Hi all i have a digivox silver with the latest software on the box. I get all freeview channels and always got all the locked channels,the problem is it wont update propely now.It says updating data and the percentage goes up but it doesnt work.The problem i have found is as you no there is 2 code lines in nagravision the 00 line and the 01 line.The problem i have is it is stuck on 2 00 lines so cant update.You should beable to imput 01 on one of the 00 lines and ok it to save the line but when i try and go into nagravision it freezes then when the codes come up it looks different and when i press ok after changing one of the 00 lines to a 01 line it freezes completly and the only thing i can do is switch the box off.I have tried downloading the new software again but still the same.Ineed to beable to put a 00 line in can anyone help.Thanks.
-
-
by doing a, set default key, that will clear data to input new data,when changing from 00 -01 use the < or > to change to 01 ,updating firmware would be a better option. -
Lost channels
Hi guy's got a digivox silver but over the last few days iv been losing channels. Done a scan but half the channels have no names ie bbc itv etc. They appear tv1234 tv1723, but its only half the channels any ideas on how to get all the names back.
CheersComment
-
factory reset 0000 to delete,and autoscan again,make sure u are scanning from a direct feed from wall socket ,and emu to on.u should see named channels appear.Comment
-
s**t wish i'd seen that post sooner cactikid might have saved me a bit of work, anyway here's what i did in case it helps anyone else, not saying its the correct way but it worked for me
Ok went into system info pressed 1004, hit "set default key" then turned "Key EMU" to off.
turned the digivox off, turned pc off, connected my null modem to digivox and pc, turned digivox on turned pc on.
opened up downloader 10 and browsed for digivox_z20081222_v4300_api, both of which i dl from site, then hit download
once download had completed turned digivox off turned pc off then disconnected digivox from pc
set digivox up with scart and cable, went straight to system info then nagravision and entered new keys for my area, saved them then went to installation and did automatic scan, once finished went back into system info and turned "key EMU" back on, simples, dont mock this is really good for a newbie who has never flashed a box before, so is that me a mod
Comment
-
s**t wish i'd seen that post sooner cactikid might have saved me a bit of work, anyway here's what i did in case it helps anyone else, not saying its the correct way but it worked for me
Ok went into system info pressed 1004, hit "set default key" then turned "Key EMU" to off.
turned the digivox off, turned pc off, connected my null modem to digivox and pc, turned digivox on turned pc on.
opened up downloader 10 and browsed for digivox_z20081222_v4300_api, both of which i dl from site, then hit download
once download had completed turned digivox off turned pc off then disconnected digivox from pc
set digivox up with scart and cable, went straight to system info then nagravision and entered new keys for my area, saved them then went to installation and did automatic scan, once finished went back into system info and turned "key EMU" back on, simples, dont mock this is really good for a newbie who has never flashed a box before, so is that me a mod
are you in ireland i have downloaded new software to box should i just run a scan now and see or do i have to input codes for ireland trew info and 1004,what are the codes if i do have to do thisComment
-
in irl that box will update but the problem is new encryption which that box cannot do sorry.one point any time u flash a box u need to factory reset first,reflash ,and then a fresh scan and emu on.always read before u post as it is usually posted before.Comment
Comment