chic @ wizard)

hi there. have the same prob. will i just flash this on or is it just a tut?

[philup1000]

Is there a tutorial on jtagging a ex5000 ?

thanks

[chic.]

well mavrick2007 first you will need to get a eurovox jtag you can get 1 hear Tailor-Made Circuits then do as the post above but when you connect the 20 pin connector to the box turn it round so that pin 20 goes to pin 1 on the 20 pin header in the box pin 1 on the jtag has the red wire the rest are gray

[Mavrick2007]

EX5000 clone TSOP file tested and working

Box completely dead no lights after updating with Feb UFL no sort, jtagged with jkeys and working again.



(thanks to chic @ wizard)

I'm a complete novice and have the same problem, what do I do first? How do I jtagg? I'm a noivce, sorry to ask.

[jon523115]

Powering the box off after going into Dev panel doesn't sound right, but it seems like your are nearly there.

Does your box have a silver heat sink on the main chip in the middle of the circuit board? (silver heat sink means a clone so I have read)

Anyhow try this:

JTAG tut I used from other forum modified for EX5000, if you get any errors (apart from those mentioned) power box off and start again.


Connect JTAG and Power up EuroVox

Start JKEYS

Click on "Development Panel"
Click OK to ingore the warning.

** SEE BELOW IF YOU GET AN ERROR HERE **

If all goes well you will get into the development panel.

In the user functions box:

Type in the address: 80000000 (eight and seven zeros)
Click on "Load to . . ."

Select the file "unlock_28FxxxC3.bin"

Click "Trigger User"

Close the current window.

Click on "Flash Programming"

Choose the model number as: DXD426RD (1 Chip-GLA)


In the section on the right:

Leave the box above set to "Full"

(Click "Read" and save file if you want to back up existing TSOP)

Click "Erase"

Select YES. This will take a minute to erase.

Click on "Program"

Select YES to "Program at address 0x7FE00000, size 0x200000?"

Choose your TSOP file- DXD426RD(1Chip-GLA) - Flash 1(28F160) - Full.bin
Sit and wait for OK to become active, then click it.

Close JKEYS and power the box down.

Disconnect your JTAG

Power the box on. If all has gone well then it should boot up ready for you to rescan for your channels.




*** If you get an error trying to get into the devleopment windows ****

Power the box down and run SkyMax v2.2
Select 2Mb Adr Flash
Power the box up
Press start.

This seems to reset the box when JKEYS cannot connect (DCU errors).

Close SkyMax and start JKEYS and try again.

[alex123]

everything seems ok other than factory reset before you flash if it was a clone i believe the nov firmware would sort your box after jtag, if you had a clone feb firmware would kill it straight away as soon as you powered box off and on

[iliveinuk]

hi alex, bought from a friend in plymouth who gets about 10 at a time from a family member who lives in liverpool, thats about as far as i know. It just seemed to start playing up a while after loading the DarX firmware, and I have read that would kill a clone, so im guessing mine is.

with jkeys, i ran it, it detected the box, i choose development tools, i then had to power off box, then back on and hit ok on the screen, i then typed in 80000000 and hit load, selected unlock_28FxxxC3, closed that window, hit flash programming, selected the type of chip from pull down menu, then hit erase, it told me to wait while it was erasing, then i hit program and selected the tsop i have got for the ex5000, DXD426RD(1Chip-GLA) - Flash 1(28F160) - Full

It then proceeded to flash.

When its done i power off and back on and thats when i get the red stanby light come on with the four ---- on the display, then they move for a few seconds then it repeats

Am i doing anything wrong with the jkeys????

I used the same tsop as the one a few posts back up on this page

[alex123]

how can you tell if your ex5000 is a clone, had mine since oct last year only flashed it once and its still working fine but if it goes down how can i tell if i need to use clone safe firmware

only differance is the shity printing on the box ,there was not that many clones about in october pm me with site you bought from and will tell you if they sell clones or not
alex

[alex123]

ive not had to jtag a 5000 yet ,which tsop did you use ie was it for a 5000 ?
alex